Skip to the content
12345678

UCC27524D

Texas InstrumentsExtended

-40℃~+140℃ 1.9V~2.3V 1V~1.4V 2 4.5V~18V 5A 5A 7ns 9ns Low Side MOSFET Under Voltage Protection SOIC-8 Gate Drivers ROHS

Part id
ti/UCC27524D
Category
Gate Drivers
Package
SOIC-8
Pins
8
In stock
17,287 at JLCPCB (C465729)
Used on
2 open-source boards

Overview

The UCC27524D is a gate Driver made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+140℃ 1.9V~2.3V 1V~1.4V 2 4.5V~18V 5A 5A 7ns 9ns Low Side MOSFET Under Voltage Protection SOIC-8 Gate Drivers ROHS.

PCBKit's library has its KiCad symbol (Driver_FET:UCC27524D, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 17,287 are in stock at JLCPCB (part C465729). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1ENA2INA3GND4INB5OUTB6VDD7OUTA8ENB
Driver_FET:UCC27524DFrom KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

13
Supply, least
4.5 V · VDD, recommended operating min · p. 5
Supply, most
18 V · VDD, recommended operating max · p. 5
Supply, absolute maximum
20 V · VDD, absolute max · p. 5
Junction, hottest
150 °C · Virtual junction temperature, absolute max · p. 5
Takes working
3.2 mA · VDD operating current, typical, 1000 kHz PWM, outputs unloaded · p. 6
Takes at most
3.8 mA · VDD operating current, max, 1000 kHz PWM, outputs unloaded · p. 6
Takes asleep
800 µA · VDD disable current, typical, VINx = 3.3 V, ENx = 0 V · p. 6
Gives
300 mA · Continuous source/sink current per output, absolute max · p. 5
A pin gives at most
300 mA · OUTA or OUTB continuous source/sink current, absolute max · p. 5
Junction to air (D)
126.4 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to board (D)
69.9 K/W · Junction-to-board thermal resistance · p. 6
Junction to case (D)
67 K/W · Junction-to-case top thermal resistance · p. 6
Edge
6 ns · Rise time, typical, CLOAD = 1.8 nF, 20% to 80% · p. 8

What it is and has

11
Gate-drive channels
Two independent channels · p. 1
Peak drive current
5 A source and sink · p. 1
Enable
Independent enable for each output · p. 1
Input negative voltage capability
–5 V · p. 1
Propagation delay
17 ns typical · p. 1
Rise and fall times
6 ns and 10 ns typical · p. 1
Channel delay matching
1 ns typical · p. 1
Floating input behavior
Outputs held low · p. 1
Protection
VDD undervoltage lockout holds outputs low · p. 14
Logic compatibility
CMOS/TTL compatible input and enable thresholds with wide hysteresis · p. 14
Package
D, SOIC 8, 4.90 mm × 3.91 mm body · p. 1

