

Rpi gpib pico
GPIB interface for Raspberry Pi
- Size
- 65 × 45 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 121
- Pads
- 346
- Tracks, vias
- 763, 66
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 18 May 2019
- Updated
- 26 Feb 2022
Overview
Rpi gpib pico is an open-source printed circuit board by Elemecca, from the Elemecca/rpi-gpib repository on GitHub. It is a 2-layer board of 65 × 45 mm with 73 parts on 121 nets, routed with 763 tracks and 66 vias.
It is built around the RP2040, SN75160BDW and SN75162BDW, with the W25Q128JVSIQ, CAT24C32LI- and BAT54C among its other parts. Its parts include 23 resistors, 20 capacitors, 9 diodes, 6 ICs and 4 connectors. It belongs with the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)SN75160BDW
SOIC-20-300mil0℃~+70℃ 1 20ns@5V,15pF 4.75V~5.25V 48mA 5.2mA 8 Bidirectional Open-drain SOIC-20 Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversSN75162BDW
SOIC-24-300mil0℃~+70℃ 1 20ns@5V,15pF 4.75V~5.25V 48mA 5.2mA 8 Bidirectional Power-off isolation、Output enable Schmitt trigger Tri-State SOIC-24-300mil Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, TransceiversW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHCAT24C32LI-
PDIP-8-40℃~+85℃ 1,000,000 cycles 1.7V~5.5V 100 Years 1MHz 2mA 3.5us 32Kbit 5ms 5uA Hardware write protection function、Noise suppression function、Built-in power-on reset (POR) I2C PDIP-8 EEPROM ROHSonsemiEEPROMBAT54C
SOT-231 Pair Common Cathode 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-23 Schottky Diodes ROHSNexperiaSchottky Diodes12M10PI/XT324-10/20
SMD3225-4P-40℃~+85℃ 100Ω 10pF 12MHz ±10ppm ±20ppm SMD3225-4P Crystals ROHSYICCrystals
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R20, R21, R22, R23, R24, R25, R26, R27, R30, R31, R32, R33, R34, R35, R36 +2 |
| 14 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C10, C11, C12, C15, C18, C19, C20 |
| 8 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D20, D21, D22, D23, D24, D25, D26, D27 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP4, TP5 |
| 4 | MountingHole | local:MountingHole_RPi_HAT | H1, H1, H1, H2 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C13, C14 |
| 2 | 10u | Capacitor_SMD:C_0402_1005Metric | C16, C17 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C8, C9 |
| 2 | 27R4 | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 3k9 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 12M10PI/XT324-10/20 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | CAT24C32 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | Debug | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | GPIB | local:NorComp_112-024-113R001 | J1 |
| 1 | LOGO | local:OSHW | OSHW |
| 1 | MMBZ5222BLT1G | Package_TO_SOT_SMD:SC-59 | D28 |
| 1 | NCP1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | RP2040 | local:RP2040-QFN-56 | U1 |
| 1 | RasPi_Header_40W | local:PinSocket_2x20_P2.54mm_Vertical_Centered_Anchor | J3 |
| 1 | SN75160BDW | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U2 |
| 1 | SN75162BDW | Package_SO:SOIC-24W_7.5x15.4mm_P1.27mm | U3 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Amphenol_10118194_Horizontal | J2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U4 |
More from Elemecca/rpi-gpib
2- 2 layers65 × 30 mm

- 2 layers15.7 × 95.3 mm

Similar boards
- 2 layers63.5 × 55.6 mm

AR488-common
douardda/ESP32-GPIB-pcb
GitHub mirror of the PCB design for an ESP32/Arduino based GPIB interface
11 parts9 - 2 layers33 × 57.4 mm

CareLite V122
OpenhimerLab/CareLite-GPIB
CareLite is an open-source, tiny, small USB-GPIB adaptor based on STM32 with temperature sensors.
37 parts9GPL-3.0 - 2 layers63 × 65.7 mm

Wifi GPIB
bitdivision/GPIB-wifi-pcb
A GPIB adapter using an ESP8266 for wifi functionality and a Cortex M0.
113 parts4 - 2 layers55.1 × 54.9 mm

- 2 layers66.2 × 60.9 mm

- 4 layers70 × 69.8 mm

- 6 layers40 × 40 mm

Integrated FOC Stepper Driver
chpaxson/Echo-Telepresence
UC Berkeley ME 135/235 Spring 2025 Term Project
77 parts2 - 4 layers152.4 × 63.5 mm

Questions
How big is the Rpi gpib pico PCB?
It measures 65 × 45 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rpi gpib pico use?
73 parts, built around the RP2040, SN75160BDW, SN75162BDW and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rpi gpib pico KiCad files?
From the Elemecca/rpi-gpib repository on GitHub, at the commit this page was made from: the board is board/rpi-gpib-pico/rpi-gpib-pico.kicad_pcb and its schematic board/gpib-breakout/gpib-breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rpi gpib pico design in my own project?
Its repository states no licence, so its author keeps all rights: ask Elemecca before reusing the design.