2 layers152.4 × 81.3 mm
LEDCube ESP32-C6 V1
97Cweb/Old-LEDCube
All the files from the LEDCube project, save for the library
42 parts
2 layers152.4 × 81.3 mm
LEDCube ESP32-C6 V2
97Cweb/Old-LEDCubeAll the files from the LEDCube project, save for the library
- Size
- 152.4 × 81.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 112
- Pads
- 342
- Tracks, vias
- 306, 102
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 9 Aug 2026
- Updated
- 9 Aug 2026
Overview
LEDCube ESP32-C6 V2 is an open-source printed circuit board by 97Cweb, from the 97Cweb/Old-LEDCube repository on GitHub. It is a 2-layer board of 152.4 × 81.3 mm with 59 parts on 112 nets, routed with 306 tracks and 102 vias.
It is built around the 74AHCT125D, TLC5948ADBQ and ESP32-C6-MINI-1, with the MIC5504-3.3YM5, IRF9530NPBF and WS2812B among its other parts. Its parts include 24 resistors, 11 capacitors, 9 connectors, 6 ICs and 4 transistors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
6
74AHCT125D
SOP-14-40℃~+125℃ 1 4 4.3ns@5V,50pF 4.5V~5.5V 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOP-14 Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffer/Driver/Transceiver
TLC5948ADBQ
SSOP-24-150mil-40℃~+85℃ 10V 16 2% 33MHz 3V~5.5V 60mA Built-in Over-Temperature Protection (OTP) PWM SSOP-24-150mil LED Drivers ROHSTexas InstrumentsLED Drivers
ESP32-C6-MINI-1
SMD,13.2x16.6mmSMD,13.2x16.6mm New Arrivals ROHSEspressif SystemsUncategorised
MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
IRF9530NPBF
TO-220AB-55℃~+175℃ 1 P-Channel 100V 14A 170pF 200mΩ@10V 4V 58nC@10V 760pF 79W P-Channel TO-220AB MOSFETs ROHSInfineon TechnologiesMOSFETs
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.md#LEDCube parts
the old LEDCube parts, minus the working library
This contains kicad board files, the early arduino codes, the box that the cube sits on, and some sample videos.
Next draft of cube will be with Beeton
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R8, R11, R15, R16, R17, R18, R19, R20, R21 |
| 7 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C1, C2, C6, C8, C9, C10, C12 |
| 5 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4, R5, R6, R7, R14 |
| 4 | IRF9530NPBF | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2, Q3, Q4 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_ISO14580 | H1, H2, H3, H4 |
| 3 | 10uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C5, C7, C11 |
| 3 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9, R10, R22 |
| 3 | 2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R25 |
| 3 | Conn_01x16_Female | Connector_JST:JST_XH_B16B-XH-A_1x16_P2.50mm_Vertical | J1, J2, J3 |
| 3 | TLC5948ADBQ | Package_DIP:DIP-24_W7.62mm | U1, U2, U3 |
| 2 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R12, R13 |
| 2 | 5k1 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R23, R24 |
| 2 | AudioJack3_SwitchTR | Connector_Audio:Jack_3.5mm_CUI_SJ1-3525N_Horizontal | J5, J6 |
| 2 | Conn_01x03_Female | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J7, J8 |
| 1 | 1uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C4 |
| 1 | 74AHCT125 | Package_DIP:DIP-14_W7.62mm | U4 |
| 1 | Conn_01x04_Female | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | ESP32-C6-MINI-1 | RF_Module:ESP32-C6-MINI-1 | U5 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J9 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D2 |
More from 97Cweb/Old-LEDCube
5- 2 layers72.4 × 151.1 mm
- 2 layers72.4 × 142.2 mm
- 2 layers63.5 × 137.2 mm
- 2 layers
Line In Daughter
97Cweb/Old-LEDCube
All the files from the LEDCube project, save for the library
5 parts
Similar boards
- 4 layers170.2 × 111.2 mm
E paper picture frame HW
JosefTAv/E-paper-picture-frame-HW
Hardware files for ESP32 based E-paper picture frame
110 partsMIT - 2 layers75.5 × 71 mm
- 2 layers58 × 81.7 mm
KICAD RECEPTEUR FINAL
badrbcb0405/Projet-1A-EMETTEUR-RECEPTEUR-IR
Embedded STM32 project based on two Nucleo-compatible shields: an IR remote shield and an IR receiver LED shield.
22 parts - 2 layers104.1 × 70 mm
- 4 layers90 × 77.9 mm
Lighting Tile Circuit V3
OA-Designs/LED-TILE
Modular decorative LED tiles in multiple shapes (hex, square, triangle...) sharing one PCB design. Tiles connect edge-to-edge to share power and sync lighting effects across a network.
77 partsGPL-3.0 - 2 layers372 × 45 mm
LED V1 18
Vipul0311/Smart-Rack
Factory floor SMT reel tracking system with ESP32 firmware, a custom sensor PCB, and a live-monitoring desktop app
26 parts - 2 layers81 × 55 mm
- 2 layers85 × 54 mm
Questions
How big is the LEDCube ESP32-C6 V2 PCB?
It measures 152.4 × 81.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LEDCube ESP32-C6 V2 use?
59 parts, built around the 74AHCT125D, TLC5948ADBQ, ESP32-C6-MINI-1 and MIC5504-3.3YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LEDCube ESP32-C6 V2 KiCad files?
From the 97Cweb/Old-LEDCube repository on GitHub, at the commit this page was made from: the board is KiCad/LEDCube ESP32-C6 V2/LEDCube ESP32-C6 V2.kicad_pcb and its schematic KiCad/LEDCube ESP32-C6 V1/LEDCube ESP32-C6 V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LEDCube ESP32-C6 V2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask 97Cweb before reusing the design.