4 layers275 × 240 mm
2 layers75 × 74 mm
Clovece nezlob se PCB
AdamZatloukal/DMPČlověče nezlob se
- Size
- 75 × 74 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 32
- Nets
- 122
- Pads
- 240
- Tracks, vias
- 281, 136
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 29 Mar 2025
- Updated
- 30 Aug 2025
Overview
Clovece nezlob se PCB is an open-source printed circuit board by AdamZatloukal, from the AdamZatloukal/DMP repository on GitHub. It is a 2-layer board of 75 × 74 mm with 32 parts on 122 nets, routed with 281 tracks and 136 vias.
It is built around the STM32G071RBT6, LD1117S33TR(MS) and PJA3404_R1_00001, with the DCJ200-10-A-K1-K among its other parts. Its parts include 8 connectors, 7 resistors, 6 capacitors, 3 ICs and 2 diodes. It belongs with the STM32 boards of this library.
Main components
4
STM32G071RBT6
LQFP-64(10x10)-40℃~+85℃ 1.71V~3.6V 128KB 12bit 12bit 32 Bit 36KB 60 64MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
LD1117S33TR(MS)
SOT-223-20℃~+125℃@(Ta) 1 1.4V@(1A) 12V 1A 2mA 3.3V Fixed Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
PJA3404_R1_00001
SOT-23-55℃~+150℃ 1 N-channel 1.25W 2.1V 30V 343pF 34pF 45mΩ@4.5V 48pF 5.6A 7.8nC@10V N-Channel SOT-23 MOSFETs ROHSPANJIT InternationalMOSFETs
DCJ200-10-A-K1-K
插件-20℃~+70℃ 20V 2mm 5A 6.3mm DC Power Jack Right Angle 插件 DC Power Connectors ROHSGlobal Connector Technology (GCT)DC Power Connectors
README
readme.mdČlověče, nezlob se!
Interaktivní desková hra s možností hry s hráči řízenými algoritmem
Dokumentace k projektu se nachází zde
Vytvořeno ve spolupráci s:
✔️3. Místo KK SOČ
Parts
32| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.7mm_M2.5_Pad_Via | H1, H2, H3, H4 |
| 3 | 100R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R4, R5 |
| 3 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C6 |
| 3 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | J1, J2, J3 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R6 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R7 |
| 2 | 47u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C4 |
| 2 | Conn_02x19_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x19_P2.54mm_Vertical | J4, J6 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J7 |
| 1 | D | Diode_SMD:D_SMB_Handsoldering | D2 |
| 1 | DCJ200-10-A-K1-K | CAP:DCJ20010AK1K | J5 |
| 1 | LD1117S33TR | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | PJA3404_R1_00001 | Package_TO_SOT_SMD:TSOT-23_HandSoldering | U3 |
| 1 | RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | STM32G071RBT6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U2 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW2 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H9.5mm | SW1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J8 |
Similar boards
- 2 layers33 × 39 mm
- 2 layers120 × 96.5 mm
/ControlBoard/ControlBoard.kicad_pcb.jpg?size=s&soon)
- 4 layers
Pomodoro V1
MaxLell/Pomodoro_Clock
So this is basically what this device (will) is about. It will sit on my desk and ping me, when I need to take a break, and not only ping me, but rather shine a bright light at me, so that I actually get my lazy a up…
155 partsMIT - 2 layers40.3 × 39.7 mm
Power circuit new
Omkar1464/Telemetry-Module-using-CDMA-Modulation
This repository contains the embedded firmware, circuit schematics, simulation models, and validation benchmarks for the Long Range Telemetry Module (Phase-I) designed for high-altitude drone and UAV/CanSat payload…
32 parts - 4 layers86 × 145 mm
- 4 layers273 × 178 mm
Pico thing
markrvmurray/pico-thing
An 8-bit MC6809E / HD6309E single-board computer with a pair of Raspberry Pi Pico 2 (RP2350 / Pimoroni PGA2350) modules acting as intelligent bus peripherals, a 1–2 MB banked-RAM DAT/MMU, a 40-pin PATA hard-disk…
206 parts1BSD-2-Clause - 4 layers96 × 74 mm
Questions
How big is the Clovece nezlob se PCB PCB?
It measures 75 × 74 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Clovece nezlob se PCB use?
32 parts, built around the STM32G071RBT6, LD1117S33TR(MS), PJA3404_R1_00001 and DCJ200-10-A-K1-K. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Clovece nezlob se PCB KiCad files?
From the AdamZatloukal/DMP repository on GitHub, at the commit this page was made from: the board is Documentation/DPS/Clovece nezlob se PCB.kicad_pcb and its schematic Documentation/DPS/Clovece nezlob se PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Clovece nezlob se PCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask AdamZatloukal before reusing the design.