

Launch Adapter
- Size
- 80.3 × 142.5 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 92
- Nets
- 125
- Pads
- 333
- Tracks, vias
- 335, 46
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 26 May 2022
- Updated
- 22 Aug 2022
Overview
Launch Adapter is an open-source printed circuit board by Alexandr-Filatov, from the Alexandr-Filatov/Hydrogen-PCB-LaunchBoard repository on GitHub. It is a 4-layer board of 80.3 × 142.5 mm with 92 parts on 125 nets, routed with 335 tracks and 46 vias.
It is built around the ISO1050DUB, LMV324 and DS90C401M, with the BC817 and PVT412LSPBF among its other parts. Its parts include 42 resistors, 21 capacitors, 14 connectors, 7 diodes and 3 ICs. It belongs with the interfaces and adapters boards of this library.
Main components
5ISO1050DUB
SOP-8-2.54mm-55℃~+105℃ 1 1Mbps 2500 3V~5.5V 4.75V~5.25V 50kV/us Bus fault detection and protection、Fail-safe SOP-8-2.54mm Isolated CAN Transceivers ROHSTexas InstrumentsIsolated CAN TransceiversLMV324
SOP-14-40℃~+85℃ 1MHz 2.8dB 250nA 3V~5.5V 4 400V/ms 40mA 40uV/√Hz@1kHz 430uA 5nA 7mV Built-in compensation、ESD protection SOP-14 Operational Amplifier ROHSIDCHIPOperational AmplifierDS90C401M
SOIC-80 155.5Mbps 2 4.5V~5.5V Driver SOIC-8 LVDS ICsTexas InstrumentsLVDS ICsBC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)PVT412LSPBF
SMD-6P-40℃~+85℃ 1012Ω 120mA 2ms 35Ω 4kV 500us One normally open: 2A (SPST-NO) Overcurrent Protection SMD-6P Solid State Relays (MOS Output) ROHSInfineon TechnologiesSolid State Relays (MOS Output)
Parts
92| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R27, R28, R29, R30, R31, R32, R33, R34, R35, R36, R37, R38, R43, R44, R45 +1 |
| 5 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4, C7, C11, C20 |
| 4 | 0.27u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C21, C22, C23 |
| 4 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R11, R12, R50 |
| 4 | 10p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9, C17, C18, C19 |
| 4 | 10u | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C2, C3, C5, C6 |
| 4 | 1n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C14, C15, C16 |
| 4 | 49.9 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R14, R15, R51 |
| 4 | LED_Small | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4, D5, D6, D7 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 1.6k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R7, R9 |
| 3 | 120 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3 |
| 3 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R6, R8 |
| 2 | +5V | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J7, J14 |
| 2 | 500 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R20 |
| 2 | Current Measure | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J12, J13 |
| 1 | +15V | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J8 |
| 1 | +3.3V | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J9 |
| 1 | +5V_CAN | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J10 |
| 1 | 1.5k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R39 |
| 1 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R40 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16 |
| 1 | 60 | Resistor_SMD:R_1210_3225Metric_Pad1.30x2.65mm_HandSolder | R41 |
| 1 | ADC1 | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J1 |
| 1 | ADC2 | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J2 |
| 1 | ADM3490ExR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | DS90C401M | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | D3 |
| 1 | D_Small | Diode_SMD:D_SOD-323F | D2 |
| 1 | Driver | Connector_IDC:IDC-Header_2x07-1MP_P2.54mm_Latch_Vertical | J5 |
| 1 | GPIO | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J4 |
| 1 | ISO1050DUB | Package_SO:SOP-8_6.62x9.15mm_P2.54mm | U3 |
| 1 | Interfaces | Connector_Molex:Molex_Micro-Fit_3.0_43045-0800_2x04_P3.00mm_Horizontal | J11 |
| 1 | LMV324 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U5 |
| 1 | PVT412LSPBF | Package_DIP:DIP-6_W8.89mm_SMDSocket_LongPads | D1 |
| 1 | PWM | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J3 |
| 1 | Voltage measure | Connector_Molex:Molex_Micro-Fit_3.0_43045-0400_2x02_P3.00mm_Horizontal | J6 |
Similar boards
- 2 layers100 × 100 mm

- 2 layers100 × 100 mm

- 4 layers113.5 × 105.5 mm

Multistepper
eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32
243 parts208 - 4 layers127 × 165 mm

ECU
lflaherty/ev-ecu
Custom ECU (firmware and hardware) for Bespoke Electric Vehicles
258 parts13Apache-2.0 - 4 layers260 × 113 mm

- 2 layers100 × 50 mm

- 2 layers127 × 91.5 mm

Accumulator Board
formulaslug/fs-3-schematics
Electrical Design Repository for fs-3 schematics and PCBs
110 parts5 - 4 layers127 × 67.3 mm

Questions
How big is the Launch Adapter PCB?
It measures 80.3 × 142.5 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Launch Adapter use?
92 parts, built around the ISO1050DUB, LMV324, DS90C401M and BC817. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Launch Adapter KiCad files?
From the Alexandr-Filatov/Hydrogen-PCB-LaunchBoard repository on GitHub, at the commit this page was made from: the board is Launch-Adapter.kicad_pcb and its schematic Driver_Connector.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Launch Adapter design in my own project?
Its repository states no licence, so its author keeps all rights: ask Alexandr-Filatov before reusing the design.