Skip to the content

TUSB321AIRWBR

Texas InstrumentsExtended

-40℃~+85℃ 4.5V~5.5V 70uA USB Type-C X2-QFN-12(1.6x1.6) Interface - Specialized ROHS

Part id
ti/TUSB321AIRWBR
Category
Interface, Specialized
Package
X2-QFN-12(1.6x1.6)
Pins
12
In stock
3,692 at JLCPCB (C2674046)
Used on
1 open-source board

Overview

The TUSB321AIRWBR is an interface, Specialized made by Texas Instruments in a X2-QFN-12(1.6x1.6) package with 12 pins. -40℃~+85℃ 4.5V~5.5V 70uA USB Type-C X2-QFN-12(1.6x1.6) Interface - Specialized ROHS.

PCBKit's library has its KiCad symbol (Interface_USB:TUSB321, from KiCad's library) and its footprint (Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mm, from KiCad's library), ready for a KiCad board. 3,692 are in stock at JLCPCB (part C2674046). 1 open-source board in 1 repository on GitHub use it.

Symbol

1CC12CC23CURRENT_MODE4PORT5VBUS_DET6VCONN_FAULT7OUT18OUT29ID10GND11DIR12VDD
Interface_USB:TUSB321From KiCad's library

Footprint

Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mmFrom KiCad's library

From the datasheet

10
Supply, least
4.5 V · VDD, recommended operating min · p. 4
Supply, most
5.5 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
6 V · VDD, absolute maximum · p. 4
Works from
-40 °C · Operating free air temperature min · p. 4
Works up to
85 °C · Operating free air temperature max · p. 4
Takes working
70 µA · VDD, active UFP mode typical, VDD = 5 V, PORT = L · p. 5
Current limit
300 mA · VCONN current limit typical · p. 6
Junction to air (RWB (X2QFN))
169.3 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (RWB (X2QFN))
68.1 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (RWB (X2QFN))
83.4 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

5
USB Type-C specification
1.1 · p. 1
Port modes
DFP, UFP, DRP · p. 1
VBUS detection
Supported · p. 1
VCONN
Support for active cables · p. 1
Package
X2QFN (12), 1.60 mm × 1.60 mm · p. 1

Around it

8
res 200 kΩ
between VCONN_FAULT and pullup supply; External pullup for open-drain output. · p. 6
res 4.7 kΩ
between PORT and VDD; Tri-level input external pullup for DFP mode. · p. 6
res 500-kΩ
between CURRENT_MODE and VDD; Advertise medium current at 1.5 A. · p. 9
res 10-kΩ
between CURRENT_MODE and VDD; Advertise 3 A in the design example. · p. 13
res 900-kΩ
between VBUS_DET and VBUS; Required to protect the detection input from large VBUS voltage. · p. 13
cap 100-nF
between VDD and GND; Place near VDD. · p. 13
cap 100 µF
between VDD and GND; Bulk capacitance in the design example. · p. 13
cap 150-µF
between VBUS and GND; DFP design example; at least 120 uF is required. · p. 13

