
BenchyMotherBoard AM625
Daxxn/BenchyReloaded
New and improved Benchy, now with more doodads!

New and improved Benchy, now with more doodads!
BenchyFrontPanel is an open-source printed circuit board by Daxxn, from the Daxxn/BenchyReloaded repository on GitHub, published under the AGPL-3.0 licence. It is a 2-layer board of 400 × 65 mm with 174 parts on 151 nets.
It is built around the TC7PZ17FU,LJ(CT, SN74HCS125BQAR and MCP23S08-E/ML, with the M2.5, TL3365AF180QG and TL3215AF160GQ among its other parts. Its parts include 48 resistors, 42 capacitors, 30 diodes, 22 switches and 12 ICs. It belongs with the STM32 boards of this library.
Alot of this is old and needs to be updated!
Your electronics workbench buddy! (Warning - Benchy is not actually your buddy and will probably try to kill you. It's hideously expensive, and way too time consuming to build!)
This design integrates an STM32MP1 Series micro processor (U2) with 8Gb DDR3 memory (U20). This adds a large amount of raw power internally. Taking alot of the load required to control the sub-systems from the users PC and adds more flexability to the system as a whole.
The main reason why I needed to design my own USB hub instead of stuffing an "off the shelf" hub up benchys trumpet was the absolute lack of protection circuitry in most "consumer grade" USB hubs. There is no back-feed protection, verry little to no current monitoring, and the bare minimum ESD and EMI protection. Thats just not acceptable! imagine my supprise when I cracked open an $85 hub from Amazon and, after blowing out a channel, found no power management at all. The cost of finding a hub that has these protections is going to be around the same price as designing and building my own. (Except for the time investment... but who cares about that?!?)
These features arent exaclty flashy, they dont look very good on a brochure. So they usually arent there. If they are, its just a bullet point. Often they just claim to conform to the USB spec. The lack protection doesn't actually conform to the spec at all. I will admit, some of the protection features are optional and not necessary for every day use. The problem is an electronics workbench is very mean. It will bully these simple hubs until they don't want to play along anymore.
Im using a quite extensive I2C bus system to communicate with the different boards and functional blocks. This cuts WAY down on the number of wires and pins required for the main controller and allows for better modularity within benchy.
Due to the size of the bus and the different devices, the bus is split by an I2C Mux to keep bus integrity while communicating to far PCBs.
The one thing that made the two different power supplies possible was the Switch-Mode Power Supply (SMPS) that was built into the DVR box that spawned this project. The output from the SMPS is a high-current 12V source and 30V source. This was easy to adapt to my needs.
The adjustable supply is built with help from Dave, (Thanks Dave!) using the LM317 adjustable regulator.
The ATX supply can provide 15 amps to the USB ports allowing each port to supply around 2 amps. Power is managed by the UCS2114s. Controlling both the current limit and backfeeding.
Fairly standard design using a MOSFET in its linear region, dissipating alot of energy. With the help of a big heatsink and a fan, it can be used to load power supplies to test their response. The current shunt will allow for precise measurement of power usage. Control is linked to the main microcontroller on the the motherboard. Allowing full control.
Low voltage volt meters with moderate accuracy and speed. Designed to measure multiple voltage levels simultaneously. This is helpful for testing power supplies designed for advanced ICs that require lots of voltages to run. Such as Processors, FPGAs, and PC Motherboards.
Creates sine, square, and triangle waves. from ~100Hz to ~100KHz.
8 channel relay block used to control general things around the bench like lighting and other small devices. Rated for mains voltage but not for high current.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 40 | 100n | Daxxn_Standard_Capacitors:CAP_0402 | C1, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24 +24 |
| 17 | 100K | Daxxn_Standard_Resistors:RES_0402 | R11, R14, R16, R18, R19, R20, R21, R23, R27, R31, R32, R36, R37, R38, R39, R48 +1 |
| 16 | 10K | Daxxn_Standard_Resistors:RES_0402 | R1, R2, R5, R6, R15, R33, R34, R35, R40, R41, R42, R43, R44, R45, R46, R47 |
| 11 | M2.5 | MountingHole:MountingHole_2.7mm_M2.5_ISO7380_Pad | H1, H2, H3, H4, H5, H6, H7, H8, H9, H10, H11 |
| 9 | CZ1-0603-BLUE | Daxxn_LEDs:LED_0603_1608Metric | D3, D7, D8, D11, D15, D18, D19, D22, D24 |
| 8 | 1K3 | Daxxn_Standard_Resistors:RES_0402 | R3, R4, R12, R17, R22, R24, R25, R26 |
| 8 | CZ2-0603-GREEN | Daxxn_LEDs:LED_0603_1608Metric | D2, D5, D6, D13, D14, D21, D28, D30 |
| 8 | TL3365AF180QG | Daxxn_Controls_Buttons:TL3365AF180QG | SW5, SW14, SW15, SW17, SW18, SW19, SW20, SW21 |
| 7 | TL3215AF160BQ | Daxxn_Controls_Buttons:TL3215A | SW3, SW4, SW7, SW8, SW9, SW10, SW12 |
| 6 | CZ3-0603-ORANGE | Daxxn_LEDs:LED_0603_1608Metric | D1, D4, D12, D20, D25, D26 |
| 5 | CZ5-0603-RED | Daxxn_LEDs:LED_0603_1608Metric | D9, D10, D16, D17, D23 |
| 3 | 2K2 | Daxxn_Standard_Resistors:RES_0402 | R28, R29, R30 |
| 3 | MCP23S08-E/ML | Daxxn_Packages:QFN-20-1EP_4x4mm_P0.5mm_EP2.7x2.7mm | U4, U5, U8 |
| 3 | SN74HCS365PWR | Daxxn_Packages:TSSOP-16_4.4x5mm_P0.65mm | U9, U10, U11 |
| 2 | 10n | Daxxn_Standard_Capacitors:CAP_0402 | C2, C3 |
| 2 | 2K94 | Daxxn_Standard_Resistors:RES_0402 | R10, R13 |
| 2 | 4K7 | Daxxn_Standard_Resistors:RES_0402 | R7, R8 |
| 2 | CZ8-0603-YLW-GREEN | Daxxn_LEDs:LED_0603_1608Metric | D27, D29 |
| 2 | STP16CP05MTR | Daxxn_Packages:SOIC-24W_7.5x15.4mm_P1.27mm | U2, U3 |
| 2 | TC7PZ17FU,LJ(CT | Daxxn_Packages:SOT-363_SC-70-6 | U6, U7 |
| 2 | TL3215AF160GQ | Daxxn_Controls_Buttons:TL3215A | SW6, SW13 |
| 1 | 228CMVARGBFR | Daxxn_Controls_Buttons:228C | SW16 |
| 1 | 5019514500 | Daxxn_Connectors_FFC:5019514500 | J2 |
| 1 | 74LVC3G17GS,115 | Daxxn_Packages:X2SON-8_1.4x1mm_P0.35mm | U1 |
| 1 | B3W-9000-RG2N | Daxxn_Controls_Buttons:B3W-9000 | SW2 |
| 1 | BOJACK-BTN-6X6X5-2 | Daxxn_Controls_Buttons:BOJACK-BTN-6x6x5 | S1 |
| 1 | JS1400AFQ | Daxxn_Controls_Navigation:JS1400 | SN1 |
| 1 | PEC11R-4220F-S0024 | Daxxn_Controls_Encoders:PEC11R | EN1 |
| 1 | RIGOL-LA-PROBE | Daxxn_Connectors_PCI:10018784-10200TLF | J1 |
| 1 | SN74HCS125BQAR | Daxxn_Packages:WQFN-14_B3x2.5mm_P0.5mm | U12 |
| 1 | TL3215AF160RQ | Daxxn_Controls_Buttons:TL3215A | SW1 |
| 1 | TL3215AF160YQ | Daxxn_Controls_Buttons:TL3215A | SW11 |
| 1 | TP-12V | TestPoint:TestPoint_Pad_D2.0mm | TP6 |
| 1 | TP-VCC-STBY | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | TP-VCC-USB | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | TP-VDD | TestPoint:TestPoint_Pad_D2.0mm | TP7 |
| 1 | TP-VDD-SYS | TestPoint:TestPoint_Pad_D2.0mm | TP4 |

