2 layers
Main automatic manifold
Febriyandi12/Desain_PCB
Kolaborasi untuk update desain pcb yang telah di research
59 parts1
2 layers
Skematik Main Compressor V1
Febriyandi12/Desain_PCB1Kolaborasi untuk update desain pcb yang telah di research
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 92
- Nets
- 105
- Pads
- 366
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 24 Jul 2024
- Updated
- 7 Aug 2024
Overview
Skematik Main Compressor V1 is an open-source printed circuit board by Febriyandi12, from the Febriyandi12/Desain_PCB repository on GitHub. It is a 2-layer board with 92 parts on 105 nets.
It is built around the ESP32-WROOM-32UE-N4, LM2576S-5.0 and MSD-4-A, with the DS3231MZ+, FM24C64B-G and LM1117DT-3.3 among its other parts. Its parts include 29 resistors, 15 connectors, 13 diodes, 12 ICs and 11 capacitors. It belongs with the ESP32 boards of this library.
Main components
8
ESP32-WROOM-32UE-N4
SMD,19.2x18mm-40℃~+85℃ -88dBm 112mA 19.5dBm 2.4GHz 239mA 3V~3.6V Bluetooth4.2 ESP32-D0WD-V3、ESP32-D0WDR2-V3 UART、SDIO、SPI、I2C、GPIO、ADC、I2S、DAC、Ethernet、TWAI SMD,19.2x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
LM2576S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 3A 4V~40V 52kHz 5V 5mA Buck Built-in Fixed No Step-down type TO-263-5 DC-DC Converters ROHSSlkorDC-DC Converters
MSD-4-A
SMDSMD SD Card / Memory Card Connector ROHSCUISD Card / Memory Card Connector
DS3231MZ+
SOIC-8-40℃~+85℃ 2.3V~5.5V I2C Temperature compensation、Backup power management and battery charging、Alarm function、Periodic interrupt output SOIC-8 Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time ClocksFM24C64B-G
-SOIC-8 FRAM ROHSInfineon TechnologiesFRAM
LM1117DT-3.3
TO-2520℃~+125℃@(Tj) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MB6S
MBS-55℃~+150℃ 1.1V@400mA 1A 35A 5uA@600V 600V Single-Phase Rectifier MBS Bridge Rectifiers ROHSMDDBridge Rectifiers
BC547
TO-92Bipolar (BJT)Jiangsu Changjing Electronics Technology (CJ)
Parts
92| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 10K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3, R4, R5, R6, R13, R14, R26, R27 |
| 6 | 1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R2, R11, R17, R18, R28 |
| 6 | PC817 | Package_DIP:DIP-4_W7.62mm | U2, U4, U10, U11, U12, U13 |
| 4 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R22, R23, R24, R25 |
| 4 | 2N5551-TA | Package_TO_SOT_THT:TO-92_Inline_Wide | Q1, Q2, Q3, Q4 |
| 4 | 510 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R12, R15, R16, R29 |
| 4 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2, D4, D5 |
| 4 | SANYOU_SRD_Form_C | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | K1, K2, K3, K4 |
| 2 | 10uF | Capacitor_SMD:CP_Elec_3x5.3 | C5, C6 |
| 2 | 150K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R20, R21 |
| 2 | 4K7 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R8 |
| 2 | C_Polarized_US | Capacitor_SMD:CP_Elec_3x5.3 | C9, C10 |
| 2 | D_Schottky_Small_Filled | Diode_SMD:D_0201_0603Metric_Pad0.64x0.40mm_HandSolder | D8, D9 |
| 2 | MB6S | Package_TO_SOT_SMD:TO-269AA | D6, D7 |
| 1 | 0.1uF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C2 |
| 1 | 1000uF | Capacitor_SMD:CP_Elec_3x5.3 | C8 |
| 1 | 100nF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C3 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C12 |
| 1 | 100uF | Capacitor_SMD:C_Elec_3x5.4 | C7 |
| 1 | 100uh | Inductor_SMD:L_6.3x6.3_H3 | L1 |
| 1 | 10uF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C4 |
| 1 | 1N5822 | Diode_SMD:D_0201_0603Metric | D3 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R19 |
| 1 | 1k8 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R10 |
| 1 | 1k8 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9 |
| 1 | 22uF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C1 |
| 1 | ADS1015 | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J7 |
| 1 | AUTO DRAIN | Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J17 |
