Skip to the content

TUSB320LAIRWBR

Texas InstrumentsExtended

-40℃~+85℃ 2.7V~5V 3A 70uA I2C Not supported Not supported Programmable charging current X2-QFN-12(1.6x1.6) USB Converters ROHS

Part id
ti/TUSB320LAIRWBR
Category
Battery Management
Package
X2-QFN-12(1.6x1.6)
Pins
12
In stock
5,144 at JLCPCB (C132554)
Used on
14 open-source boards

Overview

The TUSB320LAIRWBR is a battery Management made by Texas Instruments in a X2-QFN-12(1.6x1.6) package with 12 pins. -40℃~+85℃ 2.7V~5V 3A 70uA I2C Not supported Not supported Programmable charging current X2-QFN-12(1.6x1.6) USB Converters ROHS.

PCBKit's library has its KiCad symbol (Interface_USB:TUSB320, from KiCad's library) and its footprint (Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mm, from KiCad's library), ready for a KiCad board. 5,144 are in stock at JLCPCB (part C132554). 14 open-source boards in 11 repositories on GitHub use it.

Symbol

1CC12CC23PORT4VBUS_DET5ADDR6INT/OUT37SDA/OUT18SCL/OUT29ID10GND11EN12VDD
Interface_USB:TUSB320From KiCad's library

Footprint

Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mmFrom KiCad's library

From the datasheet

11
Supply, least
2.7 V · VDD, recommended operating min · p. 4
Supply, most
5 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
6 V · VDD, absolute max · p. 4
Works from
-40 °C · TA, operating free-air min · p. 4
Works up to
85 °C · TA, operating free-air max · p. 4
Takes working
70 µA · VDD, active UFP typical; 4.5 V, ADDR = NC, PORT = L · p. 5
Takes asleep
40 nA · VDD, shutdown typical; 4.5 V, EN_N = H · p. 5
Junction to air (RWB (X2QFN))
169.3 K/W · junction-to-ambient · p. 4
Junction to case (RWB (X2QFN))
68.1 K/W · junction-to-case top · p. 4
Junction to board (RWB (X2QFN))
83.4 K/W · junction-to-board · p. 4
Supply, least
2.75 V · VDD, recommended operating min · p. 22

What it is and has

6
USB Type-C specification
1.1 · p. 1
Current advertisement and detection
Up to 3 A · p. 1
I2C clock
Up to 400 kHz · p. 1
Package
X2QFN (12), 1.60mm x 1.60mm · p. 1
Accessory support
Audio and debug in UFP, DFP and DRP modes · p. 11
DRP preferences
Try.SRC and Try.SNK · p. 11

Around it

6
res 900-kΩ
between VBUS and VBUS_DET; Required external series resistor for VBUS detection. · p. 3
res 200 kΩ
between INT_N/OUT3 and VDD; Typical external open-drain output pullup; pull up to device VDD to avoid back-driving when VDD is off. · p. 6
res 4.7 kΩ
between PORT and VDD; Typical external tri-level input pullup when high configuration is desired. · p. 6
cap 100-nF
between VDD and GND; Place near VDD. · p. 22
res 200-kΩ
between ID and VDD; External pullup for the open-drain ID output. · p. 22
res 900-kΩ
between VBUS_DET and VBUS; Required to protect VBUS_DET from high VBUS voltage. · p. 22

