Skip to the content
12345678

XTSD08GLGEAG

XTXExtended

-30℃~+85℃ 2.7V~3.6V 20mA 50MHz 8Gbit SPI、SD interface LGA-8(6x8) NAND FLASH ROHS

Part id
xtx/XTSD08GLGEAG
Category
NAND FLASH
Package
LGA-8(6x8)
Pins
8
In stock
0 at JLCPCB (C558840)
Used on
3 open-source boards

Overview

The XTSD08GLGEAG is a NAND FLASH made by XTX in a LGA-8(6x8) package with 8 pins. -30℃~+85℃ 2.7V~3.6V 20mA 50MHz 8Gbit SPI、SD interface LGA-8(6x8) NAND FLASH ROHS.

PCBKit's library has its KiCad symbol (Memory_Flash:XTSD08G, from KiCad's library) and its footprint (Package_LGA:LGA-8_8x6mm_P1.27mm, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C558840). 3 open-source boards in 2 repositories on GitHub use it.

Symbol

1SD22SD3/CS3CLK4VSS5CMD/DI6SD0/DO7SD18VDD
Memory_Flash:XTSD08GFrom KiCad's library

Footprint

12345678
Package_LGA:LGA-8_8x6mm_P1.27mmFrom KiCad's library

From the datasheet

8
Supply, least
2.7 V · VDD, recommended operating min · p. 5
Supply, most
3.6 V · VDD, recommended operating max · p. 5
Works from
-30 °C · Ta, operating ambient min · p. 3
Works up to
85 °C · Ta, operating ambient max · p. 3
Takes working
30 mA · Read current max, 3.6 V, 25 MHz or 50 MHz · p. 5
Takes at most
30 mA · Write current max, 3.6 V, 25 MHz or 50 MHz · p. 5
Takes asleep
200 µA · Standby current max, VDD = 3.0 V, clock stopped, Ta = 25°C · p. 5
Takes asleep
20 mA · Standby current max, VDD = 3.6 V, clock 25 MHz; based on 100 samples · p. 5

What it is and has

7
Flash memory
8Gbit (1GByte) · p. 8
Interface
SD2.0 · p. 8
Clock frequency
Up to 50Mhz · p. 3
Bus width
1/4 bit mode · p. 3
NAND management
Built-in HW ECC Engine and highly reliable NAND management mechanism · p. 3
Write speed
Up to class 8 · p. 3
Package
LGA8 (Land Grid Array), 8x6mm · p. 3

Specifications

16
ParameterConditionsAs printedPage
Temperature Range TaOperation Conditionsmin -30 · max 85 degrees centigrade3
Temperature Range TstgStorage Conditionsmin -40 · max 85 degrees centigrade3
Supply voltage VDDmin 2.7 · max 3.6 V5
Standby Current(*) Icc1VDD=3.6V, clock 25MHz; maximum based on 100 pcs samplesmax 20 mA5
Standby Current(*) Icc1VDD=3.0V, clock STOP, Ta=25°Cmax 0.2 mA5
Operation Current(*) Write I3.6V/25MHz,50MHzmax 30 mA5
Operation Current(*) Read I3.6V/25MHz,50MHzmax 30 mA5
Input voltage setup Time Vrsmax 250 ms5
Peak voltage on all linesmin -0.3 V5
Input Leakage Current for all pinsmin -10 · max 10 uA5
Output Leakage Current for all outputsmin -10 · max 10 uA5
Pull up Resistance RCMD/RDATmin 10 · max 100 k5
Total bus capacitance for each signal line CL1 card; CHOST+CBUS≤30pFmax 40 pF5
Card Capacitance for signal pin CCARDmax 10 pF5
Pull up Resistance inside card (pin1) RDAT3min 10 · max 90 k5
Capacity Connected to Power line CCmax 5 pF5

Pins, by the datasheet

8
1 SD2
I/O pin in SD mode; no connection in SPI mode. · p. 4
2 SD3
I/O pin in SD mode; /CS chip select in SPI mode. · p. 4
3 CLK
Clock signal in SD and SPI modes. · p. 4
4 Vss
Ground. · p. 4
5 CMD
Command signal in SD mode; DI data input in SPI mode. · p. 4
6 SD0
I/O pin in SD mode; DO data output in SPI mode. · p. 4
7 SD1
I/O pin in SD mode; no connection in SPI mode. · p. 4
8 Vdd
Power supply. · p. 4

Ordering codes, by the datasheet

1
XTSD08GLGEAG
LGA8 (Land Grid Array) · 8Gbit (1GByte), 8x6mm, extended temperature -30°C to +85°C, tray packing, Green/Reach package · p. 3

Open-source boards using it

3
  • 2 layers20 × 20 mmChest, the printed circuit board in 3D

    Chest

    icl-rocketry/Ricardo-Chest

    Chest

    10 partsMIT
  • 4 layers49.8 × 46.6 mmRicardo BlackBoxNEW, the printed circuit board in 3D

    Ricardo BlackBoxNEW

    icl-rocketry/Ricardo-JollyRoger

    Flight Data Recorder (FDR) for ICLR flight vehicles

    87 parts
  • 4 layers62 × 32 mmRicardo BlackBoxNEWFinal, the printed circuit board in 3D

    Ricardo BlackBoxNEWFinal

    icl-rocketry/Ricardo-JollyRoger

    Flight Data Recorder (FDR) for ICLR flight vehicles

    82 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the XTSD08GLGEAG?

Yes. The symbol is Memory_Flash:XTSD08G and the footprint Package_LGA:LGA-8_8x6mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the XTSD08GLGEAG?

LGA-8(6x8), with 8 pins. Its footprint is drawn on this page.

Where is the XTSD08GLGEAG datasheet?

XTX publishes it: the Datasheet link on this page opens it.

Where can I order the XTSD08GLGEAG?

JLCPCB lists it as part C558840, with 0 in stock; the sellers' links on this page open their listings.

What can replace the XTSD08GLGEAG?

Parts like it in the library: the XTSD01GLGEAG by XTX, the XTSD04GLGEAG by XTX, the XTSD04GCLGEGA by XTX and the XTSD02GLGEAG by XTX. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the XTSD08GLGEAG?

3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.