Skip to the content
2 layers94 × 53.5 mmController, the printed circuit board in 3D

A shoddy 3-phase controller for Varian V-200 turbomolecular pumps.

Size
94 × 53.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
50
Nets
49
Pads
153
Tracks, vias
431, 40
Pours
7
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
15 Jan 2019
Updated
27 Jul 2021

Overview

Controller is an open-source printed circuit board by 0xDBFB7, from the 0xDBFB7/varian-turbo-controller repository on GitHub, published under the MIT licence. It is a 2-layer board of 94 × 53.5 mm with 50 parts on 49 nets, routed with 431 tracks and 40 vias.

Its parts include 23 resistors, 14 capacitors, 6 transistors, 3 ICs and 3 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

README

README.md

This is a small, simple half-bridge circuit that commutates 54 volts into 3-phase at 850 Hz, peak power of about 1 kw for a few minutes, for use with the Varian Turbo-V series of turbomolecular pumps.

WARNING: This board has only been tested for a few hours. The software does not provide any of the sensing or safety features present in the stock controller. It might blow up your pump, kill your cat, spin the earth around your impeller, etc.

Not that I'm a paragon of best practice in any case, but this seriously isn't an acceptable level of quality. In particular, it was designed to be etched at home, as my normal board house was closed for the holidays. I've had one instance where shoot-through blew up one of the MOSFETs. I don't know what would happen if this occurs while the pump is at maximum speed. Adding fuseholders between the legs of the half-bridge - and perhaps between each phase to the pump - would probably be a good idea to prevent catastrophic braking.

There are several other open-source turbomolecular pump controller projects online that are better developed and that might be preferable. In addition, the pumps use a kind of synchronous or induction motor, not a "brushless"-like, so no sensing is needed, only a constant 850 Hz, which is basically just a 3-phase VFD or motor controller. Unfortunately, I wasn't able to find any off-the-shelf system with the required parameters.

The circuit is simple enough to easily be built on perfboard. Schematic and bill of materials are here. The power MOSFETs are BUK9620, with MIC4604YM-TR half-bridge charge-pump drivers.

The input power was supplied by a MeanWell SE-1000-48 with the voltage trimpot adjusted to ~56V, through a DROK Model 200310 10-75V to 0-60V switching buck converter (Amazon), current limit set to about 8A.

I highly recommend using such a constant-current regulator, because the power supply is extremely powerful - it's practically an arc flash hazard and will easily start a fire.

The MeanWell supply is probably overkill (very expensive), but a cheaper Amazon 48V supply exploded and I didn't want to tempt fate.

I don't know what terminations the turbopump connector uses; crimp butt connectors worked brilliantly.

Original Varian controller manual

Pump manual

Things that should be added:

If the back-emf sensing is commutated improperly, -5v or so will be put into the sense ADC pins. The integral protection diodes might be okay with that, but probably not. This is disabled at the moment.

More filtering and decoupling should be added. This pump draws nearly 700 watts on startup - there are some massive transients on the power supply rail.

Parts

50
QtyValueFootprintReferences
101k*0603R2, R4, R6, R7, R8, R12, R13, R17, R18, R23
910uf-1210-25v*1210C5, C7, C8, C9, C11, C12, C13, C15, C16
62.2r*0805R9, R10, R14, R15, R19, R20
6MOSFET-NCH-PSMN7R0TO-263_D2PAKQ1, Q2, Q3, Q4, Q5, Q6
424k0603R1, R3, R5, R22
30.005r1206R11, R16, R21
30.1uf*0603C6, C10, C14
3MIC4604*Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU1, U2, U3
2CPCapacitor_THT:CP_Radial_D16.0mm_P7.50mmC1, C2
112vSCREWTERMINAL-5MM-2J2
148vSCREWTERMINAL-5MM-2J3
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1CONN_03-SCREW-5MMSCREWTERMINAL-5MM-3J1

Similar boards

  • 2 layers187.2 × 26.6 mmBlade12, the printed circuit board in 3D

    Blade12

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    50 parts3.7k
  • 2 layers45.7 × 25.9 mmAccessory, the printed circuit board in 3D

    Accessory

    usbarmory/usbarmory

    USB armory - The open source compact secure computer

    50 parts1.5k
  • 2 layers21 × 31.5 mmK1-aioc, the printed circuit board in 3D

    K1-aioc

    skuep/AIOC

    Ham Radio All-in-one-Cable

    50 parts1.4kMIT
  • 2 layers42 × 32.5 mmLipoboard, the printed circuit board in 3D

    Lipoboard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    50 parts915
  • 2 layers101 × 31.5 mmManagement, the printed circuit board in 3D

    Management

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    50 parts397Apache-2.0
  • 2 layers123.9 × 94.4 mmRoba R, the printed circuit board in 3D

    Roba R

    kumamuk-git/roBa

    50 parts363GPL-3.0
  • 2 layers50 × 25 mmMbus master, the printed circuit board in 3D

    Mbus master

    roarfred/AmsToMqttBridge

    Minimalistic system to read AMS/HAN data from electrical meter

    50 parts223

Questions

How big is the Controller PCB?

It measures 94 × 53.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Controller use?

50 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Controller KiCad files?

From the 0xDBFB7/varian-turbo-controller repository on GitHub, at the commit this page was made from: the board is files/controller/controller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Controller design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).