Skip to the content
2 layers78 × 57 mmStm32f103 min sys, the printed circuit board in 3D

Stm32f103 min sys

123Nert/ai_pcb

AI+Kicad

Size
78 × 57 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
44
Pads
138
Tracks, vias
561, 53
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
26 Sep 2026
Updated
26 Sep 2026

Overview

Stm32f103 min sys is an open-source printed circuit board by 123Nert, from the 123Nert/ai_pcb repository on GitHub. It is a 2-layer board of 78 × 57 mm with 31 parts on 44 nets, routed with 561 tracks and 53 vias.

It is built around the STM32F103C8T6 and AMS1117-3.3. Its parts include 14 capacitors, 7 connectors, 3 resistors, 2 ICs and 2 crystals. It belongs with the STM32 boards of this library.

Main components

2

README

README.md

STM32F103C8T6 最小系统板

使用 ZCode(GLM-5.3-Flash)+ KiCad 10 全流程 AI 辅助设计的可直接烧录的 STM32 最小系统板。

硬件特性

模块说明
主控STM32F103C8T6(LQFP-48,72MHz Cortex-M3,64KB Flash / 20KB RAM)
时钟HSE 8MHz 晶振(Y1 + 20pF×2)+ LSE 32.768kHz(Y2 + 12pF×2,支持 RTC)
复位10kΩ 上拉 + 100nF + 轻触按键(SW1),NRST 已引出
启动BOOT0 经 10kΩ 下拉(上电从 Flash 启动),BOOT1(PB2) 随排针引出
电源5V 输入 → AMS1117-3.3 LDO(输入/输出各 10µF)→ 3.3V,带电源指示灯
下载SWD 排针(3V3 / SWDIO / SWCLK / GND),PA9/PA10 串口亦在排针上
IO全部 GPIO 通过排针引出:PA0–PA15、PB0–PB15、PC13、NRST
去耦每个 VDD 引脚 100nF + 整体 10µF;VDDA 经磁珠独立滤波

排针引脚

排针引脚
J1(SWD)3V3 · SWDIO(PA13) · SWCLK(PA14) · GND
J2PA0 – PA7
J3PA8 – PA12 · PA15(SWDIO/SWCLK 已由 J1 引出)
J4PB0 – PB7
J5PB8 – PB15
J6PC13 · NRST
J75V 输入(接 USB 转 5V 或直流电源)

烧录方法

  1. 用 ST-Link 连接 J1:SWDIO → SWDIO,SWCLK → SWCLK,GND → GND,3V3 → 3V3
  2. BOOT0 已下拉,上电即从 Flash 启动,直接可在 STM32CubeProgrammer / Keil / OpenOCD 中下载调试
  3. 串口下载(可选):USB-TTL 接 PA9(TX) / PA10(RX),BOOT0 排针接 3V3 后复位进入系统bootloader

工程文件夹内容说明

核心工程文件(真正重要的 4 个)

文件说明
stm32f103_min_sys.kicad_pro工程文件——工程设置、DRC 约束规则都存在这里,双击它打开整个工程
stm32f103_min_sys.kicad_sch原理图——最小系统电路
stm32f103_min_sys.kicad_pcbPCB——布好线的板子(核心成果)
stm32f103_min_sys.pdf原理图导出的 PDF(给人看的版本)

设计过程产物(可重新生成)

文件说明
netlist.xml网表——原理图的连接关系清单,画 PCB 时的"施工依据"
board.dsn给 Freerouting 的自动布线任务文件(从 PCB 导出)
board.sesFreerouting 的布线结果(已导入回 PCB)
board_preview.png3D 渲染预览图
drc.rpt / erc.rptDRC/ERC 校验报告(当前:DRC 仅剩外观类提示,0 电气错误)

自动生成/系统文件(不用管)

文件说明
.git/git 仓库数据(版本历史就在这里,别动)
.gitignoregit 排除规则(备份/锁文件/缓存不入库)
.history/VS Code 本地历史插件缓存(已被 git 排除)
~stm32f103_min_sys.kicad_pro.lckKiCad 打开工程时的锁文件,正常关闭会自动消失
stm32f103_min_sys.kicad_prlKiCad 的本地界面状态(图层颜色、窗口位置等),自动生成

一句话总结:真正要备份的是 4 个核心文件(.pro/.sch/.pcb/.pdf),其余都能随时重新生成或删除。git 已经把核心文件都纳入版本管理了。

设计参数

  • 板框:78 × 57 mm,双层板(F.Cu 信号 / B.Cu 整面 GND 铺铜)
  • 线宽:信号 0.15–0.25 mm,电源 0.5 mm
  • 过孔:0.6/0.3 mm(外径/钻孔)
  • 最小线宽约束:0.1 mm(嘉立创等板厂均可制造)