Daxxn/BenchyReloaded
New and improved Benchy, now with more doodads!

Daxxn/BenchyReloaded
New and improved Benchy, now with more doodads!

Daxxn/BenchyReloaded
New and improved Benchy, now with more doodads!


Daxxn/BenchyReloaded
New and improved Benchy, now with more doodads!



a3-audio/a3-motion
The 4-channel motion sampler of A³ Audio. It records movements on a touchscreen sphere and plays them back in time with the beat, steering each channel's position on A³ Core over OSC.


es-ude/elasticai.hardware
Schematics and Board design for ElasticNodeHardware

LRNATHD/CH572D-Board
example board using WCH's CH572 Bluetooth microcontroller

Deivid-Negoita/octobot
An eight-legged walking robot I built end to end: chassis CAD, a 24-servo ATmega32U4 controller board, the firmware, and a browser IK workbench you can drive it from.

williamjroche/Drone_Flight_Controller
This is a GPS-Denied Autonomous Drone that uses computer vision to fly with radio transmission override. Autonomy is a work in progress.
It measures 400 × 65 mm and has 2 copper layers, 1.6 mm thick.
174 parts, built around the TC7PZ17FU,LJ(CT, SN74HCS125BQAR, MCP23S08-E/ML and M2.5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Daxxn/BenchyReloaded repository on GitHub, at the commit this page was made from: the board is FrontPanel/BenchyFrontPanel/BenchyFrontPanel.kicad_pcb and its schematic ELoad/BenchyELoad/BenchyELoad.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the AGPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).