Skip to the content
2 layers60 × 60 mmRf lna, the printed circuit board in 3D

915 MHz GaAs MMIC Low Noise Amplifier (LNA) PCB built around the Qorvo SPF5189Z. KiCAD design (DRC clean), LTspice bias and supply-filter simulation, planned ADS S-parameter analysis and VNA validation. v2 migration to SPF5043Z planned.

Size
60 × 60 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
7
Pads
30
Tracks, vias
29, 79
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
29 May 2026
Updated
29 May 2026

Overview

Rf lna is an open-source printed circuit board by Jakcar22, from the Jakcar22/rf-lna repository on GitHub. It is a 2-layer board of 60 × 60 mm with 10 parts on 7 nets, routed with 29 tracks and 79 vias.

Its parts include 4 capacitors, 3 connectors, 2 inductors and 1 IC. It belongs with the radio and wireless and audio and music boards of this library.

README

README.md

915 MHz GaAs MMIC Low Noise Amplifier (LNA) PCB

A 915 MHz low-noise amplifier printed circuit board built around a Qorvo GaAs pHEMT MMIC, designed as part of a self-directed RF hardware project targeting aerospace and defense applications.

Project Summary

This project takes a commercial GaAs MMIC LNA and builds a complete RF front-end PCB around it: bias network, supply filtering, DC blocking, and 50 Ω microstrip routing. The goal is end-to-end ownership of an RF design from datasheet study through KiCAD layout, simulation, fabrication, and VNA validation.

Version 1 (in this repository): Built around the Qorvo SPF5189Z GaAs MMIC LNA. KiCAD layout complete (DRC clean, ERC clean). LTspice bias and supply-filter simulations complete.

Version 2 (planned): Migration to the Qorvo SPF5043Z GaAs MMIC LNA. The SPF5043Z draws 46 mA versus the SPF5189Z's 90 mA, offering better power efficiency at modest cost in gain. Footprint swap (SOT-363 to SOT-343), trace re-route, and bias network re-simulation are planned.

Design Goals

  • Target Frequency: 915 MHz (ISM band)
  • Substrate: FR4 (εr ≈ 4.4), 1.6 mm thickness
  • System Impedance: 50 Ω
  • Target Performance (per SPF5189Z datasheet):
    • Gain (S21): ~19 to 20 dB at 915 MHz
    • Noise Figure: ~0.6 dB
    • Supply: 5 V at ~90 mA
    • Output P1dB: ~22 to 23 dBm

Circuit Architecture

The SPF5189Z has integrated internal impedance matching, so the external circuit is minimal:

text
RF IN --[C2 100 pF block]--[L1 1.5 nH match]-- Pin 1 (RF IN)
                                                  |
                                              SPF5189Z
                                                  |
Pin 3 (RF OUT / DC BIAS) --[C3 100 pF block]-- RF OUT
        |
   [L2 150 nH RF choke]
        |
   [C4 100 pF + C1 100 nF bypass]
        |
      5 V supply

Pin 2, Pin 4 -> GND (with via stitching directly at chip)

Pin 3 dual purpose: Pin 3 is both the RF output AND the DC bias input for VDD. The 150 nH inductor acts as an RF choke (passes DC, blocks 915 MHz). The 100 pF cap on the output passes RF while blocking the supply DC from reaching the load.

Bill of Materials

ReferenceValueFunction
U1SPF5189ZGaAs MMIC LNA
C1100 nF (0.1 µF)VDD bypass (bulk)
C2, C3, C4100 pFDC blocks on RF input, RF output, VDD
L11.5 nHInput matching inductor
L2150 nHVDD RF choke
J1, J2SMA Edge MountRF input/output connectors
J31x2 header5 V power input

Tools Used

  • KiCAD 9.0 — Schematic capture and PCB layout
  • LTspice — DC operating point and AC sweep simulation
  • Keysight ADS — S-parameter and noise-figure simulation (planned, via Purdue ECN)
  • OSHPark — PCB fabrication (planned)
  • VNA — S11 and S21 validation (planned post-fabrication)

Board Specifications

  • Layers: 2-layer FR4
  • Thickness: 1.6 mm
  • Trace Width: 3.0 mm for 50 Ω microstrip on FR4 1.6 mm
  • Layout Rules:
    • RF traces kept short and direct between SMA and chip
    • Ground stitching vias placed around RF traces
    • Power supply traces routed away from RF signal path
    • Via holes placed adjacent to GND pins to minimize inductance
  • DRC: Clean (0 violations, 0 unconnected items)
  • ERC: Clean (0 violations)

Simulation Results

LTspice: Supply-Rail Isolation (AC Sweep)

Verified that the L2 RF choke and C1 bypass capacitor prevent the 915 MHz RF signal from coupling back into the supply line. AC sweep from 1 MHz to 4 GHz, with 1 V AC source representing the worst-case RF leakage into the supply node.

