
ESP32-C3-WROOM02 dev board
pushtiujeniya/ESP32-C3-WROOM02_dev-board
This project is a custom 2-layer development board designed around the ESP32-C3-WROOM-02 Wi‑Fi + Bluetooth MCU module.

A compact 4-layer ESP32 evaluation board designed in KiCad, focused on reliable power distribution, signal integrity, and ease of prototyping.
ESP32 C3 Mini is an open-source printed circuit board by Akshath2002, from the Akshath2002/ESP32-Mini-Evaluation-Board repository on GitHub. It is a 4-layer board of 29.4 × 39.3 mm with 29 parts on 29 nets, routed with 147 tracks and 23 vias.
It is built around the ESP32-C3-WROOM-02-H4, AP2112K-3.3 and USBLC6-2SC6, with the PESD5V0L1ULD among its other parts. Its parts include 10 capacitors, 9 resistors, 3 ICs, 3 connectors and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.
A compact 4-layer ESP32 evaluation board designed in KiCad, focused on reliable power distribution, signal integrity, and ease of prototyping.
USB D+ and D− differential pairs were routed with consistent spacing and a continuous ground reference plane to maintain signal quality and minimize impedance discontinuities.
VBUS and 3.3 V power rails utilize localized copper regions to reduce trace resistance and improve current delivery from the voltage regulator to the ESP32 module.
Ground stitching vias are placed around the board perimeter and near layer transitions to provide low-impedance return paths and improve electromagnetic compatibility.
High-frequency decoupling capacitors are placed as close as possible to the ESP32 power pins. The crystal oscillator and supporting circuitry are positioned to minimize noise coupling and maintain stable operation.
✅ PCB Layout Complete ✅ Design Verification Complete 🚧 Fabrication Pending 🚧 Hardware Bring-up and Firmware Development Planned
Open-source hardware project. See LICENSE file for details.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C9 |
| 4 | 10k | Resistor_SMD:R_01005_0402Metric | R4, R5, R8, R9 |
| 3 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5, C6, C10 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1, SW2 |
| 2 | TBD | Capacitor_SMD:C_0201_0603Metric | C7, C8 |
| 2 | ~ | Connector_PinHeader_2.00mm:PinHeader_1x08_P2.00mm_Vertical | J2, J3 |
| 1 | 0R | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 100R | Resistor_SMD:R_01005_0402Metric | R6 |
| 1 | 5k1 | Resistor_SMD:R_01005_0402Metric | R2 |
| 1 | 5k1' | Resistor_SMD:R_01005_0402Metric | R1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | Crystal | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U3 |
| 1 | PESD5V0L1ULD | Diode_SMD:D_SOD-882D | D1 |
| 1 | TBD | Resistor_SMD:R_0201_0603Metric | R7 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |

pushtiujeniya/ESP32-C3-WROOM02_dev-board
This project is a custom 2-layer development board designed around the ESP32-C3-WROOM-02 Wi‑Fi + Bluetooth MCU module.

anasskrim61-wq/esp32-c3-mini
Custom ESP32-C3 Mini IoT hardware design and KiCad PCB project

NozomiNetworks/NN-antenna-manager
Open source project for a custom antenna manager for SDR cards

Benjpp/diy-stream-deck-pcb
PCB for hardware orchestrator from the diy stream deck

BhautikSarvaiya/ESP32_C3_MINI
This project focuses on designing a compact custom PCB based on the ESP32-C3 Mini microcontroller using KiCad 10.0.

d3ckerd/Custom-ESP32
Created a 4 layer custom esp32 dev board using the "ESP32-C3-WROOM-02" module. To learn much about how to create such a module I followed and learned from Pajopcb's youtube tutorials on the esp32.

diaseanodarren-hash/Custom-ESP32-C3-mini-Microcontroller
Designed a custom ESP32-C3-mini microcontroller development board from schematic capture and footprint creation to final PCB layout and trace routing.

It measures 29.4 × 39.3 mm and has 4 copper layers, 1 mm thick.
29 parts, built around the ESP32-C3-WROOM-02-H4, AP2112K-3.3, USBLC6-2SC6 and PESD5V0L1ULD. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Akshath2002/ESP32-Mini-Evaluation-Board repository on GitHub, at the commit this page was made from: the board is ESP32 C3 Mini.kicad_pcb and its schematic ESP32 C3 Mini.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Akshath2002 before reusing the design.