
Europi main
AudioMorphology/Europi
Opensource sequencer software for Raspberry Pi equipped with Eurorack-compatible hardware

PCB to expand IO using I2C
IO BUTTON BOARD is an open-source printed circuit board by 74-Mathias, from the 74-Mathias/8_IO_BUTTON_BOARD repository on GitHub. It is a 2-layer board of 80 × 40 mm with 139 parts on 111 nets, routed with 1,290 tracks and 140 vias.
It is built around the PCF8574AP, 74HC86D and 74HC1G86GW. Its parts include 66 resistors, 17 transistors, 9 diodes, 8 connectors and 8 switches.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 49 | 1k | Resistors_SMD:R_0805 | R1, R3, R10, R14, R15, R19, R20, R21, R22, R23, R24, R25, R26, R27, R28, R29 +33 |
| 17 | 10k | Resistors_SMD:R_0805 | R2, R5, R11, R12, R13, R16, R17, R18, R43, R44, R45, R46, R47, R48, R49, R50 +1 |
| 12 | PNP | TO_SOT_Packages_SMD:SOT-23 | Q2, Q4, Q7, Q8, Q10, Q11, Q12, Q13, Q14, Q15, Q16, Q17 |
| 8 | SW_Push | Buttons_Switches_SMD:SW_SPST_EVQPE1 | SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17 |
| 5 | NPN | TO_SOT_Packages_SMD:SOT-23 | Q1, Q3, Q5, Q6, Q9 |
| 4 | MountingHole_4mm | Mounting_Holes:MountingHole_4mm | REF01, REF02, REF03, REF04 |
| 2 | 74HC86 | SMD_Packages:SOIC-14_N | U2, U3 |
| 2 | I2C | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | I2C, I2C |
| 1 | 100n | Capacitors_SMD:c_elec_4x4.5 | C1 |
| 1 | 74HC1G86GW | TO_SOT_Packages_SMD:SOT-353 | G1 |
| 1 | CONFIG | Housings_DIP:DIP-10_W7.62mm | CONF |
| 1 | D | Diodes_SMD:DO-214AB | D2 |
| 1 | IN_0 | LEDs:LED_0805 | IO_0 |
| 1 | IN_1 | LEDs:LED_0805 | IO_1 |
| 1 | IN_2 | LEDs:LED_0805 | IO_2 |
| 1 | IN_3 | LEDs:LED_0805 | IO_3 |
| 1 | IN_4 | LEDs:LED_0805 | IO_4 |
| 1 | IN_5 | LEDs:LED_0805 | IO_5 |
| 1 | IN_6 | LEDs:LED_0805 | IO_6 |
| 1 | IN_7 | LEDs:LED_0805 | IO_7 |
| 1 | IO_0 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P3 |
| 1 | IO_1 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P4 |
| 1 | IO_2 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P5 |
| 1 | IO_3 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P6 |
| 1 | IO_4 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P7 |
| 1 | IO_5 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P8 |
| 1 | IO_6 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P9 |
| 1 | IO_7 | Connectors_Molex:Molex_KK-6410-04_04x2.54mm_Straight | P10 |
| 1 | OUTPUT_MODE | LEDs:LED_0805 | OUTPUT_ON |
| 1 | OUT_0 | LEDs:LED_0805 | D13 |
| 1 | OUT_1 | LEDs:LED_0805 | D14 |
| 1 | OUT_2 | LEDs:LED_0805 | D15 |
| 1 | OUT_3 | LEDs:LED_0805 | D16 |
| 1 | OUT_4 | LEDs:LED_0805 | D17 |
| 1 | OUT_5 | LEDs:LED_0805 | D18 |
| 1 | OUT_6 | LEDs:LED_0805 | D19 |
| 1 | OUT_7 | LEDs:LED_0805 | D20 |
| 1 | PCF8574A | Housings_SOIC:SOIC-16W_7.5x10.3mm_Pitch1.27mm | U1 |
| 1 | POWER | LEDs:LED_0805 | POWER |
| 1 | REVERSE | LEDs:LED_0805 | REVERSE_ON |
| 1 | SW_0 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_0 |
| 1 | SW_1 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_1 |
| 1 | SW_2 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_2 |
| 1 | SW_3 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_3 |
| 1 | SW_4 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_4 |
| 1 | SW_5 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_5 |
| 1 | SW_6 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_6 |
| 1 | SW_7 | Pin_Header_1.27:PinSocket_1x03_P1.27mm_Vertical | IO_7 |

AudioMorphology/Europi
Opensource sequencer software for Raspberry Pi equipped with Eurorack-compatible hardware

AaronC81/delta-pico
Powerful scientific calculator based on the Raspberry Pi Pico



cutec-chris/PiScope
Goto Telescope with Raspberry PI HQ Camera and exchangable Objective Holders for DSLR Objectives

kellerkindt/bluepill_sensor
Bluepill stm31f103 ethernet sensor extension board with SW written in Rust

loscorpione/VFO-BFO-HF-ESP32-Si5351
VFO & BFO con Si 5351 gestito da ESP32 devkit V1 per la gamma di frequenze HF, da 1 a 30 MHZ

It measures 80 × 40 mm and has 2 copper layers, 1.6 mm thick.
139 parts, built around the PCF8574AP, 74HC86D and 74HC1G86GW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the 74-Mathias/8_IO_BUTTON_BOARD repository on GitHub, at the commit this page was made from: the board is IO_BUTTON_BOARD.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask 74-Mathias before reusing the design.