TUSB1046-DCIRNQT
Texas InstrumentsExtended
0℃~+70℃ 300ps 3V~3.6V 4 4pF 5Ω WQFN-40-EP(4x6) Analog Switches, Multiplexers ROHS
- Part id
- ti/TUSB1046-DCIRNQT
- Category
- Analog Switches, Multiplexers
- Package
- WQFN-40-EP(4x6)
- Pins
- 41
- In stock
- 37 at JLCPCB (C2652434)
Overview
The TUSB1046-DCIRNQT is an analog Switches, Multiplexer made by Texas Instruments in a WQFN-40-EP(4x6) package with 41 pins. 0℃~+70℃ 300ps 3V~3.6V 4 4pF 5Ω WQFN-40-EP(4x6) Analog Switches, Multiplexers ROHS.
PCBKit's library has its KiCad symbol (TUSB1046-DCIRNQ:TUSB1046-DCIRNQ, from Antmicro) and its footprint (wqfn-40-1ep-6x3mm-pitch0-4mm-ep4-7x2-7mm:WQFN-40_1EP_6x3mm_Pitch0.4mm_EP4.7x2.7mm, from Antmicro), ready for a KiCad board. 37 are in stock at JLCPCB (part C2652434).
Symbol
Footprint
From the datasheet
10- Supply, least
- 3 V · VCC, recommended operating min · p. 5
- Supply, most
- 3.6 V · VCC, recommended operating max · p. 5
- Supply, absolute maximum
- 4 V · VCC, absolute max · p. 5
- Works from
- 0 °C · Operating free-air temperature min, TUSB1046-DCI · p. 5
- Works up to
- 70 °C · Operating free-air temperature max, TUSB1046-DCI · p. 5
- Junction, hottest
- 125 °C · Junction temperature absolute max · p. 5
- Junction to air (RNQ (WQFN))
- 37.6 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to case (RNQ (WQFN))
- 20.7 K/W · Junction-to-case (top) thermal resistance · p. 5
- Junction to board (RNQ (WQFN))
- 9.5 K/W · Junction-to-board thermal resistance · p. 5
- Data rate, most
- 10 Gbit/s · USB 3.1 Gen 1/Gen 2 max · p. 1
What it is and has
9- USB
- USB 3.1 Gen 1/Gen 2 up to 10 Gbps · p. 1
- DisplayPort
- DisplayPort 1.4 up to 8.1 Gbps (HBR3) · p. 1
- Lane configuration
- USB 3.1 SSP + 2 DisplayPort lanes · p. 1
- Lane configuration
- 4 DisplayPort lanes · p. 1
- Equalization
- Linear redriver with up to 14 dB equalization · p. 1
- Configuration
- GPIO or I2C · p. 1
- Hot plug
- Hot-plug capable · p. 1
- Package
- 4 mm × 6 mm, 0.4 mm pitch WQFN · p. 1
- DisplayPort link training
- Transparent · p. 1
Around it
6- res 2-M ohm
- between SBU1 and GND; Recommended; DC couple SBU1 to the Type-C receptacle. · p. 4
- res 2-M ohm
- between SBU2 and GND; Recommended; DC couple SBU2 to the Type-C receptacle. · p. 4
- res 100K
- between AUXp and GND; Required in addition to the AC coupling capacitor. · p. 4
- res 100K
- between AUXn and DP_PWR; Required in addition to the AC coupling capacitor; DP_PWR is 3.3V. · p. 4
- res 820 Ω
- between SDA and V(I2C); Typical external pull-up for FM+ (1MHz), bus capacitance 150 pF; range 620–910 Ω. · p. 6
- res 1500 Ω
- between SDA and V(I2C); Typical external pull-up for FM (400kHz), bus capacitance 150 pF; range 620–2200 Ω. · p. 6
Specifications
129| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply Voltage Range(2), VCC VCC | min -0.3 · max 4 V | 5 | |
| Voltage Range at any input or output pin | Differential voltage between positive and negative inputs | max 2.5 V | 5 |
| Voltage Range at any input or output pin | Voltage at differential inputs; maximum VCC + 0.5 V | min -0.5 V | 5 |
| Voltage Range at any input or output pin | CMOS Inputs; maximum VCC + 0.5 V | min -0.5 V | 5 |
| Maximum junction temperature, TJ TJ | max 125 °C | 5 | |