Specifications

58
ParameterConditionsAs printedPage
Supply voltage VDDOver operating free-air temperature rangemin -0.3 · max 6 V4
Control pinsCC1, CC2, PORT, CURRENT_MODE, ID, DIR, VCONN_FAULT; maximum VDD + 0.3 Vmin -0.3 V4
Control pinsOUT1, OUT2; maximum VDD + 0.3 Vmin -0.3 V4
Control pins VBUS_DETmin -0.3 · max 4 V4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±3000 Vmax 3000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1500 Vmax 1500 V4
Supply voltage range,VDD VDDmin 4.5 · max 5.5 V4
System VBUS voltageNominal 5 Vmin 4 · typ 5 · max 28 V4
DC Voltage range for VBUS_DET VBUS_DETmin 0 · max 4 V4
DC Voltage range for control pinsID, DIR, VCONN_FAULT, OUT1, OUT2, CURRENT_MODE, CC1, CC2, PORTmin 0 · max 5.5 V4
Supply for active cable (With VDD at 5 V) VCONNVDD at 5 Vmin 4.75 · max 5.5 V4
Operating free air temperature TANominal 25 °Cmin -40 · typ 25 · max 85 °C4
Junction-to-ambient thermal resistance RθJARWB (X2QFN), 12 PINStyp 169.3 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)RWB (X2QFN), 12 PINStyp 68.1 °C/W4
Junction-to-board thermal resistance RθJBRWB (X2QFN), 12 PINStyp 83.4 °C/W4
Junction-to-top characterization parameter ψJTRWB (X2QFN), 12 PINStyp 2.2 °C/W4
Junction-to-board characterization parameter ψJBRWB (X2QFN), 12 PINStyp 83.4 °C/W4
Current consumption in unattached mode when port is unconnected and waiting for connection. I(UNATTACHED_UFP)VDD = 5 V, PORT = Ltyp 70 uA5
Current consumption in active mode. I(ACTIVE_UFP)VDD = 5 V, PORT = Ltyp 70 uA5
Pulldown resistor when in UFP or DRP mode. R(CC_D)min 4.6 · typ 5.1 · max 5.6 kΩ5
Pulldown resistor when in dead-battery mode RCC_DBVDD = 0V.min 4.1 · typ 5.1 · max 6.1 kΩ5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising default current source capability. VUFP_CC_USBmin 0.25 · max 0.61 V5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising medium (1.5 A) current source capability. VUFP_CC_MEDmin 0.7 · max 1.16 V5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising high (3 A) current source capability. VUFP_CC_HIGHmin 1.31 · max 2.04 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising default current source capability. VTH(DFP_CC_USB)min 1.51 · typ 1.6 · max 1.64 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising medium current (1.5 A) source capability. VTH(DFP_CC_MED)min 1.51 · typ 1.6 · max 1.64 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising high current (3.0 A) source capability. VTH(DFP_CC_HIGH)min 2.46 · typ 2.6 · max 2.74 V5
Voltage threshold for detecting a active cable attach when configured as a DFP and advertising default current source. VTH(AC_CC_USB)min 0.15 · typ 0.2 · max 0.25 V5
Voltage threshold for detecting a active cable attach when configured as a DFP and advertising medium current (1.5 A) source. VTH(AC_CC_MED)min 0.35 · typ 0.4 · max 0.45 V5
Voltage threshold for detecting a active cable attach when configured as a DFP and advertising high current (3 A) source. VTH(AC_CC_HIGH)min 0.76 · typ 0.8 · max 0.84 V5
Default mode pullup current source when operating in DFP or DRP mode. ICC(DEFAULT_P)min 64 · typ 80 · max 96 uA5
Medium (1.5 A) mode pullup current source when operating in DFP or DRP mode. ICC(MED_P)min 166 · typ 180 · max 194 uA5
High (3 A) mode pullup current source when operating in DFP or DRP mode. ICC(HIGH_P)VDD must be 3.5 V or greater to advertise 3 A current.min 304 · typ 330 · max 356 uA5
Low-level control signal input voltage, (PORT, CURRENT_MODE) VILmax 0.4 V5
High-level input current IIHmin -20 · max 20 uA5
Low-level input current IILmin -10 · max 10 uA5
Current leakage for ID pin. IID_LEAKAGEVDD = 0V; ID = 5Vmax 10 uA5
Internal pullup resistance (PORT) RPUtyp 588 kΩ5
Internal pulldown resistance (PORT) RPDtyp 1.1 MΩ5
Internal pulldown resistance for CURRENT_MODE pin RPD(CUR)typ 275 kΩ5
Low-level signal output voltage (open-drain) (VCONN_FAULT, ID, OUT1, OUT2, DIR) VOLIOL = –1.6 mAmax 0.4 V5
External pullup resistor on open drain IOs (VCONN_FAULT, ID, OUT1, OUT2, DIR) RP(ODext)typ 200 kΩ6
Tri-level input external pull-up resistor (PORT) RP(TLext)typ 4.7 kΩ6
External pull-up resistor on CURRENT_MODE pin to advertise 1.5-A current RP(cm_med)typ 500 kΩ6
External pull-up resistor on CURRENT_MODE pin to advertise 3.0-A current RP(cm_high)typ 10 kΩ6
VBUS threshold range VBUS(THR)VBUS_DET connected to System VBUS signal through external resistormin 2.95 · typ 3.3 · max 3.8 V6
External resistor between VBUS and VBUS_DET pin RVBUSmin 855 · typ 887 · max 920 KΩ6
Internal pulldown resistance for VBUS_DET R(VBUS_PD)typ 95 KΩ6
On resistance of the VCONN power FET RONmax 1.25 Ω6
Voltage tolerance on VCONN power FET V(TOL)max 5.5 V6
Voltage to pass through VCONN power FET V(PASS)max 5.5 V6
VCONN current limit; VCONN is disconnected above this value I(VCONN)min 225 · typ 300 · max 375 mA6
Bulk capacitance on VCONN; placed on VDD supply CBULKmin 10 · max 200 uF6
Power on default of CC1 and CC2 voltage debounce time tCCCB_DEFAULTtyp 168 ms6
Debounce of VBUS_DET pin after valid V(BUS_THR) (See Figure 1.) tVBUS_DBtyp 2 ms6
Power-on default of percentage of time DRP advertises DFP during a TDRP tDRP_DUTY_CYCLEtyp 30 %6
The period TUSB321AI in DRP mode completes a DFP to UFP and back advertisement. tDRPmin 50 · typ 75 · max 100 ms6

