
Panel daisy
ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

The TDS-2 is a simple yet effective distortion pedal based on the TL072 operational amplifier and the Hammond 1590B enclosure.
TDS-2 is an open-source printed circuit board by Flacarica, from the Flacarica/TDS-2 repository on GitHub. It is a 2-layer board of 52 × 100 mm with 27 parts on 19 nets, routed with 146 tracks and 0 vias.
It is built around the TL072. Its parts include 8 resistors, 5 capacitors, 3 diodes, 3 connectors and 1 IC. It belongs with the audio and music boards of this library.
The TDS-2 is the next guitar pedal in the TDS series, with an improved design and use of a standard enclosure.
The main features of the TDS-2 are the use of clipping diodes and a buffering stage, before the op-amp that amplifies the base signal. I've also used a 3PDT footswitch and some audio jacks that hold the line low when no jack is inserted, just to make sure i don't get any unecessary noise.
The main features of the circuit are:

The principle behind the TDS-2 distortion pedal is a high amplification factor. The TL072 IC has two op-amps. The first one is used as a buffer so that the imput signal is high enough. The second op-amp actually amplifies the signal, since it's in a inverting configuration to counter the phase shift of the buffer stage. The amplification factor is given by the potentiometer that connects the oputput back to the inverting input. The capacitors are used to decouple and "delete" any DC voltage that might be present. I used two fast switching diodes to make a clipping stage, to ensure that the signal never goes above and below the +4,5v and -4,5v headroom.

The PCB also has four M3 mounting holes that are connected directly to 0v, so that when I mount it in the enclosure, the aluminium enclosure gets grounded and acts like an EMF shield. One thing I'd improve upon are the traces since they're quite narrow and may be prone to high levels of noise.
The enclosure I picked for this pedal and subsequent versions of it is the Hammond 1590B, since it's made out of aluminium it's relatively cheap and effective. The enclosure offers more of a professional look to the pedal whilst also doubling as protection against EMF and other elements.
I used this datasheet to get the dimensions needed for the PCB, and i found that 10cm x 5cm is more than enough.
This project is not intended for beginners, but with a little guidance it can be a successful starting project.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | , , , | ||
| 4 | 10µF | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C2, C3, C4, C5 |
| 3 | 10kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R7 |
| 2 | 100kΩ | Potentiometer_THT:Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | RV1, RV2 |
| 2 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D2, D3 |
| 2 | 1kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R8 |
| 2 | SN49B14B | footprints:PJ-644C | J5, J6 |
| 1 | 100kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
| 1 | 10µF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1 |
| 1 | 220Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 3.8kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6 |
| 1 | Barrel_Jack_MountingPin | Connector_BarrelJack:BarrelJack_Kycon_KLDX-0202-xC_Horizontal | J1 |
| 1 | POW_LED | LED_THT:LED_D5.0mm | D1 |
| 1 | TL072 | Package_DIP:DIP-8_W7.62mm | U1 |
| 1 | ~ | Library:3PDT Footswitch | FTSW1 |

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ctag-fh-kiel/ctag-tbd
CTAG TBD >>to be determined<< an extendible open source Eurorack sound module

plinkysynth/plinky_public
a public release of the plinky sw and hw



matthewcieplak/super-sixteen
Code and schematics for the Super Sixteen Eurorack sequencer

mzuelch/CATs-Eurosynth
Analog Synth Eurorack Modules

StoneRose35/cortexguitarfx
guitar effects processor implemented on various arm cortex platforms
It measures 52 × 100 mm and has 2 copper layers, 1.6 mm thick.
27 parts, built around the TL072. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Flacarica/TDS-2 repository on GitHub, at the commit this page was made from: the board is KiCAD project files/TDS-2.kicad_pcb and its schematic KiCAD project files/TDS-2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Flacarica before reusing the design.