| Storage temperature, Tstg Tstg | min -65 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±5000 V | max 5000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1500 V | max 1500 V | 5 |
| Main power supply VCC | min 3 · typ 3.3 · max 3.6 V | 5 | |
| Supply Ramp Requirement VCC | max 100 ms | 5 | |
| Supply that external resistors are pulled up to on SDA and SCL V(12C) | min 1.7 · max 3.6 V | 5 | |
| Supply Noise on VCC pins V(PSN) | max 100 mV | 5 | |
| Operating free-air temperature TA | TUSB1046-DCI | min 0 · max 70 °C | 5 |
| Junction-to-ambient thermal resistance RθJA | RNQ (WQFN), 40 PINS | typ 37.6 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | RNQ (WQFN), 40 PINS | typ 20.7 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | RNQ (WQFN), 40 PINS | typ 9.5 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | RNQ (WQFN), 40 PINS | typ 0.2 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | RNQ (WQFN), 40 PINS | typ 9.4 °C/W | 5 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | RNQ (WQFN), 40 PINS | typ 2.3 °C/W | 5 |
| Average active power USB Only PCC(ACTIVE-USB) | Link in U0 with GEN2 data transmission; EN, EQ cntrl pins = NC; k28.5 pattern at 10 Gbps; VID = 1000 mVPP; CTL1 = L; CTL0 = H | typ 335 mW | 6 |
| Average active power USB + 2 Lane DP PCC(ACTIVE-USB-DP1) | Link in U0 with GEN2 data transmission; EN, EQ cntrl pins = NC; k28.5 pattern at 10 Gbps; VID = 1000 mVPP; CTL1 = H; CTL0 = H | typ 634 mW | 6 |
| Average active power 4 Lane DP Only PCC(ACTIVE--DP) | Four active DP lanes operating at 8.1Gbps; CTL1 = H; CTL0 = L | typ 660 mW | 6 |
| Average power with no connection PCC(NC-USB) | No GEN1 device is connected to TXP/TXN; CTL1 = L; CTL0 = H | typ 2.4 mW | 6 |
| Average power in U2/U3 PCC(U2U3) | Link in U2 or U3 USB Mode Only; CTL1 = L; CTL0 = H | typ 3 mW | 6 |
| Device Shutdown PCC(SHUTDOWN) | CTL1 = L; CTL0 = L; I2C_EN = 0 | typ 0.85 mW | 6 |
| High level input current IIH | 4-State CMOS Inputs(EQ[1:0], SSEQ[1:0], DPEQ[1:0], I2C_EN); VCC = 3.6 V; VIN = 3.6 V | min 20 · max 80 uA | 6 |
| Low level input current IIL | 4-State CMOS Inputs(EQ[1:0], SSEQ[1:0], DPEQ[1:0], I2C_EN); VCC = 3.6 V; VIN = 0 V | min -160 · max -40 uA | 6 |
| Threshold 0 / R 4-Level VTH | 4-State CMOS Inputs; VCC = 3.3 V | typ 0.55 V | 6 |
| Threshold R/ Float 4-Level VTH | 4-State CMOS Inputs; VCC = 3.3 V | typ 1.65 V | 6 |
| Threshold Float / 1 4-Level VTH | 4-State CMOS Inputs; VCC = 3.3 V | typ 2.7 V | 6 |
| Internal pull-up resistance RPU | 4-State CMOS Inputs | typ 35 kΩ | 6 |
| Internal pull-down resistance RPD | 4-State CMOS Inputs | typ 95 kΩ | 6 |
| High-level input voltage VIH | 2-State CMOS Input (CTL0, CTL1, FLIP, CAD_SNK, HPDIN) | min 2 · max 3.6 V | 6 |
| Low-level input voltage VIL | 2-State CMOS Input (CTL0, CTL1, FLIP, CAD_SNK, HPDIN) | min 0 · max 0.8 V | 6 |
| Internal pull-down resistance for CTL1 RPD | 2-State CMOS Input | typ 500 kΩ | 6 |
| Internal pull-down resistance for CAD_SNK (pin 29), and HPDIN (pin 32) R(ENPD) | 2-State CMOS Input | typ 150 kΩ | 6 |
| High-level input current IIH | 2-State CMOS Input; VIN = 3.6 V | min -25 · max 25 uA | 6 |
| Low-level input current IIL | 2-State CMOS Input; VIN = GND, VCC = 3.6 V | min -25 · max 25 uA | 6 |
| High-level input voltage VIH | I2C Control Pins SCL, SDA; I2C_EN = 0; minimum 0.7 x V(I2C) | max 3.6 V | 6 |
