

AkiraFlex
RDRAM Termination Flex PCB for N64 Portables
- Size
- 26.2 × 8.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 26
- Nets
- 15
- Pads
- 51
- Tracks, vias
- 34, 4
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 8 May 2024
- Updated
- 18 Aug 2024
Overview
AkiraFlex is an open-source printed circuit board by CrazyGadgetMods, from the CrazyGadgetMods/AkiraFlex repository on GitHub. It is a 2-layer board of 26.2 × 8.8 mm with 26 parts on 15 nets, routed with 34 tracks and 4 vias.
README
README.mdAkiraFlex
AkiraFlex is an N64 RDRAM termination flex PCB, designed to be a low-profile replacement for the stock expansion port + trimmed jumper pak combo commonly used in existing N64 portables. It was inspired by the "Akira Method" of digging up the expansion port pads and deadbugging the RDRAM termination circuit.
Installation
Components for the flex can either be pulled from an original N64 jumper / expansion pak, or can be bought brand new. All RAs are 1206-sized 51 Ohm, all caps are 0603-sized 1uF.
This flex was originally designed around a NUS-CPU-03 board, which has test points on the RDRAM traces between the RAM and the expansion port. If you are using this on a non-Rev 3 board (such as the Rev 4 board I installed in on here), you will need to scratch the traces as shown. Additionally, the VREF and VTERM vias must be scratched / tinned. Though apparently not necessary according to some testing Cy (of the BitBuilt Forums) has done, it is best practice to dig up the existing expansion port pads, as they will act as stubs for the RDRAM; not digging them up may lead to the board not booting / possible instabilities in-game. Once all the necessary vias / traces have been scratched / tinned / dug up, the flex can be installed on the board. Once installed, run a magnet wire from the pad shown below and the bottom of R33 on the N64 (rambus clock output from the mx8330).

Testing
Purchasing
If interested in purchasing an AkiraFlex kit (blank flex + RAs and capacitors), I am selling them on my Etsy store!
Credits
- Akira: creating the original method for deadbugging the RDRAM termination circuit
- Noah: inspiration from his unfinished Terminator 64 flex
- Cy: inspiration from his Terminator 64 flex
- YveltalGriffin: answering my many, many, many questions during my N64 anatomy deep-dive and helping me understand RDRAM / the Akira Method
- BitBuilt: Being the best modding community out there!
License
Solderpad Hardware License v2.1
Parts
26| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | TestPoint | Library:RAM Via | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP18 |
| 4 | C | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4 |
| 3 | R_Network04 | Library:R_Array_Concave_4x0603 | RN1, RN2, RN3 |
| 3 | TestPoint | Library:RAM Via 2 | TP15, TP16, TP17 |
| 2 | TestPoint | Library:RAM GND | TP13, TP14 |
The 25 most common of 26 parts.
Similar boards
- 2 layers57.3 × 19 mm

- 2 layers98 × 59.5 mm

MCP23017 PCB
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
26 parts915 - 2 layers142.9 × 98.5 mm

- 2 layers86.1 × 86.1 mm

- 2 layers103.8 × 50 mm

Galagino pcb set
harbaum/galagino
A Galaga, Pac-Man and Donkey Kong arcade emulator for the ESP32
26 parts558 - 2 layers20.3 × 34.8 mm

L0 ESP32
Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.
26 parts546MIT - 2 layers40.6 × 50.8 mm

WALTsm
google/walt
A device for measuring latency of physical sensors and outputs on phones and computers
26 parts474Apache-2.0 - 2 layers158.5 × 75 mm

Questions
How big is the AkiraFlex PCB?
It measures 26.2 × 8.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the AkiraFlex use?
26 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the AkiraFlex KiCad files?
From the CrazyGadgetMods/AkiraFlex repository on GitHub, at the commit this page was made from: the board is KiCAD/AkiraFlex.kicad_pcb and its schematic KiCAD/AkiraFlex.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the AkiraFlex design in my own project?
Its repository states no licence, so its author keeps all rights: ask CrazyGadgetMods before reusing the design.