FrequencyAttenuation at VDD Node
50 MHzapproximately -64 dB
915 MHzapproximately -114 dB
4 GHzapproximately -144 dB

Result: The supply filter provides approximately 114 dB of RF isolation at the operating frequency. RF signal cannot meaningfully couple back into the power supply, so the bias circuit is stable.

LTspice: DC Operating Point

Modeled with V1 = 5 V DC, L2 = 150 nH, R1 = 55.6 Ω (SPF5189Z equivalent chip resistance at 90 mA), C1 = 100 nF bypass.

Node / ComponentSimulatedExpectedStatus
V(n001) — VDD node5.000 V5 VPass
V(n002) — after RF choke4.99991 V~5 VPass
I(R1) — chip bias current89.9 mA~90 mAPass
I(L2) — choke current89.9 mA~90 mAPass
I(C1) — bypass cap current~0 A0 A (open at DC)Pass

Result: DC bias network delivers 5 V at 90 mA to the chip as specified in the SPF5189Z datasheet.

Keysight ADS: S-Parameter and Noise-Figure Analysis (Pending)

Planned simulations once the Touchstone (.s2p) model is loaded into ADS via Purdue ECN:

  • S21 (gain) vs frequency, with markers at 915 MHz
  • Noise Figure (NF) and NFmin vs frequency
  • S11, S22 vs frequency (log-magnitude and Smith Chart)
  • P1dB (output 1 dB compression point)
  • Stability factors K and B1 vs frequency

ADS simulation files and output plots are not included in this repository.

Validation Plan (Post-Fabrication)

  1. Visually inspect solder joints under magnification
  2. Measure DC operating point with bench DMM (verify 5 V supply, ~90 mA current for SPF5189Z)
  3. Connect to VNA and measure:
    • S11 (input return loss) — target dip below -10 dB at 915 MHz
    • S21 (gain) — target ~19 to 20 dB at 915 MHz
    • S22 (output return loss) — target below -10 dB
  4. Compare measured S-parameters against simulation results
  5. Document any discrepancies and root-cause them

Project Status

  • Theory reading and reference application circuit studied
  • BOM finalized for SPF5189Z
  • LTspice DC operating point simulation (5 V at 89.9 mA confirmed)
  • LTspice AC sweep supply filter performance (~114 dB isolation at 915 MHz)
  • KiCAD schematic capture (ERC clean)
  • KiCAD PCB layout (DRC clean)
  • Gerber export
  • PCB ordered from OSHPark
  • Keysight ADS S-parameter simulation
  • Board assembled and DC operating point measured
  • VNA measurements (S11, S21, S22) taken
  • Simulation vs measured comparison documented
  • v2 migration to SPF5043Z (footprint swap, re-route, bias re-simulation)

References

License

Hardware design files (schematics, PCB layouts, BOM, Gerbers) are released under the CERN Open Hardware License Version 2 - Permissive (CERN-OHL-P). Software and documentation are released under the MIT License.


Project in active development. Boards not yet fabricated. Measurements not yet taken. README will be updated as milestones complete.

Parts

10
QtyValueFootprintReferences
3100pFCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC2, C3, C4
2Conn_CoaxialConnector_Coaxial:SMA_Samtec_SMA-J-P-H-ST-EM1_EdgeMountJ1, J2
11.5nHInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderL1
1100nfCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC1
1150nHInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderL2
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1SPF5189ZPackage_TO_SOT_SMD:SOT-363_SC-70-6_HandsolderingU1

Similar boards

  • 2 layers57 × 55.2 mmLogicAnalyzer, the printed circuit board in 3D

    LogicAnalyzer

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    10 parts5.1kGPL-3.0
  • 2 layers32.2 × 15.4 mmProtector, the printed circuit board in 3D

    Protector

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    10 parts4.3kMIT
  • 2 layers26 × 18 mmConn, the printed circuit board in 3D

    Conn

    yaqwsx/KiKit

    Automation tools for KiCAD

    10 parts2.1kMIT
  • 2 layers44.3 × 30.5 mmLime2-SATA RevA, the printed circuit board in 3D

    Lime2-SATA RevA

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    10 parts1.5k
  • 2 layers17.8 × 43.2 mmNano Adapter, the printed circuit board in 3D

    Nano Adapter

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    10 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    10 parts1kGPL-3.0

Questions

How big is the Rf lna PCB?

It measures 60 × 60 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rf lna use?

10 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rf lna KiCad files?

From the Jakcar22/rf-lna repository on GitHub, at the commit this page was made from: the board is rf-lna.kicad_pcb and its schematic rf-lna.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rf lna design in my own project?

Its repository states no licence, so its author keeps all rights: ask Jakcar22 before reusing the design.