Pins, by the datasheet

12
1 CC1
Type-C configuration channel signal 1. · p. 3
2 CC2
Type-C configuration channel signal 2. · p. 3
3 CURRENT_MODE
Three-level current advertisement input: ground or unconnected for default, 500-kΩ pullup to VDD for 1.5 A, 10-kΩ pullup to VDD for 3.0 A. · p. 3
4 PORT
Port mode sampled when VDD is active: pull up to VDD for DFP, leave unconnected for DRP, pull down or tie to GND for UFP. · p. 3
5 VBUS_DET
VBUS detection input for UFP attachment; connect system VBUS through one external 900-kΩ resistor. · p. 3
6 VCONN_FAULT
Asserted low when a VCONN over-current fault is detected. · p. 3
7 OUT1
Communicates detected Type-C current in UFP mode: high for default, low for medium or high current. · p. 3
8 OUT2
Communicates detected Type-C current in UFP mode: high for default or medium, low for high current. · p. 3
9 ID
Asserted low when CC pins detect attachment while operating as a source. · p. 3
10 GND
Ground. · p. 3
11 DIR
Detected plug orientation: high for Type-C plug position 2, low for position 1. · p. 3
12 VDD
Positive supply voltage. · p. 3

Ordering codes, by the datasheet

4
TUSB321AIRWBR
X2QFN (RWB) | 12 · 3000, LARGE T&R; -40 to 85 °C; NIPDAU · p. 16
TUSB321AIRWBR.A
X2QFN (RWB) | 12 · 3000, LARGE T&R; -40 to 85 °C; NIPDAU · p. 16
TUSB321AIRWBRG4
X2QFN (RWB) | 12 · 3000, LARGE T&R; -40 to 85 °C; NIPDAU · p. 16
TUSB321AIRWBRG4.A
X2QFN (RWB) | 12 · 3000, LARGE T&R; -40 to 85 °C; NIPDAU · p. 16

Open-source boards using it

1
  • 2 layers131.5 × 83.5 mmBadge esp32-s3, the printed circuit board in 3D

    Badge esp32-s3

    BYU-I-eBadge/e-badge

    A hackable eBadge platform for students — a customizable, programmable electronics badge designed for hands-on learning and creative exploration throughout their academic journey.

    214 parts2MIT

Parts like it

3

Questions

Is there a KiCad symbol and footprint for the TUSB321AIRWBR?

Yes. The symbol is Interface_USB:TUSB321 and the footprint Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TUSB321AIRWBR?

X2-QFN-12(1.6x1.6), with 12 pins. Its footprint is drawn on this page.

Where is the TUSB321AIRWBR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TUSB321AIRWBR?

JLCPCB lists it as part C2674046, with 3,692 in stock; the sellers' links on this page open their listings.

What can replace the TUSB321AIRWBR?

Parts like it in the library: the TUSB322IRWBR by Texas Instruments, the TUSB320IRWBR by Texas Instruments and the TUSB320RWBR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TUSB321AIRWBR?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.