4 layers36.5 × 46 mm
4 layers29.8 × 34.3 mm
ESP32-C3-Mini
JL0100/My_PCB-Design_Projects- Size
- 29.8 × 34.3 mm
- Copper layers
- 4
- Thickness
- 1 mm
- Parts
- 29
- Nets
- 29
- Pads
- 139
- Tracks, vias
- 211, 52
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 12 Jun 2025
- Updated
- 29 Oct 2026
Overview
ESP32-C3-Mini is an open-source printed circuit board by JL0100, from the JL0100/My_PCB-Design_Projects repository on GitHub, published under the MIT licence. It is a 4-layer board of 29.8 × 34.3 mm with 29 parts on 29 nets, routed with 211 tracks and 52 vias.
It is built around the ESP32-C3-WROOM-02-H4, AP2112K-3.3 and USBLC6-2SC6, with the PESD5V0S1UL among its other parts. Its parts include 10 capacitors, 9 resistors, 3 ICs, 3 connectors and 1 diode. It belongs with the ESP32 and RISC-V boards of this library.
Main components
4
ESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
AP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
PESD5V0S1UL
DFN1006-21 100nA 150W 152pF 15A@8/20us 20V 5V 6.4V ESD IEC 61000-4-2、IEC 61000-4-5 Unidirectional DFN1006-2 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C5 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric | R5, R7, R8, R9 |
| 3 | 100n | Capacitor_SMD:C_0402_1005Metric | C6, C9, C10 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | Conn_01x08_Pin | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2, J3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | BOOT, RST |
| 2 | TBD | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 1 | 0R | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | AP2112K-3.3 | PCM_SparkFun-Semiconductor-Standard:SOT23-5 | U2 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U3 |
| 1 | PESD5V0S1UL | Diode_SMD:D_SOD-882 | D1 |
| 1 | TBD | Resistor_SMD:R_0201_0603Metric | R4 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
Similar boards
- 4 layers90 × 36 mm
A3-before crystal refinement
bdini13/esp32-cc1101-multiband
Work-in-progress ESP32-WROOM-32E + CC1101 multiband PCB: software-selected 315/433/868/915 MHz paths. AI-assisted engineering draft; not manufacturing-ready.
121 parts1 - 6 layers140 × 100 mm
Sbc baseboard
calicopizzadelivery/sbc-development-baseboard
Baseboard for remote management of an attached SBC: K64 MCU as USB HID to the target and Ethernet to the workstation, six switched USB-A ports, isolated SPDT relays, level-shifted console, switched target power
271 partsApache-2.0 - 4 layers61 × 41 mm
- 2 layers41.5 × 59 mm
Mouse
komeed/mouse
Used the PAW3212 Sensor to build a custom mouse pcb and firmware to have a fully operational mouse.
34 parts - 4 layers34.9 × 48.5 mm
- 4 layers54 × 63.4 mm
RaceTracker v3
jonaschramm/race-tracker
Custom PCB data logger for motorcycle racing: GPS position + IMU motion data, logged to a microSD card, with an e-Paper status display. Built around an ESP32-S3 (WiFi/BT built in) so it can also stream/sync over WiFi.
49 parts - 2 layers33.3 × 38 mm
ESP32-C3-WROOM02 dev board
pushtiujeniya/ESP32-C3-WROOM02_dev-board
This project is a custom 2-layer development board designed around the ESP32-C3-WROOM-02 Wi‑Fi + Bluetooth MCU module.
30 parts2
Questions
How big is the ESP32-C3-Mini PCB?
It measures 29.8 × 34.3 mm and has 4 copper layers, 1 mm thick.
What parts does the ESP32-C3-Mini use?
29 parts, built around the ESP32-C3-WROOM-02-H4, AP2112K-3.3, USBLC6-2SC6 and PESD5V0S1UL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32-C3-Mini KiCad files?
From the JL0100/My_PCB-Design_Projects repository on GitHub, at the commit this page was made from: the board is ESP32-C3_Mini_KiCad/ESP32-C3-Mini.kicad_pcb and its schematic ESP32-C3_Mini_KiCad/BlockDiagram.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32-C3-Mini design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).