
Carte puissance
INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup
Encodeurs DFRobotics is an open-source printed circuit board by INSA-GEI, from the INSA-GEI/insa-nxpcup repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 47 × 20 mm with 12 parts on 8 nets, routed with 133 tracks and 12 vias.
It is built around the 74LVC2G34GW, SFH 9206 and DF3A-5P-2DSA. Its parts include 4 resistors, 4 ICs, 2 capacitors and 2 connectors.
Repository for INSA NXP cup
Every folder titled source_[...] is a version of the code. One should only put the *.c and the *.h of the project, not the entire folder !
[...] Is a keyword or a_small_sentence describing this version in particular (e.g. "source_dangerously_fast" or "source_safest").
Small survival kit for everyone :
Get here and follow the installer's instructions. One should avoid using github desktop client ;)
git clone https://github.com/INSA-GEI/insa-nxpcup-1.git
cd insa-nxpcup-1git pull If it doesn't work, save your changes elsewhere, and retry with
git stash #Cancels all your changes in the repo
git pull #Try pulling againUpload as often as possible. Most errors here appear when working un un-updated code.
git commit -a #Prepare a commit with all updated files, ignoring new files.
git push #Sends the previous commit on this repoNB : While commiting, use Esc :wq Enter. A good commit message is brief, and completes the following statement : This commit will ....
Do not use branches yet ! Your are in branch master, nothing should be done here Select a valid branch:
git checkout int_team_1: Integration branch for team 1
git checkout int_team_2: Integration branch for team 2team work should use int_team_x branch as their main branch and integrate inside every stable work. Use development branch for your work in progress.
Old branchs: git checkout stable : stable branch (Obsolete) git checkout dev : work in progress (Obsolete)
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 200 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R3, R4 |
| 2 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C4 |
| 2 | 74LVC2G34 | Package_TO_SOT_SMD:SOT-363_SC-70-6_Handsoldering | U3, U4 |
| 2 | DF3A-5P-2DS | Insa:DF3A-5P-2DS | J1, J2 |
| 2 | SFH9206 | OptoDevice:Osram_SFH9x0x | U1, U2 |

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

INSA-GEI/insa-nxpcup
Dépôt du département GEI de l'INSA Toulouse pour la compétition NXPCup

crisbour/filterox
Filter Wheel Oxidised (Rust) - Control N slots filter wheel remotely

INSA-GEI/gei-nxpcup-4w-pwr
Power part for 4 wheels model car used in NXPCUP contest at INSA-GEI

efabless/foss-asic-tools
FOSS-ASIC-TOOLS is all in one container for SKY130 based design both Analog and Digital. Below is a list of the current tools already installed and ready to use.

introlab/t-top
T-Top is a tabletop robot designed with advanced audio and vision sensors, deep learning perceptual processing and telecommunication capabilities to provide richer interaction modalities and develop higher cognitive…

damienmaguire/MG-EV-Inverter
Reverse engineering of the drive motor and inverter used in MG Electric Vehicles

Duet3D/Duet3-Mini5plus
This repository also contains information in the Mini 2+ : a two driver expansion board for the Duet 3 mini 5+


It measures 47 × 20 mm and has 2 copper layers, 1.6 mm thick.
12 parts, built around the 74LVC2G34GW, SFH 9206 and DF3A-5P-2DSA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the INSA-GEI/insa-nxpcup repository on GitHub, at the commit this page was made from: the board is pcb/DFRobotic/Encodeurs-DFRobotics/Encodeurs-DFRobotics.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).