

Custom ESP32 Development Board PCB designed using KiCad with DHT22 sensor interface, USB connectivity, and 3.3V power regulation.
- Size
- 106.3 × 51.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 68
- Pads
- 163
- Tracks, vias
- 196, 27
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 15 Jul 2026
- Updated
- 16 Jul 2026
Overview
ESP32 DHT is an open-source printed circuit board by Indhiraarunachalam, from the Indhiraarunachalam/ESP32_Development_Board_PCB_Design repository on GitHub, published under the MIT licence. It is a 2-layer board of 106.3 × 51.2 mm with 37 parts on 68 nets, routed with 196 tracks and 27 vias.
It is built around the ESP32-WROOM-32E-H4, CP2102C-A01-GQFN28 and AMS1117-3.3, with the LESD5D5.0CT1G and SS8050-G among its other parts. Its parts include 11 resistors, 9 capacitors, 4 ICs, 4 diodes and 2 transistors. It belongs with the sensors and measurement and interfaces and adapters boards and the ESP32 boards of this library.
Main components
5ESP32-WROOM-32E-H4
SMD,25.5x18mm-40℃~+105℃ -98dBm 112mA 2.4GHz 20dBm 239mA 3V~3.6V Bluetooth4.2 ESP32-DOWD-V3 On-board PCB Antenna UART、SDIO、SPI、I2C、GPIO SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesCP2102C-A01-GQFN28
QFN-28QFN-28 USB Converters ROHSSilicon LabsUSB ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLESD5D5.0CT1G
SOD-523-55℃~+150℃ 100W 12pF 16V 1uA 5V 7A 7V Bidirectional ESD IEC 61000-4-2 SOD-523 ESD and Surge Protection (TVS/ESD) ROHSGOODWORKUncategorisedSS8050-G
SOT-231 NPN 1.5A 100 100MHz 100nA 25V 300mW 400mV 5V NPN SOT-23 Bipolar (BJT) ROHSComchipBipolar (BJT)
README
README.mdESP32 Development Board PCB Design
Overview
This project presents the design of a custom ESP32 Development Board PCB developed using KiCad. The board includes USB connectivity, a regulated 3.3V power supply, reset and boot circuits, and a DHT22 temperature and humidity sensor interface. The design follows the complete PCB development workflow from schematic capture to PCB layout and Gerber generation.
Features
- ESP32 Development Board
- DHT22 Temperature & Humidity Sensor Interface
- USB Power Input
- 3.3V Voltage Regulator
- Reset (EN) Button
- Boot Button
- Status LED
- Two-Layer PCB Design
Software Used
- KiCad
Hardware Components
- ESP32-WROOM Module
- DHT22 Sensor
- USB Connector
- AMS1117-3.3V Voltage Regulator
- Push Buttons
- LEDs
- Resistors
- Capacitors
- Transistor
Design Flow
- Schematic Design
- ERC Verification
- PCB Layout
- Component Placement
- Routing
- DRC Verification
- Gerber Generation
Design Verification
- ERC Passed ✅
- DRC Passed ✅
- Gerber Files Generated Successfully ✅
- Ready for PCB Fabrication ✅
Repository Structure
ESP32-Development-Board-PCB-Design
│
├── ESP32_DHT.kicad_sch
├── ESP32_DHT.kicad_pcb
├── README.md
│
├── Gerber/
│
└── Images/
├── Schematic.png
├── PCB_Toplayer.png
└── PCB_Bottomlayer.pngProject Images
Schematic


PCB Layout - Top Layer

PCB Layout - Bottom Layer

Author
Indhira A
Electronics and Communication Engineering Student
Interested in PCB Design, Embedded Systems and IoT.
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | fab:C_0603 | C2, C3, C7, C8, C9 |
| 5 | 10k | fab:R_0603 | R1, R3, R7, R8, R9 |
| 4 | MountingHole_2.1mm | MountingHole:MountingHole_2.1mm | REF1, REF2, REF3, REF4 |
| 3 | 22uF | fab:C_0603 | C1, C4, C5 |
| 3 | LESD5D5.0CT1G | SamacSys_Footprints:LESD5D50CT1G | D5, D6, D7 |
| 2 | 0R | fab:R_0603 | R10, R11 |
| 2 | SS8050-G | SamacSys_Footprints:SOT95P240X115-3N | Q1, Q2 |
| 2 | Switch_Tactile_ESwitch | fab:Button_ESwitch_TL3315NF100Q_4.5x4.5mm | SW1, SW2 |
| 1 | 10uF | fab:C_0603 | C6 |
| 1 | 1k | fab:R_0603 | R2 |
| 1 | 22.1k | fab:R_0603 | R5 |
| 1 | 2k | fab:R_0603 | R4 |
| 1 | 47.5k | fab:R_0603 | R6 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | CP2102C-A01-GQFN28 | SamacSys_Footprints:QFN50P500X500X80-29N-D | IC1 |
| 1 | DHT22_Temperature_and_humidity_sensor | SamacSys_Footprints:DHT22Temperatureandhumiditysensor | IC2 |
| 1 | ESP32-WROOM-32E-H4 | SamacSys_Footprints:ESP32WROOM32EH4 | IC3 |
| 1 | LED_0603 | fab:LED_0603 | D1 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J1 |
Similar boards
- 4 layers142 × 90 mm

- 4 layers27.5 × 35.8 mm

Robot cortex
Ocanath/robot-coprocessor-pcb
ESP32+STM32 Coprocessor. Standalone, with vendored PCB design out of the old coprocessor repository
91 parts - 2 layers28.5 × 53.6 mm

- 2 layers204.3 × 75.1 mm

PanelizedESP32
valeriyproklov/ESP32-devboard
An ESP32 devboard I designed in KiCad.
491 parts2CERN-OHL-P-2.0 - 2 layers

Amiplantainit
daguilar43/proyectoEmbebidos
Aquí pueden encontrarse todos los archivos del proyecto Amiplanta realizado para la materia Sistemas Embebidos durante el semestre 2022-2 en la Universidad Nacional de Colombia.
50 parts - 4 layers38.8 × 63 mm

TGC Core ULTRA32-v1
ThatGuyCodes605/TGC-Core-ULTRA32-v1
My fastest and best devboard I ever made
32 partsGPL-3.0 - 4 layers155 × 52 mm

Drawer Controller
Robast-GmbH/PCB_Designs
This repository contains all the necessary files and instructions for the PCBs that are designed using KiCad. Here is an overview of the main components: - .github: Contains Github-specific configurations, including…
198 parts1MIT - 4 layers123.3 × 61 mm

Questions
How big is the ESP32 DHT PCB?
It measures 106.3 × 51.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32 DHT use?
37 parts, built around the ESP32-WROOM-32E-H4, CP2102C-A01-GQFN28, AMS1117-3.3 and LESD5D5.0CT1G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32 DHT KiCad files?
From the Indhiraarunachalam/ESP32_Development_Board_PCB_Design repository on GitHub, at the commit this page was made from: the board is ESP32.kicad_pcb/ESP32_DHT.kicad_pcb and its schematic ESP32.kicad_sch/ESP32_DHT.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32 DHT design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).