

Gh80-3003
Open-sourced Cherry MX PCB using the Pi Pico (RP2040) for the Cherry G80 3001 line of keyboards. Stock keyboards shipped originally with Cherry MY switches.
- Size
- 444.1 × 145.3 mm
- Copper layers
- 2
- Thickness
- 1.2 mm
- Parts
- 362
- Nets
- 184
- Pads
- 1,234
- Tracks, vias
- 1,492, 60
- Pours
- 988
- Routed
- Yes
- KiCad
- KiCad 9.99 (file 20250513)
- Created
- 7 Feb 2026
- Updated
- 12 Feb 2026
Overview
Gh80-3003 is an open-source printed circuit board by Alectardy98, from the Alectardy98/PCB_G803003_reduxal repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 444.1 × 145.3 mm with 362 parts on 184 nets, routed with 1,492 tracks and 60 vias.
It is built around the RP2040, W25Q128JVSIQ and SRV05-4, with the XC6206-2.8V among its other parts. Its parts include 119 diodes, 18 capacitors, 13 resistors, 12 inductors and 11 connectors. It belongs with the RP2040 boards of this library.
Main components
4RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)XC6206-2.8V
SOT-23-3L-40℃~+85℃@(Ta) 1 1uA 2.8V 250mA 350mV@(30mA) 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSYONGYUTAIVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdGH80-3003 Reduxal
Open-sourced Cherry MX PCB using the Pi Pico (RP2040) for the Cherry G80 3001 line of keyboards. Stock keyboards shipped originally with Cherry MY switches.
Original Placement measurements taken from other open-sourced PCB designs. https://github.com/evyd13/gh80-series https://github.com/Gacathon/Chili
Production
Production files in the JLCPCB Folder
Firmware
Qmk/Vial Firmware in the firmware folder
Use at your own risk.
Parts
362| Qty | Value | Footprint | References |
|---|---|---|---|
| 119 | D_Small | Diode_SMD:D_SOD-123 | D1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D110, D111, D112, D113, D114 +103 |
| 103 | MX-NoLED | MX_Only:MXOnly-1U-NoLED | MX_0.0, MX_0.1, MX_0.2, MX_0.3, MX_0.4, MX_0.5, MX_0.6, MX_0.7, MX_0.9, MX_0.10, MX_1.1, MX_1.2, MX_1.3, MX_1.4, MX_1.6, MX_1.7 +87 |
| 29 | , , , , , , , , , , , , , , , +13 | ||
| 10 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C8, C9, C12, C13, C14, C15, C16, C17, C18 |
| 9 | LED | Alectardy98:CHERRY_MX_LED | L1-1, L2-1, L2-2, L3-1, L4, L5, L5, L5, L5 |
| 8 | MX-NoLED | MX_Only:MXOnly-1.25U-NoLED | MX_8.0, MX_10.0, MX_10.1, MX_10.5, MX_10.6, MX_10.7, MX_11.1, MX_11.6 |
| 7 | Conn_01x01 | TestPoint:TestPoint_Plated_Hole_D2.0mm | J1, J5, J6, J13, J14, J15, J55 |
| 6 | MX-NoLED | MX_Only:MXOnly-1.5U-NoLED | MX_4.0, MX_4.7, MX_10.0_1, MX_10.6_1, MX_10.7_1, MX_11.1_1 |
| 5 | 1k | Resistor_SMD:R_0805_2012Metric | R5, R6, R106, R107, R108 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric | C4, C6, C7, C11 |
| 4 | MX-NoLED | MX_Only:MXOnly-1U | MX_0.8, MX_2.9, MX_10.1_1, MX_11.6_1 |
| 3 | LED | LED_THT:LED_D3.0mm | L1, L2, L3 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R4, R7 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R8, R22 |
| 2 | 500mA | Fuse:Fuse_1206_3216Metric | F1, F2 |
| 2 | MX-NoLED | MX_Only:MXOnly-2U-VerticalStabilizers-NoLED | MX_5.10_1, MX_9.10_1 |
| 2 | MX-NoLED | MX_Only:MXOnly-2U-NoLED | MX_3.6_1, MX_10.9_1 |
| 2 | MX-NoLED | MX_Only:MXOnly-2.25U-NoLED | MX_6.7, MX_8.0_1 |
| 1 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 22 | Resistor_SMD:R_0805_2012Metric | R100 |
| 1 | Alectardy98 | Alectardy98:Alectardy98101 | J12 |
| 1 | Boot | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | SW1 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_Mallory_AST1109MLTRQ | BUZ1 |
| 1 | Conn_01x04_MountingPin | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J3 |
| 1 | LOGO | footprints:logo | G*** |
| 1 | LOGO | Alectardy98:al11 | G*** |
| 1 | MX-NoLED | MX_Only:MXOnly-2.75U-NoLED | MX_9.6_1 |
| 1 | MX-NoLED | MX_Only:MXOnly-1.75U | MX_6.0 |
| 1 | MX-NoLED | MX_Only:MXOnly-7U-NoLED | MX_10.3_1 |
| 1 | MX-NoLED | MX_Only:MXOnly-1.25U | MX_6.0_1 |
| 1 | MX-NoLED | MX_Only:MXOnly-ISO-ReversedStabilizers-NoLED | MX_6.7_1 |
| 1 | MX-NoLED | MX_Only:MXOnly-1.75U-NoLED | MX_9.6 |
| 1 | MX-NoLED | MX_Only:MXOnly-6.25U-NoLED | MX_10.3 |
| 1 | RP2040 | Alectardy98:RP2040-QFN-56 | U2 |
| 1 | SRV05-4 | marbastlib-various:SOT-23-6-routable | U3 |
| 1 | SWD | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J2 |
| 1 | USB_C | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U4 |
| 1 | XC6206 | Package_TO_SOT_SMD:SOT-23 | U5 |
The 347 most common of 362 parts.
Similar boards
- 2 layers253.3 × 113.3 mm

- 2 layers344.7 × 123.6 mm

- 2 layers103.2 × 107.2 mm

Blue team pad
fearherbs1/blue-team-pad
An open source macropad for the cyber security analyst.
82 parts6GPL-3.0 - 2 layers344.7 × 123.6 mm

- 2 layers347.7 × 125.4 mm

- 2 layers112 × 45 mm

- 2 layers74.8 × 99.8 mm

- 4 layers75 × 65 mm

Questions
How big is the Gh80-3003 PCB?
It measures 444.1 × 145.3 mm and has 2 copper layers, 1.2 mm thick.
What parts does the Gh80-3003 use?
362 parts, built around the RP2040, W25Q128JVSIQ, SRV05-4 and XC6206-2.8V. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gh80-3003 KiCad files?
From the Alectardy98/PCB_G803003_reduxal repository on GitHub, at the commit this page was made from: the board is PCB/gh80-3003.kicad_pcb and its schematic PCB/gh80-3003.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gh80-3003 design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).