Skip to the content
2 layers67 × 48 mmIgnition system, the printed circuit board in 3D

A solid-state, remote ignition system designed for experimental rocketry. Built for the Dragons Space Team to safely and reliably ignite rocket motors (like Estes Viking) using electronic matches.

Size
67 × 48 mm
Copper layers
2
Thickness
1.6 mm
Parts
33
Nets
69
Pads
191
Tracks, vias
484, 109
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
9 May 2026
Updated
14 Oct 2026

Overview

Ignition system is an open-source printed circuit board by AyrXZ47, from the AyrXZ47/dst-ignition-system repository on GitHub. It is a 2-layer board of 67 × 48 mm with 33 parts on 69 nets, routed with 484 tracks and 109 vias.

It is built around the TP4056-42-ESOP8. Its parts include 10 resistors, 3 switches and 2 capacitors. It belongs with the robots and motor control boards and the RP2040 boards of this library.

Main components

1

README

README.md

🚀 DST Ignition System

License: Apache 2.0 Hardware License: CERN-OHL-P-2.0

A solid-state, remote ignition system designed for experimental rocketry. Built for the Dragons Space Team to safely and reliably ignite rocket motors (like Estes Viking) using electronic matches.

🧠 System Architecture

  • Microcontroller: Raspberry Pi Pico (RP2040)
  • Firmware: Rust 🦀 with Embassy — planned, not implemented yet (see Hardware status)
  • Telemetry & Comms: LoRa (SX1278 RA-02, single transceiver — TX/RX role is firmware-side, half-duplex)
  • Power Switching: Logic-Level N-Channel MOSFET (AOD4184A)

📂 Repository Structure

  • /hardware/: KiCad project files (Schematics and PCB layouts).
  • /src/: Rust source code for the RP2040 firmware.
  • /docs/: Pinout diagrams, component datasheets, and operation manuals.

🛠️ Getting Started

Firmware (Rust)

⚠️ Not available yet. The src/ directory is empty: the Rust/Embassy firmware is planned but has not been written. The steps below are reserved for when it lands:

  1. Install Rust and the thumbv6m-none-eabi target: rustup target add thumbv6m-none-eabi
  2. Install elf2uf2-rs for easy flashing: cargo install elf2uf2-rs --locked
  3. Build and run: cargo run --release

Hardware

Open the project in KiCad 10.x (KiCad 9.x also fine) located in the /hardware/ directory.

📋 Hardware status

Schematics and PCB live in /hardware/Kicad/ignition-system/. Current status (wave 3, in progress — see docs/design-notes.md for the full design reference):

  • Schematic: RP2040 (Pico) + TP4056 Li-ion charger (TEMP via external NTC 10k B3950, TH1) + AOD4184A N-MOSFET ignition switch + SX1278 RA-02 socket (2× 1×08 headers: SPI + control rows) + I2C display + status LEDs + master power switch SW3 (battery → SW3 → VSYS; the pack charges with the board off). ERC: 0 errors / 0 warnings.
  • PCB: placement in progress, not routed (agentes solo verifican con kicad-cli). DRC findings pending wave-3 fixes; see design-notes §5.
  • Firmware: src/ is empty; no Rust/Embassy code exists yet.
  • Next: wave 2 SPICE validation of the MOSFET gate margin (3.3V vs Vto 2.61V).

Parts

33
QtyValueFootprintReferences
5LEDLED_SMD:LED_0805_2012MetricBLED1, CHRG1, RLED1, STDBY1, YLED1
310kResistor_SMD:R_0805_2012MetricR5, R6, R7
3330Resistor_SMD:R_0805_2012MetricR1, R2, R3
210ufCapacitor_SMD:C_0805_2012MetricC1, C2
21kResistor_SMD:R_0805_2012MetricR8, R9
2Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalLORA-Sx1278(A)1, LORA-Sx1278(B)1
2SW_SPDTButton_Switch_THT:SW_E-Switch_EG1224_SPDT_AngledSW2, SW3
12.2kResistor_SMD:R_0805_2012MetricR4
1220Resistor_SMD:R_0805_2012MetricR11
1Conn_01x02Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalInBatt1
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalDisplay1-SSD1306
1NMOSPackage_TO_SOT_SMD:TO-252-2AOD4184A1
1NTC 10k B3950Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalTH1
1RaspberryPi_PicoModule:RaspberryPi_Pico_Common_UnspecifiedRaspberryPi_Pico1-RP2040
1SW_PushConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalSW1
1Screw_Terminal_01x02TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mmIGNITOR1
1TP4056-42-ESOP8Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalViasModuloDeCarga1

The 29 most common of 33 parts.

Similar boards

  • 2 layers60 × 111.3 mmSilkscreen pcb, the printed circuit board in 3D

    Silkscreen pcb

    iandchasse/silkscreen-pcb

    Silkscreen: open-hardware ESP32-S3 e-paper reader mainboard (KiCad 9). Formerly the de-link hub.

    189 parts589CERN-OHL-S-2.0
  • 2 layers96.8 × 91.4 mmInkbadge, the printed circuit board in 3D

    Inkbadge

    cheyao/inkbadge

    Undercity eink PCB badges controlled by a rp2350

    98 parts22
  • 2 layers51 × 21 mmFOX JACK EXT BOARD TOP, the printed circuit board in 3D

    FOX JACK EXT BOARD TOP

    KaliAssistant/Fox-Jack

    Portable social-engineering LAN tool for automated payloads and wired audits — based on Luckfox Pico Max

    35 parts22GPL-3.0
  • 2 layers31.3 × 67 mmRPBoard², the printed circuit board in 3D

    RPBoard²

    euvalennn/rpboard-squared

    Simple RP2350-based devboard

    63 parts9
  • 4 layers88 × 58 mmECG V-0.2, the printed circuit board in 3D

    ECG V-0.2

    Doenec/ecg-esp32

    open source project ecg with esp32 and ad8232

    115 parts8
  • 2 layers210 × 31 mmTrhw, the printed circuit board in 3D

    Trhw

    nimitvijayvargee/trhw

    This is an RP2040 ruler that implements wifi, bluetooth, BLE along with a 4MB Flash storage, LEDs, Input buttons and some cool units and lengths!

    59 parts8
  • 2 layers78 × 36 mmBt nes advantage pcb, the printed circuit board in 3D

    Bt nes advantage pcb

    cajunpanda/bluetooth-nes-advantage

    A bluetooth mod for the NES Advantage classic controller.

    45 parts7MIT
  • 2 layers61 × 61 mmESP32 FC, the printed circuit board in 3D

    ESP32 FC

    MAATHES-THILAK-K/ESP32-S3_FLIGHT_CONTROLLER

    A custom-designed flight controller based on the ESP32-S3 module, built for compatibility with the esp-fc firmware and Betaflight-like configuration.

    69 parts7Apache-2.0

Questions

How big is the Ignition system PCB?

It measures 67 × 48 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ignition system use?

33 parts, built around the TP4056-42-ESOP8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ignition system KiCad files?

From the AyrXZ47/dst-ignition-system repository on GitHub, at the commit this page was made from: the board is hardware/Kicad/ignition-system/ignition-system.kicad_pcb and its schematic hardware/Kicad/ignition-system/ignition-system.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ignition system design in my own project?

Its repository states no licence, so its author keeps all rights: ask AyrXZ47 before reusing the design.