Specifications

66
ParameterConditionsAs printedPage
Supply voltage VDDmin -0.3 · max 6 V4
Control pinsPORT, ADDR, ID, EN_N, INT_N/OUT3; maximum VDD + 0.3 Vmin -0.3 V4
Control pinsCC1, CC2min -0.3 · max 6 V4
Control pinsSDA/OUT1, SCL/OUT2; maximum VDD + 0.3 Vmin -0.3 V4
Control pinsVBUS_DETmin -0.3 · max 4 V4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; rating ±3000 Vmax 3000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; rating ±1500 Vmax 1500 V4
Supply voltage range VDDmin 2.7 · max 5 V4
System VBUS voltage VBUSNominal 5 Vmin 4 · typ 5 · max 28 V4
TUSB320HAI and TUSB320LAI Operating free air temperature range TATUSB320LAI; nominal 25 °Cmin -40 · typ 25 · max 85 °C4
Junction-to-ambient thermal resistance RθJARWB (X2QFN), 12 PINStyp 169.3 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)RWB (X2QFN), 12 PINStyp 68.1 °C/W4
Junction-to-board thermal resistance RθJBRWB (X2QFN), 12 PINStyp 83.4 °C/W4
Junction-to-top characterization parameter ψJTRWB (X2QFN), 12 PINStyp 2.2 °C/W4
Junction-to-board characterization parameter ψJBRWB (X2QFN), 12 PINStyp 83.4 °C/W4
Current consumption in unattached mode when port is unconnected and waiting for connection. IUNATTACHED_UFPVDD = 4.5 V, EN_N (TUSB320LA) = L, ADDR = NC, PORT = Ltyp 70 uA5
Current consumption in active mode. IACTIVE_UFPVDD = 4.5 V, EN_N (TUSB320LA) = L, ADDR = NC, PORT = Ltyp 70 uA5
Leakage current when VDD is supplied, but the TUSB320 device is not enabled. ISHUTDOWNVDD = 4.5 V, EN_N (TUSB320LA) = Htyp 0.04 uA5
Pulldown resistor when in dead-battery mode. RCC_DBmin 4.1 · typ 5.1 · max 6.1 kΩ5
Pulldown resistor when in UFP or DRP mode. RCC_Dmin 4.6 · typ 5.1 · max 5.6 kΩ5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising default current source capability. VUFP_CC_USBmin 0.25 · max 0.61 V5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising medium (1.5-A) current source capability. VUFP_CC_MEDmin 0.7 · max 1.16 V5
Voltage level range for detecting a DFP attach when configured as a UFP and DFP is advertising high (3-A) current source capability. VUFP_CC_HIGHmin 1.31 · max 2.04 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising default current source capability. VTH_DFP_CC_USBmin 1.51 · typ 1.6 · max 1.64 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising medium current (1.5-A) source capability. VTH_DFP_CC_MEDmin 1.51 · typ 1.6 · max 1.64 V5
Voltage threshold for detecting a UFP attach when configured as a DFP and advertising high current (3.0-A) source capability. VTH_DFP_CC_HIGHmin 2.46 · typ 2.6 · max 2.74 V5
Default mode pullup current source when operating in DFP or DRP mode. ICC_DEFAULT_Pmin 64 · typ 80 · max 96 uA5
Medium (1.5-A) mode pullup current source when operating in DFP or DRP mode. ICC_MED_Pmin 166 · typ 180 · max 194 uA5
High (3-A) mode pullup current source when operating in DFP or DRP mode. ICC_HIGH_PVDD must be 3.5 V or greater to advertise 3 A current.min 304 · typ 330 · max 356 uA5
Low-level control signal input voltage (PORT, ADDR, EN_N, EN) VILPORT, ADDR, EN_Nmax 0.4 V5
High-level input current IIHmin -20 · max 20 uA5
Low-level input current IILmin -10 · max 10 uA5
Current Leakage on ID pin IID_LEAKAGEVDD = 0 V; ID = 5 Vmax 10 uA5
Internal pullup resistance for EN_N for TUSB320LA REN_NTUSB320LAtyp 1.1 MΩ5
Internal pullup resistance (PORT, ADDR) RpuRemoved after the device has sampled EN_N = low.typ 588 kΩ5
Internal pulldown resistance (PORT, ADDR) RpdRemoved after the device has sampled EN_N = low.typ 1.1 MΩ5
Low-level signal output voltage (open-drain) (INT_N/OUT3, ID) VOLIOL = –1.6 mAmax 0.4 V5
External pullup resistor on open drain IOs (INT_N/OUT3, ID) Rp_ODexttyp 200 kΩ6
Tri-level input external pullup resistor (PORT, ADDR) Rp_TLexttyp 4.7 kΩ6
Supply range for I2C (SDA/OUT1, SCL/OUT2) VDD_I2Cmin 1.65 · typ 1.8 · max 3.6 V6
High-level signal voltage VIHI2C - SDA/OUT1, SCL/OUT2min 1.05 · max 3.6 V6
Low-level signal voltage VILI2C - SDA/OUT1, SCL/OUT2max 0.4 V6
Low-level signal output voltage (open drain) VOLI2C - SDA/OUT1, SCL/OUT2; IOL = –1.6 mAmax 0.4 V6
VBUS threshold range VBUS_THRSee Figure 1min 2.95 · typ 3.3 · max 3.8 V6
External resistor between VBUS and VBUS_DET pin RVBUSmin 855 · typ 887 · max 920 KΩ6
Internal pulldown resistance for VBUS_DET RVBUS_PDtyp 95 KΩ6
Data setup time tSU:DATI2C (SDA, SCL)min 100 ns6
Data hold time tHD;DATI2C (SDA, SCL)min 10 ns6
Set-up time, SCL to start condition tSU:STAI2C (SDA, SCL)min 0.6 us6
Hold time (repeated), start condition to SCL tHD:STAI2C (SDA, SCL)min 0.6 us6
Set up time for stop condition tSU:STOI2C (SDA, SCL)min 0.6 us6
Bus free time between a stop and start condition tBUFI2C (SDA, SCL)min 1.3 us6
Data valid time tVD;DATI2C (SDA, SCL)max 0.9 us6
Data valid acknowledge time tVD;ACKI2C (SDA, SCL)max 0.9 us6
SCL clock frequency; I2C mode for local I2C control fSCLmax 400 kHz6
Rise time of both SDA and SCL signals trmax 300 ns6
Fall time of both SDA and SCL signals tfmax 300 ns6
Total capacitive load for each bus line when operating at ≤ 100 kHz CBUS_100KHZmax 400 pF6
Total capacitive load for each bus line when operating at 400 kHz CBUS_400KHzmax 100 pF6
Power on default of CC1 and CC2 voltage debounce time tCCCB_DEFAULTDEBOUCE register = 2'b00typ 168 ms6
Debounce of VBUS_DET pin after valid VBUS_THR tVBUS_DBtyp 2 ms6
Power-on default of percentage of time DRP advertises DFP during a tDRP tDRP_DUTY_CYCLEDRP_DUTY_CYCLE register = 2'b00typ 30 %6
The period during which the TUSB320HA or the TUSB320LA in DFP mode completes a DFP to UFP and back advertisement. tDRPTUSB320LAmin 50 · typ 75 · max 100 ms6
Time from TUSB320LA EN_N low or TUSB320HA EN high and VDD active to I2C access available tI2C_ENTUSB320LA EN_N low and VDD activemax 100 ms6
Soft reset duration tSOFT_RESETmin 26 · typ 49 · max 95 ms6