复现方式

本工程由 ZCode 智能体驱动 KiCad 10 完成:

  1. 原理图:通过 MCP 工具(kicad-sch-api)放置器件、连线、标注网络
  2. 封装:全部器件指定 KiCad 标准封装(0603 阻容 / LQFP-48 / SOT-223 / 2.54mm 排针)
  3. PCB:脚本创建板框与布局,按网表分配焊盘网络
  4. 布线:导出 Specctra DSN → Freerouting 自动布线(94 网络全通)→ 导入 SES
  5. 验证:ERC / DRC 全部通过(剩余仅丝印外观类提示)

许可

仅供学习交流使用。

Parts

31
QtyValueFootprintReferences
6100nFC_0603_1608MetricC3, C4, C5, C6, C8, C10
310uFC_0603_1608MetricC7, C13, C14
210kR_0603_1608MetricR1, R2
212pFC_0603_1608MetricC11, C12
220pFC_0603_1608MetricC1, C2
11kR_0603_1608MetricR3
11uFC_0603_1608MetricC9
132.768kHzCrystal_SMD_3215-2Pin_3.2x1.5mmY2
15V_INPinHeader_1x02_P2.54mm_VerticalJ7
1600R@100MHzL_0603_1608MetricFB1
18MHzCrystal_SMD_HC49-SDY1
1AMS1117-3.3SOT-223-3_TabPin2U2
1PA0-PA7PinHeader_1x08_P2.54mm_VerticalJ2
1PA8-PA15PinHeader_1x08_P2.54mm_VerticalJ3
1PB0-PB7PinHeader_1x08_P2.54mm_VerticalJ4
1PB8-PB15PinHeader_1x08_P2.54mm_VerticalJ5
1PC13/NRSTPinHeader_1x02_P2.54mm_VerticalJ6
1PWRLED_0603_1608MetricLED1
1RESETSW_PUSH_6mmSW1
1STM32F103C8T6LQFP-48_7x7mm_P0.5mmU1
1SWDPinHeader_1x04_P2.54mm_VerticalJ1

Similar boards

  • 2 layers68 × 40 mmStm32-io extend, the printed circuit board in 3D

    Stm32-io extend

    hardenedlinux/cheap-pcb

    Cheap PCB: Better understanding the current status of hardware supply chain

    44 parts170CC0-1.0
  • 2 layers99.1 × 58.4 mmHEAT, the printed circuit board in 3D

    HEAT

    milar111/HEAT

    An open-source STM32 SMD assembly station for precision soldering. Uses a custom Smart Pulse & Coast algorithm to drive 400W mains heaters via SSR. Features OLED UI, NTC feedback, and safety cooling.

    57 parts9
  • 2 layers71.3 × 25.4 mmUSB DALI, the printed circuit board in 3D

    USB DALI

    even-notodd/USB-DALI

    USB-DALI interface converter

    43 parts4
  • 2 layers78 × 60 mmDC Motor Controller, the printed circuit board in 3D

    DC Motor Controller

    minhle4397/Line-Follower-Robot-v2

    Improved Hardware and Firmware for Line Follower Robot

    53 parts3
  • 4 layers36 × 36 mmTrackMAG, the printed circuit board in 3D

    TrackMAG

    mupfdev/TrackMAG

    An open hardware development board primarily intended for the development of accessible input devices.

    58 parts3
  • 2 layers154.7 × 113 mmDeskMixer, the printed circuit board in 3D

    DeskMixer

    RaduAndre/DeskMixer

    DeskMixer is a software that allows control of application volumes with real sliders, and action mapping on buttons using arduino like platforms. The project was inspired originally by deej.

    113 parts3
  • 2 layers42 × 33 mmSTM32 course, the printed circuit board in 3D

    STM32 course

    abda-s/STM32-Phill-s-Lab-PCB-Course

    A beginner-friendly introduction to STM32 hardware design and KiCad

    32 parts2
  • 2 layers53.3 × 35.6 mmStm32 minimal dev, the printed circuit board in 3D

    Stm32 minimal dev

    amrithHN/stm32_minimal_dev

    stm32 based minimal dev board

    33 parts2GPL-3.0

Questions

How big is the Stm32f103 min sys PCB?

It measures 78 × 57 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Stm32f103 min sys use?

31 parts, built around the STM32F103C8T6 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Stm32f103 min sys KiCad files?

From the 123Nert/ai_pcb repository on GitHub, at the commit this page was made from: the board is stm32f103_min_sys.kicad_pcb and its schematic stm32f103_min_sys.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Stm32f103 min sys design in my own project?

Its repository states no licence, so its author keeps all rights: ask 123Nert before reusing the design.