| 1 | BC547 | Package_TO_SOT_THT:TO-92_Inline_Wide | Q5 |
| 1 | BIRU | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D13 |
| 1 | Boot | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J12 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Buzzer AC | Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J18 |
| 1 | CO SENSOR | Connector_JST:JST_XA_B03B-XASK-1_1x03_P2.50mm_Vertical | J9 |
| 1 | CR1220MFR_FH | CR1220:CR1220-SMD | BT1 |
| 1 | Conn_01x04_Pin | Connector_JST:JST_EH_B4B-EH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | DS3231M | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U7 |
| 1 | ESP32-WROOM-32UE | RF_Module:ESP32-WROOM-32UE | U1 |
| 1 | FM24C64B | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U9 |
| 1 | IN 12V | Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J13 |
| 1 | JUMPER | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J19 |
| 1 | LM1117DT-3.3 | Package_TO_SOT_SMD:TO-252-2 | U5 |
| 1 | LM2576S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U6 |
| 1 | MERAH | LED_SMD:LED_0402_1005Metric_Pad0.77x0.64mm_HandSolder | D12 |
| 1 | MOTOR IN | Connector_Molex:Molex_KK-396_A-41791-0003_1x03_P3.96mm_Vertical | J2 |
| 1 | MOTOR1 | Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J15 |
| 1 | MOTOR2 | Connector_Molex:Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J16 |
| 1 | MSD-4-A | MSD-4-A:CUI_MSD-4-A | J3 |
| 1 | PREASURE SENSOR | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J8 |
| 1 | RA-02_LORA | RF_Module:Ai-Thinker-Ra-01-LoRa | U3 |
| 1 | SHT31 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6 |
| 1 | TRIP 1 | LED_SMD:LED_0201_0603Metric_Pad0.64x0.40mm_HandSolder | D10 |
| 1 | TRIP 2 | LED_SMD:LED_0201_0603Metric_Pad0.64x0.40mm_HandSolder | D11 |
| 1 | UART | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J1 |
More from Febriyandi12/Desain_PCB
3
Similar boards
- 2 layers55 × 55 mm
ControlBoard
Deni90/singleDigitNixieClock
A small project that combines ESP32 with a vintage Soviet Nixie tube from the 70’ to create an artistic clock. Originally developed on ESP8266/Arduino, now evolved to ESP32 with ESP-IDF for greater performance and…
39 parts5MIT - 2 layers66.2 × 80 mm
SOLDERING IRON CONTROLLER
MAATHES-THILAK-K/Solder-Master-PRO
Professional-grade soldering temperature control on a DIY budget
34 partsApache-2.0 - 6 layers51 × 53.5 mm
Custom fc rat
Ekta-Gupta27/custom-flight-controller-pcb
Custom flight controller PCB designed in KiCad with STM32F7, multiple sensors, CAN, USB, telemetry, PWM and IO interfaces.
122 parts - 2 layers83.7 × 90.3 mm
Incubator Quetta Client
manhoosbilli1/Incubator_basic_esp32_modular_1_sided
This contains an incubator pcb i've made for a client. his needs were specific so only added what he needed. a complete and complex version can be found in capibator organization.
43 parts - 4 layers174 × 104 mm
- 6 layers148.4 × 99.8 mm
- 2 layers100 × 74 mm
Qym solder
basson/qym-solder
QymSolder - Soldering station three in one - hakko t12, hot air gun, d909/898D or analog.
135 parts4GPL-3.0 - 2 layers52.9 × 30.6 mm
Power meter v3 1
KrystianD/avr-power-meter
AVR-based, galvanically isolated, bidirectional DC energy meter with Modbus RTU interface.
50 parts4MIT
Questions
What parts does the Skematik Main Compressor V1 use?
92 parts, built around the ESP32-WROOM-32UE-N4, LM2576S-5.0, MSD-4-A and DS3231MZ+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Skematik Main Compressor V1 KiCad files?
From the Febriyandi12/Desain_PCB repository on GitHub, at the commit this page was made from: the board is Skematik Main Compressor V1/Skematik Main Compressor V1/Skematik Main Compressor V1.kicad_pcb and its schematic Automatic Manifod/Pressure/Pressure.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Skematik Main Compressor V1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Febriyandi12 before reusing the design.