Pins, by the datasheet

12
1 CC1
Type-C configuration channel signal 1. · p. 3
2 CC2
Type-C configuration channel signal 2. · p. 3
3 PORT
Tri-level port mode input sampled when EN_N is asserted low with VDD active and after I2C_SOFT_RESET; pull up to VDD for DFP, leave unconnected for DRP, or pull down or tie to GND for UFP. · p. 3
4 VBUS_DET
Detects system VBUS for UFP attachment; connect to 5-V to 28-V system VBUS through one external 900-kΩ resistor. · p. 3
5 ADDR
Tri-level mode input: high enables I2C address 0x67, low enables I2C address 0x47, and unconnected selects GPIO mode; pull up to VDD for high. · p. 3
6 INT_N/OUT3
Active-low interrupt indicating register changes in I2C mode; in GPIO mode, low indicates audio accessory detection. · p. 3
7 SDA/OUT1
I2C data when ADDR is high or low; open-drain Type-C current detection output in UFP GPIO mode. · p. 3
8 SCL/OUT2
I2C clock when ADDR is high or low; open-drain Type-C current detection output in UFP GPIO mode. · p. 3
9 ID
Asserted low when CC pins detect device attachment while operating as a source in DFP or DRP mode. · p. 3
10 GND
Ground. · p. 3
11 EN_N
Active-low enable with internal pullup to VDD; if externally controlled, hold low for at least 50 ms after VDD reaches its valid voltage. · p. 3
12 VDD
Positive supply voltage; VDD must ramp within 25 ms or less. · p. 3

