

Battery tester
- Size
- 130 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 132
- Nets
- 113
- Pads
- 462
- Tracks, vias
- 860, 147
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 6 Oct 2023
- Updated
- 26 Aug 2024
Overview
Battery tester is an open-source printed circuit board by Fabien-B, from the Fabien-B/battery_tester repository on GitHub. It is a 2-layer board of 130 × 100 mm with 132 parts on 113 nets, routed with 860 tracks and 147 vias.
It is built around the TMP101NA, BTS7004-1EPP and LM3940IMP-3.3, with the KP-1608SURC among its other parts. Its parts include 39 resistors, 14 capacitors, 11 connectors, 7 ICs and 7 diodes. It belongs with the power boards and the STM32 boards of this library.
Main components
4TMP101NA
SOT23-6-55°C to +125°C, ±3.0°C Accuracy, Digital Temperature Sensor with I2C InterfaceTexas InstrumentsUncategorisedBTS7004-1EPP
TSDSO-14-40℃~+150℃ 1 15A 3.1V~28V 4.4mΩ Active High High Side Switch Over Voltage Protection、Undervoltage Protection(UVP)、Overcurrent Protection(OCP) TSDSO-14 Power Distribution Switches ROHSInfineon TechnologiesPower Distribution SwitchesLM3940IMP-3.3
SOT-223-40℃~+125℃@(Tj) 1 10mA 1A 250uVrms 3.3V 5.5V 500mV@(1A) Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsKP-1608SURC
0603-40℃~+85℃ 120° 2.5V 20mA 250mcd 630nm 645nm 75mW Discrete Diode Red Water Clear 0603 LED Indication - Discrete ROHSKingbrightLED Indication - Discrete
Parts
132| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0603_1608Metric | C_{BYP}1, C_{VS}1, C_{VS}2, C1, C19, C20, C21, C26, C27, C28, C29 |
| 8 | 270Ω | _Resistors_GRZ:R_0603 | R19, R20, R21, R22, R23, R24, R25, R26 |
| 8 | 4.7k | Resistor_SMD:R_0603_1608Metric | R_{ADC}1, R_{ADC}2, R_{DEN}1, R_{DEN}2, R_{IN}1, R_{IN}2, R1, R2 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R10, R11, R12, R13, R15, R16, R17 |
| 7 | 40k | Resistor_SMD:R_0603_1608Metric | R27, R36, R37, R38, R39, R40, R51 |
| 6 | KSC3J | _Switches_GRZ:KSC3J | PB1, PB2, PB3, PB4, PB6, PB7 |
| 5 | KP-1608SURC | _Opto_GRZ:KP-1608SURC | LED1, LED2, LED3, LED4, LED5 |
| 4 | MountingHole | _MountingHole_GRZ:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP6, TP7, TP8, TP9 |
| 3 | 10nF | Capacitor_SMD:C_0603_1608Metric | C_{OUT}1, C_{OUT}2, C23 |
| 3 | 10uF | _Capacitors_GRZ:C_0603 | C8, C10, C11 |
| 3 | 10µF | _Capacitors_GRZ:C_0603 | C2, C4, C6 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP10, TP11, TP12 |
| 2 | 1.2k | Resistor_SMD:R_0603_1608Metric | R_{SENSE}1, R_{SENSE}2 |
| 2 | 100nF | _Capacitors_GRZ:C_0603 | C3, C5 |
| 2 | 18k | Resistor_SMD:R_0603_1608Metric | R8, R18 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C24, C25 |
| 2 | 220p | Capacitor_SMD:C_0603_1608Metric | C_{SENSE}1, C_{SENSE}2 |
| 2 | 390 | Resistor_SMD:R_0603_1608Metric | R3, R14 |
| 2 | 47 | Resistor_SMD:R_0603_1608Metric | R_{GND}1, R_{GND}2 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R41, R42 |
| 2 | BTS7004-1EPP | Package_SO:Infineon_PG-TSDSO-14-22 | U3, U4 |
| 2 | CON05 | _Connectors_GRZ:PicoBlade_53398-0571 | J6, J7 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J9, J10 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D2 |
| 2 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J3, J4 |
| 1 | 0Ω | _Resistors_GRZ:R_0603 | R34 |
| 1 | 100µF | _Capacitors_GRZ:EIA_6032-28 | C9 |
| 1 | 10kΩ | _Resistors_GRZ:R_0603 | R30 |
| 1 | 10mΩ | _Resistors_GRZ:R_0603 | R29 |
| 1 | 15kΩ | _Resistors_GRZ:R_0603 | R32 |
| 1 | 1µH | _Inductors_GRZ:IHLP2525CZ | L1 |
| 1 | 2.2µF | _Capacitors_GRZ:C_0603 | C12 |
| 1 | 3.3k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 33k | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C22 |
| 1 | 470nF | _Capacitors_GRZ:C_0603 | C7 |
| 1 | 47k | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 47nF | Capacitor_SMD:C_0603_1608Metric | C_{F}1 |
| 1 | 56k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 68k | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 82kΩ | _Resistors_GRZ:R_0603 | R31 |
| 1 | ACS713xLCTR-30A | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | ASAK | _Misc_GRZ:Osc_ASAK | X2 |
| 1 | ASCO | _Misc_GRZ:Osc_ASCO | X1 |
| 1 | Battery_18650 | Battery:BatteryHolder_Keystone_1042_1x18650 | BT1 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_3002_1x2032 | BT2 |
| 1 | Conn_01x07_Pin | _Connectors_GRZ:PicoBlade_53398-0771 | J12 |
| 1 | Conn_BAL | Connector_JST:JST_XH_S7B-XH-A_1x07_P2.50mm_Horizontal | J1 |
| 1 | Conn_BAT | Connector_AMASS:AMASS_XT60IPW-M_1x03_P7.20mm_Horizontal | J2 |
| 1 | DNP | _Resistors_GRZ:R_0603 | R33 |
| 1 | IP5506 | _IC_Misc_GRZ:IP5506 | IC1 |
| 1 | IRF8721PBF-1 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q1 |
| 1 | Jumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | LM3940IMP-3.3 | _Regulators_GRZ:LM3940IMP | IC2 |
| 1 | MicroSD_Connector_503182-1852 | _Connectors_GRZ:MicroSD_503182-1852 | J13 |
| 1 | OLED12864-I2C | _Modules_GRZ:OLED12864-I2C | M1 |
| 1 | STM32G484RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TMP101 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | USB-C_12pin | _Connectors_GRZ:USB-C_HRO_C-31-M-12 | J11 |
Similar boards
- 2 layers86 × 82 mm