Specifications

47
ParameterConditionsAs printedPage
Supply voltage VDDOver operating free-air temperature range; relative to GNDmin -0.3 · max 20 V5
OUTA, OUTB voltageDC; maximum VDD + 0.3 Vmin -0.3 V5
OUTA, OUTB voltageRepetitive pulse < 200 ns; maximum VDD + 0.3 Vmin -2 V5
Output continuous source/sink current IOUT_DCmax 0.3 A5
Output pulsed source/sink current (0.5 us) IOUT_pulsed0.5 us pulsemax 5 A5
INA, INB, ENA, ENB voltage(3)D packagemin -5 · max 20 V5
Operating virtual junction temperature, TJ TJmin -40 · max 150 °C5
Storage temperature, Tstg Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)D package; Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 Vmax 1000 V5
Supply voltage, VDD VDD12 V nominalmin 4.5 · typ 12 · max 18 V5
Operating junction temperaturemin -40 · max 140 °C5
Input voltage, INA, INBD packagemin -2 · max 18 V5
Enable voltage, ENA and ENBmin -2 · max 18 V5
Junction-to-ambient thermal resistance RθJAD, 8 PINStyp 126.4 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)D, 8 PINStyp 67 °C/W6
Junction-to-board thermal resistance RθJBD, 8 PINStyp 69.9 °C/W6
Junction-to-top characterization parameter ψJTD, 8 PINStyp 19.2 °C/W6
Junction-to-board characterization parameter ψJBD, 8 PINStyp 69.1 °C/W6
VDD quiescent supply current IVDDqD package; VINx = 3.3 V, VDD = 3.4 V, ENx = VDDtyp 300 · max 450 uA6
VDD static supply current IVDDD package; VINx = 3.3 V, ENx = VDD; VDD = 12 V; no output loadtyp 0.6 · max 1 mA6
VDD static supply current IVDDD package; VINx = 0 V, ENx = VDD; VDD = 12 V; no output loadtyp 0.7 · max 1 mA6
VDD operating current IVDDOD package; fSW = 1000 kHz, ENx = VDD, VINx = 0 V – 3.3 V PWM; VDD = 12 V; no output loadtyp 3.2 · max 3.8 mA6
VDD disable current IDISD package; VINx = 3.3 V, ENx = 0 V; VDD = 12 V; no output loadtyp 0.8 · max 1.1 mA6
VDD UVLO rising threshold VVDD_OND packagemin 3.8 · typ 4.1 · max 4.4 V6
VDD UVLO falling threshold VVDD_OFFD packagemin 3.5 · typ 3.8 · max 4.1 V6
VDD UVLO hysteresis VVDD_HYSD packagetyp 0.3 V6
Input signal high threshold VINx_HD package; Output High, ENx = HIGHmin 1.8 · typ 2 · max 2.3 V6
Input signal low threshold VINx_LD package; Output Low, ENx = HIGHmin 0.8 · typ 1 · max 1.2 V6
Input signal hysteresis VINx_HYSD packagetyp 1 V6
INx pin pulldown resistor RINxD package; INx = 3.3 Vtyp 120 kΩ6
Enable signal high threshold VENx_HD package; Output High, INx = HIGHmin 1.8 · typ 2 · max 2.3 V7
Enable signal low threshold VENx_LD package; Output Low, INx = HIGHmin 0.8 · typ 1 · max 1.2 V7
Enable signal hysteresis VENx_HYSD packagetyp 1 V7
EN pin pullup resistance RENxD package; ENx = 0 Vtyp 200 kΩ7
Peak output source current ISRCD package; VDD = 12 V, CVDD = 10 uF, CL = 0.1 uF, f = 1 kHztyp 5 A7
Peak output sink current ISNKD package; VDD = 12 V, CVDD = 10 uF, CL = 0.1 uF, f = 1 kHztyp -5 A7
Pullup resistance ROHD package; IOUT = –50 mA, See Section 7.3.4.; DC measurement of PMOS structure onlytyp 5 · max 8.5 Ω7
Pulldown resistance ROLD package; IOUT = 50 mAtyp 0.6 · max 1.1 Ω7
Rise time tRxD package; CLOAD = 1.8 nF, 20% to 80%, Vin = 0 V – 3.3 V; VDD = VEN = 12 Vtyp 6 · max 10 ns8
Fall time tFxD package; CLOAD = 1.8 nF, 90% to 10%, Vin = 0 V – 3.3 V; VDD = VEN = 12 Vtyp 10 · max 14 ns8
Turn-on propagation delay tD1xD package; CLOAD = 1.8 nF, VINx_H of the input rise to 10% of output rise, Vin = 0 V – 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°Ctyp 17 · max 27 ns8
Turn-off propagation delay tD2xD package; CLOAD = 1.8 nF, VINx_L of the input fall to 90% of output fall, Vin = 0 V – 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°Ctyp 17 · max 27 ns8
Enable propagation delay tD3xD package; CLOAD = 1.8 nF, VENx_H of the enable rise to 10% of output rise, Vin = 0 V – 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°Ctyp 17 · max 27 ns8
Disable propagation delay tD4xD package; CLOAD = 1.8 nF, VENx_L of the enable fall to 90% of output fall, Vin = 0 V – 3.3 V, Fsw = 500 kHz, 50% duty cycle, TJ = 125°Ctyp 17 · max 27 ns8
Delay matching between two channels tMD package; CLOAD = 1.8 nF, Vin = 0 V – 3.3 V, Fsw = 500 kHz, 50% duty cycle, INA = INB, |tRA – tRB|, |tFA – tFB|typ 1 · max 2 ns8
Minimum input pulse width tPWminD package; CL = 1.8 nF, Vin = 0 V – 3.3 V, Fsw = 500 kHz, Vo > 1.5 Vtyp 10 · max 15 ns8

Pins, by the datasheet

8
1 ENA
Channel A enable; LOW disables OUTA regardless of INA, HIGH or floating enables it. · p. 4
2 INA
Channel A non-inverting input; OUTA is held LOW if unbiased or floating. · p. 4
3 GND
Ground; all signals are referenced to this pin. · p. 4
4 INB
Channel B non-inverting input; OUTB is held LOW if unbiased or floating. · p. 4
5 OUTB
Output of Channel B. · p. 4
6 VDD
Bias supply input. · p. 4
7 OUTA
Output of Channel A. · p. 4
8 ENB
Channel B enable; LOW disables OUTB regardless of INB, HIGH or floating enables it. · p. 4

Open-source boards using it

2
  • 6 layers100 × 175 mmV1sch, the printed circuit board in 3D

    V1sch

    spartacus-hf/spartacus_PCB_REV1

    KiCad schematic and PCB project for the SPARTACUS-HF Chireix transceiver.

    438 parts1CERN-OHL-S-2.0
  • 6 layers141.7 × 105.1 mmNuBoard, the printed circuit board in 3D

    NuBoard

    wickerwaka/nuBoard

    Verified 2026-09-24 with KiCad 10.0.6. Open nuBoard.kicadpcb in this directory to inspect the result. This is a PCB-only candidate, separate from the main-board schematic and PCB.

    330 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the UCC27524D?

Yes. The symbol is Driver_FET:UCC27524D and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the UCC27524D?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the UCC27524D datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the UCC27524D?

JLCPCB lists it as part C465729, with 17,287 in stock; the sellers' links on this page open their listings.

What can replace the UCC27524D?

Parts like it in the library: the MP6610GS-Z by Monolithic Power Systems, the EG2131 by EG, the SLM2186CA-DG by Sillumin and the IR2104STRPBF by Infineon Technologies. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the UCC27524D?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.