| Low-level input voltage VIL | I2C Control Pins SCL, SDA; I2C_EN = 0; maximum 0.3 x V(I2C) | min 0 V | 6 |
| Low-level output voltage VOL | I2C Control Pins SCL, SDA; I2C_EN = 0; IOL = 3 mA | min 0 · max 0.4 V | 6 |
| Low-level output current IOL | I2C Control Pins SCL, SDA; I2C_EN = 0; VOL = 0.4 V | min 20 mA | 6 |
| Input current on SDA pin II(I2C) | 0.1 x V(I2C) < Input voltage < 3.3 V | min -10 · max 10 uA | 6 |
| Input capacitance CI(I2C) | I2C Control Pins SCL, SDA | max 10 pF | 6 |
| I2C bus capacitance for FM+ (1MHz) C(I2C_FM+_BUS) | max 150 pF | 6 | |
| I2C bus capacitance for FM (400kHz) C(I2C_FM_BUS) | max 150 pF | 6 | |
| External resistors on both SDA and SCL when operating at FM+ (1MHz) R(EXT_I2C_FM+) | C(I2C_FM+_BUS) = 150 pF | min 620 · typ 820 · max 910 Ω | 6 |
| External resistors on both SDA and SCL when operating at FM (400kHz) R(EXT_I2C_FM) | C(I2C_FM_BUS) = 150 pF | min 620 · typ 1500 · max 2200 Ω | 6 |
| Input differential peak-peak voltage swing linear dynamic range V(RX-DIFF-PP) | USB Gen 2 Differential Receiver (RX1P/N, RX2P/N, SSTXP/N); AC-coupled differential peak-to-peak signal measured post CTLE through a reference channel | typ 2000 mVpp | 7 |
| Common-mode voltage bias in the receiver (DC) V(RX-DC-CM) | USB Gen 2 Differential Receiver | min 0 · max 2 V | 7 |
| Differential input impedance (DC) R(RX-DIFF-DC) | USB Gen 2 Differential Receiver; Present after a GEN2 device is detected on TXP/TXN | min 72 · max 120 Ω | 7 |
| Receiver DC common mode impedance R(RX-CM-DC) | USB Gen 2 Differential Receiver; Present after a GEN2 device is detected on TXP/TXN | min 18 · max 30 Ω | 7 |
| Common-mode input impedance with termination disabled (DC) Z(RX-HIGH-IMP-DC-POS) | USB Gen 2 Differential Receiver; Present when no GEN2 device is detected on TXP/TXN; measured over 0-500mV with respect to GND | min 25 kΩ | 7 |
| Input differential peak-to-peak signal detect assert level V(SIGNAL-DET-DIFF-PP) | At 10 Gbps, no input loss, PRBS7 pattern | typ 80 mV | 7 |
| Input differential peak-to-peak signal detect de-assert Level V(RX-IDLE-DET-DIFF-PP) | At 10 Gbps, no input loss, PRBS7 pattern | typ 60 mV | 7 |
| Low frequency periodic signaling (LFPS) detect threshold V(RX-LFPS-DET-DIFF-PP) | Below the minimum is squelched | min 100 · max 300 mV | 7 |
| Peak RX AC common-mode voltage V(RX-CM-AC-P) | Measured at package pin | max 150 mV | 7 |
| RX input capacitance to GND C(RX) | At 5 GHz | typ 0.5 · max 1 pF | 7 |
| Differential return Loss RL(RX-DIFF) | 50 MHz – 1.25 GHz at 90 Ω | typ -19 dB | 7 |
| Differential return Loss RL(RX-DIFF) | 5 GHz at 90 Ω | typ -10 dB | 7 |
| Common-mode return loss RL(RX-CM) | 50 MHz – 5 GHz at 90 Ω | typ -10 dB | 7 |
| Receiver equalization for upstream facing port EQ(SS_TX) | SSEQ[1:0] at 5 GHz | typ 11 dB | 7 |
| Receiver equalization for downstream facing ports EQ(SS_RX) | EQ[1:0] at 5 GHz | typ 9 dB | 7 |
| Transmitter dynamic differential voltage swing range. VTX(DIFF-PP) | USB Gen 2 Differential Transmitter (TX1P/N, TX2P/N, SSRXP/N) | typ 1600 mVPP | 7 |
| Amount of voltage change allowed during receiver detection VTX(RCV-DETECT) | USB Gen 2 Differential Transmitter | max 600 mV | 7 |