- 2 layers98.8 × 60.7 mm

PIC soldering station
wonbinbk/SSS
Smart Soldering Station - for fake Hakko 907, using PIC16f87xA, PID heat controller with auto-standby and auto-power-off.
76 parts4GPL-3.0 - 2 layers70 × 89 mm

- 4 layers84.5 × 17 mm

SmartProbe v004
alex31/smartprobe
firmware and hardware for an autonomous five holes 3D pitot tube
90 parts1 - 4 layers53 × 35.2 mm

- 4 layers82.4 × 100 mm

- 4 layers87.7 × 52 mm

FoxFobz Reciever
edodso2/FoxFobz
A BLE key fob + receiver that adds keyless lock/unlock to classic cars, starting with the 1988 Fox-body Mustang.
69 parts - 4 layers111.8 × 59.1 mm

ControleurPulve
Mobilab-AgroTIC/debitdouille
Système pour controler le fonctionnement d'un pulvérisateur
107 parts
Questions
How big is the Battery tester PCB?
It measures 130 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Battery tester use?
132 parts, built around the TMP101NA, BTS7004-1EPP, LM3940IMP-3.3 and KP-1608SURC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Battery tester KiCad files?
From the Fabien-B/battery_tester repository on GitHub, at the commit this page was made from: the board is battery_tester.kicad_pcb and its schematic battery_tester.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Battery tester design in my own project?
Its repository states no licence, so its author keeps all rights: ask Fabien-B before reusing the design.