Skip to the content
2 layers312.8 × 87.6 mmKibod-01, the printed circuit board in 3D

First Split Keyboard PCB design

Size
312.8 × 87.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
87
Nets
65
Pads
338
Tracks, vias
442, 0
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
5 Jan 2022
Updated
25 Oct 2026

Overview

Kibod-01 is an open-source printed circuit board by GreenMashedPotato, from the GreenMashedPotato/Shrimp42 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 312.8 × 87.6 mm with 87 parts on 65 nets, routed with 442 tracks and 0 vias.

Its parts include 2 connectors and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

Shrimp42(previously Kibod-01) Work In Progress

it's a keyboard inspired by Slepet that has more stagger in some columns and only 3 thumb cluster keys instead of 5.

Rev 1 (initial prototype)

Non Mirrored Keyboard uses 1 pro micro with 2x5 10pin IDC Connector: kibod

Mirrored Keyboard, supports using 2 pro micros with trrs, or 1 pro micro with 2x5 10pin IDC Connector: mirror mirror

Rev 2

Mirrored Keyboard Rev2(renamed to Shrimp42): mirror mirror case

improvements from rev1:

  • adds support for hotswap sockets
  • adds support for smd diodes
  • changed angles from 2 to 3 degrees while reducing distance between columns.
  • add board name: Shrimp 42
  • add Stacked Acrylic Case

V1 vs V2 mirror

Materials

QntyRefValueDescription
1 (2 if using trrs)U1Arduino Pro-Micro ATmega32U4
42D-0-0 - D-3-51N4148Diode: 1N4148 (SOD 123 or THT)
42K-0-0 - K-3-5MX or ALPS Switches1U
42 (optional)K-0-0 - K-3-5MX or ALPS Hotswap Socketsthis board supports the use of hotswap sockets and soldered connections
2U2TRRS connectors OR 2x5 10pin IDC Connector
1TRRS Cable OR 2x5 10pin IDC Cableused to connect both halves
2Shrimp42 pcb

Firmware

QMK and VIAL (provided via firmware but will need to sideload json and is untested) firmware for using the keyboard like in my setup above (using the extended GPIO pin to connect both halves and only 1 pro micro). here.

QMK and VIAL for trrs connection (using 2 pro micros, slave board flipped, trrs connecting both sides) here

Library Used

Keebio's footprints Ibnuda's footprints

Contact me:

Reddit u/greenmashedpotato

Disclaimer

I don't reccomend trying rev1 since the innermost and outermost column may be too far for some hands and can be tiring to use for long durations.

I haven't printed some of it. No guarantees that they work.

If things go wrong, I won't take any responisibilities, Try at your own risk.

Additional Notes

After using the 2 in 1 diodes footprint, it may be too hard to know the orientation. make sure the line on the diode is facing the square hole: diode diode

When using the Extended gpio pins to connect both halves, I have only tested using the pro micro on the left.

When using TRRS, dont forget to flip the right pro micro, I have only tested using the left pro micro as Master.

License

GPL-3.0 License

Parts

87
QtyValueFootprintReferences
42Dfootprints:diode-verticalD-0-0, D-0-0-B1, D-0-1, D-0-1-B1, D-0-2, D-0-2-B1, D-0-3, D-0-3-B1, D-0-4, D-0-4-B1, D-0-5, D-0-5-B1, D-1-0, D-1-0-B1, D-1-1, D-1-1-B1 +26
42KEYSWfootprints:100-minimal-no-3dK-0-0, K-0-0-B1, K-0-1, K-0-1-B1, K-0-2, K-0-2-B1, K-0-3, K-0-3-B1, K-0-4, K-0-4-B1, K-0-5, K-0-5-B1, K-1-0, K-1-0-B1, K-1-1, K-1-1-B1 +26
202x05footprints:connector-shroudedJ1, J2
1ProMicrofootprints:promicroU1

More from GreenMashedPotato/Shrimp42

2
  • 2 layers147.3 × 89 mmShrimp42-mirrored rev2, the printed circuit board in 3D

    Shrimp42-mirrored rev2

    GreenMashedPotato/Shrimp42

    First Split Keyboard PCB design

    52 parts8GPL-3.0
  • 2 layers155.2 × 87.6 mmKibod-01-mirrored, the printed circuit board in 3D

    Kibod-01-mirrored

    GreenMashedPotato/Shrimp42

    First Split Keyboard PCB design

    46 parts8GPL-3.0

Similar boards

  • 2 layers175.8 × 184.8 mmSofleKeyboard, the printed circuit board in 3D

    SofleKeyboard

    josefadamcik/SofleKeyboard

    A split keyboard based on Lily58, Crkbd and Helix keyboards

    87 parts2.6k
  • 2 layers58.2 × 38.1 mmUsb sniffer, the printed circuit board in 3D

    Usb sniffer

    ataradov/usb-sniffer

    Low-cost LS/FS/HS USB sniffer with Wireshark interface

    87 parts1.3kBSD-3-Clause
  • 2 layers65 × 56 mmHat, the printed circuit board in 3D

    Hat

    pa3gsb/Radioberry-2.x

    Ham Radio hat for Raspberry PI

    87 parts678
  • 2 layers57 × 111 mmSIM POWER PANEL, the printed circuit board in 3D

    SIM POWER PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    87 parts431
  • 2 layers128.2 × 150.3 mmSplit 3x, the printed circuit board in 3D

    Split 3x

    MangoIV/dracuLad

    QMK-powered 34-36 key split keyboard

    87 parts230
  • 2 layers88.9 × 80 mmEdk, the printed circuit board in 3D

    Edk

    ciaa/Hardware

    Hardware de la CIAA

    87 parts216
  • 2 layers68.6 × 53.3 mmArduino UNO R4 Minima, the printed circuit board in 3D

    Arduino UNO R4 Minima

    sabogalc/KiCad-Arduino-Boards

    A collection of Arduino boards recreated from scratch in KiCad. Legacy USB connectors have been replaced with USB-C where applicable.

    87 parts95WTFPL

Questions

How big is the Kibod-01 PCB?

It measures 312.8 × 87.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Kibod-01 use?

87 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Kibod-01 KiCad files?

From the GreenMashedPotato/Shrimp42 repository on GitHub, at the commit this page was made from: the board is Rev1/non-mirrored Rev1/kibod-01.kicad_pcb and its schematic Case/Rev2/PCB Bottom/PCB Bottom.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Kibod-01 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).