

Carte Base roulante 2024
- Size
- 68 × 84 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 79
- Pads
- 275
- Tracks, vias
- 609, 125
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 16 Nov 2023
- Updated
- 13 Feb 2025
Overview
Carte Base roulante 2024 is an open-source printed circuit board by ENACRobotique, from the ENACRobotique/Cartes_Base_roulante repository on GitHub. It is a 2-layer board of 68 × 84 mm with 71 parts on 79 nets, routed with 609 tracks and 125 vias.
It is built around the R-78E5.0-1.0, IRF7424 and LM3940IMP-3.3, with the LSM6DSL among its other parts. Its parts include 24 capacitors, 10 resistors, 5 diodes, 4 ICs and 1 transistor. It belongs with the STM32 boards of this library.
Main components
4R-78E5.0-1.0
SIP,11.6x7.5mm-40℃~+85℃ 1 10.2mm 11.6mm 1A 2200uF 300uA 50mVp-p 5V 7.5mm 7V~36V 850kHz 94% Short Circuit Protection、Automatic fault recovery Step-down type ±3% SIP,11.6x7.5mm DC-DC Power Modules ROHSYLPTECDC-DC Power ModulesIRF7424
SOIC8-30V -11A P-Channel HEXFET® Power MOSFETInfineon TechnologiesUncategorisedLM3940IMP-3.3
SOT-223-40℃~+125℃@(Tj) 1 10mA 1A 250uVrms 3.3V 5.5V 500mV@(1A) Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLSM6DSL
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 3uA 4KB IMU (accelerometer + gyroscope) Motion event detection、Synchronization and timestamp SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSSTMicroelectronicsAccelerometers
README
README.mdCarte_Base_roulante_2024
Carte custom pour une base roulante holonome basé sur la STM32G484Retx Conçue pour d'elle même faire de l'odométrie par encodeur et gyroscope. Le debug nécéssite une sonde externe.
Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C3, C5, C7, C8, C9, C10, C14, C16, C17, C18 |
| 5 | 10u | Capacitor_SMD:C_0603_1608Metric | C20, C21, C22, C23, C24 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP_CS1, TP_GND1, TP_MISO1, TP_MOSI1, TP_SCK1 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100u | Capacitor_SMD:CP_Elec_10x12.5 | C2, C4, C6 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R4 |
| 3 | osef | Resistor_SMD:R_0805_2012Metric | R5, R6, R10 |
| 3 | ~ | ENAC_robotique:IFX9201SG | U2, U3, U6 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C13, C15 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | D | Diode_SMD:Nexperia_CFP3_SOD-123W | D2, D3 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 40K | Resistor_SMD:R_0805_2012Metric | R9 |
| 1 | 470n | Capacitor_SMD:C_0603_1608Metric | C19 |
| 1 | 53k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | ALIM | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | ALIM1 |
| 1 | ASCO | ENAC_robotique:Osc_ASCO | QUARTZ1 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | UART4 |
| 1 | DEBUG | Connector_Molex:Molex_CLIK-Mate_502382-0570_1x05-1MP_P1.25mm_Vertical | DEBUG1 |
| 1 | D_Zener | Diode_SMD:D_SOD-523 | ZENER1 |
| 1 | ENC1 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | ENC 1 |
| 1 | ENC2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | ENC 2 |
| 1 | ENC3 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | ENC 3 |
| 1 | IRF7424 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q2 |
| 1 | LED1 | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | LED1 |
| 1 | LED2 | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | LED2 |
| 1 | LED_ALIM | LED_SMD:LED_0603_1608Metric | D5 |
| 1 | LM3940IMP-3.3 | ENAC_robotique:LM3940IMP | Transfo5->3.3 |
| 1 | LOGO | library:logo | G*** |
| 1 | LOGO | ENAC_robotique:logo_enac_moyen | G*** |
| 1 | LSM6DSL | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | IMU1 |
| 1 | MOT1 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | locked |
| 1 | MOT2 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | locked |
| 1 | MOT3 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | locked |
| 1 | R-78E5.0-1.0 | Converter_DCDC:Converter_DCDC_RECOM_R-78E-0.5_THT | Transfo18->5 |
| 1 | STM32G484RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SW_Push | ENAC_robotique:SWITCH_DTSM31NV | SWITCH1 |
| 1 | USB-C_12pin | ENAC_robotique:USB-C_HRO_C-31-M-12 | USB-C1 |
More from ENACRobotique/Cartes_Base_roulante
1- 2 layers100 × 157 mm

Similar boards
- 2 layers76 × 68 mm

- 2 layers75 × 69 mm

- 2 layers50 × 50 mm

- 2 layers55 × 69.5 mm

- 2 layers39.6 × 49.8 mm

- 2 layers130 × 100 mm

- 4 layers136.5 × 136 mm

- 2 layers

Questions
How big is the Carte Base roulante 2024 PCB?
It measures 68 × 84 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Carte Base roulante 2024 use?
71 parts, built around the R-78E5.0-1.0, IRF7424, LM3940IMP-3.3 and LSM6DSL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Carte Base roulante 2024 KiCad files?
From the ENACRobotique/Cartes_Base_roulante repository on GitHub, at the commit this page was made from: the board is MCC/Carte_Base_roulante_2024.kicad_pcb and its schematic Brushless/CarteBrushless.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Carte Base roulante 2024 design in my own project?
Its repository states no licence, so its author keeps all rights: ask ENACRobotique before reusing the design.