Ordering codes, by the datasheet

4
TUSB320LAIRWBR
X2QFN (RWB) · 12 pins; 3000 | LARGE T&R; operating temperature -40 to 85 °C; Level-2-260C-1 YEAR · p. 31
TUSB320LAIRWBR.A
X2QFN (RWB) · 12 pins; 3000 | LARGE T&R; operating temperature -40 to 85 °C; Level-2-260C-1 YEAR · p. 31
TUSB320LAIRWBRG4
X2QFN (RWB) · 12 pins; 3000 | LARGE T&R; operating temperature -40 to 85 °C; Level-1-260C-UNLIM · p. 31
TUSB320LAIRWBRG4.A
X2QFN (RWB) · 12 pins; 3000 | LARGE T&R; operating temperature -40 to 85 °C; Level-1-260C-UNLIM · p. 31

Open-source boards using it

14See all 14
  • 4 layers52 × 52 mmMoto gps rev a1, the printed circuit board in 3D

    Moto gps rev a1

    mx3353672833-debug/moto-gps-waveshare

    MOTO GPS · Waveshare ESP32-S3 1.75C 圆屏导航 + iPhone App | Author: Maler X | Noncommercial, attribution required | Experimental

    112 parts529
  • 2 layers297 × 102.4 mmEmiuet, the printed circuit board in 3D

    Emiuet

    emnyeca/emiuet

    The thirteen positions preserve familiar guitar-derived voicings without forcing octave shifts or omissions. Expressive controls are deliberately constrained so that performance remains predictable: Pitch Bend is…

    275 parts2
  • 4 layers80 × 80 mmQsbc zero, the printed circuit board in 3D

    Qsbc zero

    qfreiman/qsbc-zero

    Single Board Computer based on the i.MX6ULL

    243 parts1GPL-3.0
  • 4 layers100 × 90 mmNexus pear reva, the printed circuit board in 3D

    Nexus pear reva

    aminewe898/nexus-pear-reva

    NEXUS PEAR Rev A hardware design, schematics, PCB, manufacturing review exports and engineering documentation

    117 partsMIT
  • 2 layers141 × 90.9 mmHaptic bracelet, the printed circuit board in 3D

    Haptic bracelet

    earlynerd/ELRS-haptics

    Battery-powered attitude feedback for FPV flying, with eight haptic actuators around each wrist. An ESP32-C6 receives telemetry over ESP-NOW and controls eight M2003FC1AE/DRV2625 pods using the music robot's UART ring…

    269 parts
  • 8 layers40 × 94 mmFD MAIN-01, the printed circuit board in 3D

    FD MAIN-01

    Fairank/FieldDock

    Compact iPhone companion hardware: editable PCB, mechanical CAD and portable firmware. Engineering prototype; original work available for noncommercial use.

    424 parts
  • 2 layers70 × 50 mmStorage failed, the printed circuit board in 3D

    Storage failed

    IgorCulafic/PCBSmith

    Open-source PCB design tools: KiCad workflows, automatic routing, design review and laser fabrication. Working toward plain-language circuit-to-board design.

    104 partsAGPL-3.0
  • 2 layers90 × 30.3 mmIntegrated25, the printed circuit board in 3D

    Integrated25

    juicebox6030/Nova-Link

    NOVA-LINK is an open, low-latency wireless communication protocol and firmware stack designed for use in real-time live event environments.

    178 partsGPL-3.0

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the TUSB320LAIRWBR?

Yes. The symbol is Interface_USB:TUSB320 and the footprint Package_DFN_QFN:Texas_X2QFN-12_1.6x1.6mm_P0.4mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TUSB320LAIRWBR?

X2-QFN-12(1.6x1.6), with 12 pins. Its footprint is drawn on this page.

Where is the TUSB320LAIRWBR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TUSB320LAIRWBR?

JLCPCB lists it as part C132554, with 5,144 in stock; the sellers' links on this page open their listings.

What can replace the TUSB320LAIRWBR?

Parts like it in the library: the TUSB320HAIRWBR by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TUSB320LAIRWBR?

14 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.