
VeinFinder Thruhole LedBoard
ElectronicCats/Vein-Finder
A reliable, easy-to-make and open source device!

A reliable, easy-to-make and open source device!
VeinFinder SMDLedBoard is an open-source printed circuit board by ElectronicCats, from the ElectronicCats/Vein-Finder repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 60 × 66.2 mm with 43 parts on 25 nets, routed with 183 tracks and 23 vias.
Its parts include 20 resistors, 20 diodes and 1 connector.
A reliable, easy-to-make and open source device!
In the healthcare field, nursing staff frequently encounter difficulties when inserting a peripheral intravenous catheter (PIVC) into patients. Various factors can make it challenging to establish IV access, such as age, weight, hydration status, and even skin tone of the extremities. Often, a single puncture is unsuccessful, causing patient distress and increasing the risk of infection or trauma.
This is a device that, using LEDs, helps to contrast veins through the skin, making them visible, even those that are not deep, but also not the superficial ones that we observe with the naked eye. This is achieved thanks to hemoglobin, which absorbs the light that attempts to pass through the veins, making them visible.
Our design was mainly based on three different sources that will be linked below, all credit to the original authors. We focused our research on amount of LEDs and LED wavelength. We found numbers ranging from 8 to 30 LEDs. We decided to go with 20 LEDs for our design, it was the average. As for the wavelength we found that the colors that covered the widest range of skin tones were red and amber. The red LEDs had a dominant wavelength of 625 nm and the orange LEDs of 610 nm. We decided to go with 10 red and 10 amber LEDSs. We used PWM signals to give each color a 5 steps of brightness for better control.
RESEARCH ON VEIN FINDER INSTRUMENT DESIGN USING TWOWAVELENGTH OPTICAL METHOD
PROTOTIPO DE FACILITADOR DE CANALIZACIÓN
Design of vein finder with multi tuning wavelength using RGB LED
The testing was done internally only. We asked different people from the office with different skin tones and checked if their veins were visible using the device.
The LEDs on the boards, as any other LED, can cause damage to the eye if they are looked at for prolonged periods of time. The device is a prototype and is not water or debris/dust proof.


Contributions are welcome!
Please read the document Contribution Manual which will show you how to contribute your changes to the project.
✨ Thanks to all our contributors! ✨
See Electronic Cats CLA for more information.
See the community code of conduct for a vision of the community we want to build and what we expect from it.
Electronic Cats invests time and resources providing this open-source design, please support Electronic Cats and open-source hardware by purchasing products from Electronic Cats!
Designed by Electronic Cats.
Firmware released under an GNU AGPL v3.0 license. See the LICENSE file for more information.
Hardware released under an CERN Open Hardware Licence v1.2. See the LICENSE_HARDWARE file for more information.
Electronic Cats is a registered trademark, please do not use if you sell these PCBs.
Oct 2024
| Qty | Value | Footprint | References |
|---|---|---|---|
| 20 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20 +4 |
| 1 | Conn_01x03_MountingPin | Connector_JST:JST_SH_BM03B-SRSS-TB_1x03-1MP_P1.00mm_Vertical | J3 |
| 1 | ORAN1 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | ORAN10 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D20 |
| 1 | ORAN2 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | ORAN3 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D6 |
| 1 | ORAN4 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D8 |
| 1 | ORAN5 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D10 |
| 1 | ORAN6 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D12 |
| 1 | ORAN7 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D14 |
| 1 | ORAN8 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D16 |
| 1 | ORAN9 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D18 |
| 1 | RED1 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | RED10 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D19 |
| 1 | RED2 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | RED3 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D5 |
| 1 | RED4 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7 |
| 1 | RED5 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D9 |
| 1 | RED6 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D11 |
| 1 | RED7 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D13 |
| 1 | RED8 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D15 |
| 1 | RED9 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D17 |
The 41 most common of 43 parts.

ElectronicCats/Vein-Finder
A reliable, easy-to-make and open source device!

ElectronicCats/Vein-Finder
A reliable, easy-to-make and open source device!

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards

rusefi/rusefi
rusefi - GPL internal combustion engine control unit


jrsteensen/OpenHornet
OpenHornet 1:1 F/A-18C Simulator Repository


tebl/RC6502-Apple-1-Replica
An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

nodestark/mdb-esp32-cashless
ESP32-based MDB cashless device for vending machines, supporting EVA DTS DEX/DDCMP telemetry and payments over the MDB protocol via Bluetooth and MQTT

zynthian/zynthian-hw
Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...
It measures 60 × 66.2 mm and has 2 copper layers, 1.6 mm thick.
43 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ElectronicCats/Vein-Finder repository on GitHub, at the commit this page was made from: the board is hardware/VeinFinder_SMDLedBoard/VeinFinder_SMDLedBoard.kicad_pcb and its schematic hardware/VeinFinder_ControlBoard/VeinFinder_ControlBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).