Skip to the content
2 layers68 × 110 mmIndoorNode, the printed circuit board in 3D

Development of a Remote Communications Infrastructure for an Off-Grid Energy System: Hardware, Software, and Data

Size
68 × 110 mm
Copper layers
2
Thickness
1.6 mm
Parts
26
Nets
36
Pads
78
Tracks, vias
65, 0
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
9 Sep 2025
Updated
6 Oct 2025

Overview

IndoorNode is an open-source printed circuit board by Global-Health-Engineering, from the Global-Health-Engineering/remote-comm-solar repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 68 × 110 mm with 26 parts on 36 nets, routed with 65 tracks and 0 vias.

It is built around the DHT22. Its parts include 14 resistors, 5 connectors and 1 IC.

Main components

1

README

README.md

DOI

Development of a Remote Communications Infrastructure for an Off-Grid Energy System: Hardware, Software, and Data

Contributors




It complements the openly-accessible master’s thesis, available on the
ETH Research Collection [blocked].

Overview

Monitoring off-grid energy systems in remote locations with unreliable communications is challenging, yet it is essential in health facilities where continuous power supports patient care. Currently, there is no simple end-to-end solution that reliably captures all relevant variables and forwards them autonomously to a site with internet access for analysis and response.

This thesis develops such a system for an off-grid health clinic in Tezhumke, northern Colombia. The design combines existing low-power sensing and long-range radio techniques with practical extensions for constrained clinical sites. In particular, robustness measures and encoding optimizations were added to improve packet delivery over Long Range (LoRa) links, and the overall architecture was engineered to run autonomously from small photovoltaic panels and local power bank storage.

Custom sensor nodes record key measurements: medical refrigerator temperature and humidity, electrical parameters of the off-grid power system, and environmental data. Measurements are transmitted over LoRa and Long Range Wide-Area Network (LoRaWAN) to a gateway, visualized on an Internet of Things (IoT) platform (ThingsBoard), and automatically archived. Alarm rules notify remote researchers and on-site staff via platform alerts, email, SMS, and visual signals when thresholds are exceeded.

In a 7-day field trial, the system achieved a packet reception rate of 97.64% over a distance of 8.5km and demonstrated stable autonomous operation. These results confirm that the system is a mature prototype ready for extended field trials and potential deployment in real-world conditions. Future work should include extended seasonal testing, long-term studies of battery aging, and improvements to the weatherproofing of individual components.

Beyond the immediate use case in Tezhumke, the system may also be applicable to other similarly affected clinics or remote sites. With further refinement, it could support predictive maintenance strategies and contribute to improved reliability of off-grid power supplies, thereby strengthening healthcare delivery in underserved regions.

Repository

As part of this Master thesis, all developed resources have been collected and systematically documented in this public GitHub repository. The repository serves as a comprehensive reference point for future research and practical applications. It includes:

  • Source code for LoRa / LoRaWAN communication,
  • ThingsBoard dashboard configuration and the main payload decryption script,
  • Dedicated scripts for automated data export,
  • PCB layouts and electronic circuit schematics,
  • All custom-designed 3D models provided in STL format,
  • A complete bill of materials for all hardware components.

Parts

26
QtyValueFootprintReferences
610kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R6, R7, R9, R11, R13
518kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5, R8, R10, R12, R14
4MountingHoleMountingHole:MountingHole_4.3mm_M4H1, H2, H3, H4
2100Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R4
122kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1Battery +/-Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ3
1DHT22TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mmJ6
1Feather 32u4 LoRa SMTModule:mod2_Adafruit_Feather_32u4_RFM_WithMountingHoles_1U1
1LEDTerminalBlock:TerminalBlock_MaiXu_MX126-5.0-03P_1x03_P5.00mmJ1
1LOGOSilkscreenLogo:gheG***
1LOGOSilkscreenLogo:ethG***
1SmartShuntTerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mmJ2
1ebikesTerminalBlock:TerminalBlock_MaiXu_MX126-5.0-08P_1x08_P5.00mmJ5

More from Global-Health-Engineering/remote-comm-solar

1
  • 2 layers68 × 110 mmOutdoorNode, the printed circuit board in 3D

    OutdoorNode

    Global-Health-Engineering/remote-comm-solar

    Development of a Remote Communications Infrastructure for an Off-Grid Energy System: Hardware, Software, and Data

    17 partsApache-2.0

Similar boards

  • 2 layers271.8 × 114.3 mmArdumower mega shield svn, the printed circuit board in 3D

    Ardumower mega shield svn

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    426 parts282
  • 2 layers104.8 × 72.1 mmSST V2 4, the printed circuit board in 3D

    SST V2 4

    mcbittech/souliss-smart-thermostat-WiFi

    ESP8266 WiFi Smart Thermostat based on Souliss IoT Framework

    53 parts110GPL-2.0
  • 2 layers40.6 × 50.8 mmIot sourdough starter monitor, the printed circuit board in 3D

    Iot sourdough starter monitor

    justinmklam/iot-sourdough-starter-monitor

    Tracking the fermentation of sourdough starter over the cloud.

    7 parts93GPL-3.0
  • 2 layers28 × 13 mmDHT22 pcb, the printed circuit board in 3D

    DHT22 pcb

    MakersAsylumIndia/M19O2

    M19O2 open source hardware Oxygen Concentrator based on the Pressure Swing Adsorption cycle aka Skarstorm cycle

    5 parts68MIT
  • 2 layers136 × 100 mmClimateSprinklerController, the printed circuit board in 3D

    ClimateSprinklerController

    kbx81/ClimateSprinklerController

    ESP32-based climate and sprinkler controller for use with ESPHome

    194 parts56
  • 2 layers162 × 60 mmEsp shield, the printed circuit board in 3D

    Esp shield

    felixwittwer/homeassistant_automaic_greenhouse

    A cool Project to make your greenhouse smart. What about automaic irrigation and collecting enviromental data right from your garden.

    20 parts27
  • 2 layers74.9 × 40.6 mmAnavi thermometer, the printed circuit board in 3D

    Anavi thermometer

    AnaviTechnology/anavi-thermometer

    WiFi Smart Thermometer with ESP8266, DHT22, DS18B20, OLED display and slots for up to 3 I2C sensor modules

    25 parts17
  • 2 layers81.3 × 36.8 mmAirQualitySensor, the printed circuit board in 3D

    AirQualitySensor

    Finomnis/AirQualitySensor

    Simple Air Quality sensor based on nRF52840, Zigbee, AM2302/DHT22 and Senseair S8

    44 parts16Apache-2.0

Questions

How big is the IndoorNode PCB?

It measures 68 × 110 mm and has 2 copper layers, 1.6 mm thick.

What parts does the IndoorNode use?

26 parts, built around the DHT22. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the IndoorNode KiCad files?

From the Global-Health-Engineering/remote-comm-solar repository on GitHub, at the commit this page was made from: the board is hardware/PCB/indoorNode/indoorNode.kicad_pcb and its schematic hardware/PCB/RepeaterNode/RepeaterNode.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the IndoorNode design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).