
Auto dut tester interface board
INTenX/g3-mb-tester-Interface-pcb
Measurement, GPIO, and Communications Interface circuitry between Test Controller and DUT

Measurement, GPIO, and Communications Interface circuitry between Test Controller and DUT
Dut tester interface board is an open-source printed circuit board by INTenX, from the INTenX/g3-mb-tester-Interface-pcb repository on GitHub. It is a 4-layer board of 60.1 × 97 mm with 73 parts on 151 nets, routed with 2,418 tracks and 297 vias.
It is built around the HEF4051BTT, RMCF1206JT22R0 and RMCF0805FT3K48, with the 20021321-00014C4LF among its other parts. Its parts include 44 resistors, 9 connectors, 6 capacitors and 5 ICs. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 37 | 0Ohm | Resistor_SMD:R_0805_2012Metric | R1, R2, R11, R12, R13, R14, R15, R16, R17, R18, R20, R21, R22, R23, R24, R25 +21 |
| 7 | Conn_01x10 | Library:PinSocket_1x10_P2.54mm_Vertical | J1, J2, J3, J4, J5, J6, J7 |
| 6 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C18, C21, C22, C23 |
| 4 | HEF4067BTT | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U1, U3, U11, U12 |
| 4 | MountingHole | MountingHole:MountingHole_3.5mm_Pad | H1, H2, H3, H4 |
| 2 | 22 | Resistor_SMD:R_1206_3216Metric | R30, R31 |
| 2 | MountingHole | MountingHole:MountingHole_3.5mm | H5, H6 |
| 1 | 10 | Resistor_SMD:R_1206_3216Metric | R19 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R32 |
| 1 | 3.48K | Resistor_SMD:R_0805_2012Metric | R36 |
| 1 | 4.53K | Resistor_SMD:R_0805_2012Metric | R37 |
| 1 | 90.9K | Resistor_SMD:R_0805_2012Metric | R38 |
| 1 | Conn_01x20 | Library:PinHeader_1x14_P2.54mm_Vertical_Oval_Pads | J15 |
| 1 | Conn_ST_STDC14 | Connector_PinHeader_1.27mm:PinHeader_2x07_P1.27mm_Vertical_SMD | J9 |
| 1 | ESP32-S3-DevKitC_1-22 | Library:ESP32-S3-DevKitC_1-22 | ESP-1 |
| 1 | ESP32-S3-DevKitC_23-44 | Library:ESP32-S3-DevKitC_23-44 | ESP-2 |
| 1 | HEF4051BTT | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U8 |
| 1 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1 |

INTenX/g3-mb-tester-Interface-pcb
Measurement, GPIO, and Communications Interface circuitry between Test Controller and DUT



benanderman/spork-8
An 8-bit CPU, made with TTL chips on custom, modular PCBs. Includes board designs, and Arduino code to program its instruction set and programs.

FPV-Drone-STM32F411/DroneController
All-in-one FPV drone PCB with integrated flight controller, PDB, and ESCs built around STM32F411.



Misaka0x2730/MioLink
ARM JTAG/SWD debugger (BlackMagic port) based on RP2040.

chipsalliance/rocket-pcb
PCB libraries and templates for rocket-chip based FPGA/ASIC designs
It measures 60.1 × 97 mm and has 4 copper layers, 1.6 mm thick.
73 parts, built around the HEF4051BTT, RMCF1206JT22R0, RMCF0805FT3K48 and 20021321-00014C4LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the INTenX/g3-mb-tester-Interface-pcb repository on GitHub, at the commit this page was made from: the board is dut-tester-interface-board.kicad_pcb and its schematic dut-tester-interface-board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask INTenX before reusing the design.