| Transmitter idle common-mode voltage change while in U2/U3 and not actively transmitting LFPS VTX(CM-IDLE-DELTA) | USB Gen 2 Differential Transmitter | min -600 · max 600 mV | 7 |
| Common-mode voltage bias in the transmitter (DC) VTX(DC-CM) | USB Gen 2 Differential Transmitter | min 0 · max 2 V | 7 |
| Tx AC common-mode voltage active VTX(CM-AC-PP-ACTIVE) | Max mismatch from Txp + Txn for both time and amplitude | max 100 mVPP | 7 |
| AC electrical idle differential peak-to-peak output voltage VTX(IDLE-DIFF-AC-PP) | At package pins | min 0 · max 10 mV | 7 |
| DC electrical idle differential output voltage VTX(IDLE-DIFF-DC) | At package pins after low pass filter to remove AC component | min 0 · max 14 mV | 7 |
| Absolute DC common-mode voltage between U1 and U0 VTX(CM-DC-ACTIVE-IDLE-DELTA) | At package pin | max 200 mV | 7 |
| Differential impedance of the driver RTX(DIFF) | USB Gen 2 Differential Transmitter | min 75 · max 120 Ω | 7 |
| AC coupling capacitor CAC(COUPLING) | USB Gen 2 Differential Transmitter | min 75 · max 265 nF | 7 |
| Common-mode impedance of the driver RTX(CM) | Measured with respect to AC ground over 0–500 mV | min 18 · max 30 Ω | 7 |
| TX short circuit current ITX(SHORT) | TX± shorted to GND | max 67 mA | 7 |
| TX input capacitance for return loss CTX(PARASITIC) | At package pins, at 5 GHz | max 1.25 pF | 7 |
| Differential return loss RLTX(DIFF) | 50 MHz – 1.25 GHz at 90 Ω | typ -15 dB | 7 |
| Differential return loss RLTX(DIFF) | 5 GHz at 90 Ω | typ -13 dB | 7 |
| Common-mode return loss RLTX(CM) | 50 MHz – 5 GHz at 90 Ω | typ -13 dB | 7 |
| Differential crosstalk between TX and RX signal pairs Crosstalk | at 5 GHz | typ -30 dB | 8 |
| Low frequency 1-dB compression point C(P1dB-LF) | at 100 MHz, 200 mVPP < VID < 2000 mVPP | typ 1300 mVPP | 8 |
| High frequency 1-dB compression point C(P1dB-HF) | at 5 GHz, 200 mVPP < VID < 2000 mVPP | typ 1000 mVPP | 8 |
| Low frequency cutoff fLF | 200 mVPP< VID < 2000 mVPP | typ 20 · max 50 kHz | 8 |
| TX output deterministic jitter | 200 mVPP < VID < 2000 mVPP, PRBS7, 10 Gbps | typ 0.11 UIpp | 8 |
| TX output deterministic jitter | 200 mVPP < VID < 2000 mVPP, PRBS7, 8.1 Gbps | typ 0.08 UIpp | 8 |
| TX output total jitter | 200 mVPP < VID < 2000 mVPP, PRBS7, 10 Gbps | typ 0.15 UIpp | 8 |
| TX output total jitter | 200 mVPP < VID < 2000 mVPP, PRBS7, 8.1 Gbps | typ 0.135 UIpp | 8 |
| Peak-to-peak input differential dynamic voltage range VID(PP) | DisplayPort Receiver (DP[3:0]p or DP[3:0]n) | typ 2000 V | 8 |
| Input common mode voltage VIC | DisplayPort Receiver (DP[3:0]p or DP[3:0]n) | min 0 · max 2 V | 8 |
| AC coupling capacitance C(AC) | DisplayPort Receiver (DP[3:0]p or DP[3:0]n) | min 75 · max 265 nF | 8 |
| Receiver equalization EQ(DP) | DisplayPort Receiver; DPEQ[1:0] at 4.05 GHz | max 14 dB | 8 |
| Data rate dR | DisplayPort Receiver; HBR3 | max 8.1 Gbps | 8 |
| Input termination resistance R(ti) | DisplayPort Receiver (DP[3:0]p or DP[3:0]n) | min 80 · typ 100 · max 120 Ω | 8 |
| TX short circuit current ITX(SHORT) | DisplayPort Transmitter; TX± shorted to GND | max 67 mA | 8 |
| Common-mode voltage bias in the transmitter (DC) VTX(DC-CM) | DisplayPort Transmitter (TX1p or TX1n, TX2p or TX2n, RX1p or RX1n, RX2p or RX2n) | min 0 · max 0 V | 8 |
| Output ON resistance RON | AUXp or AUXn and SBU1 or SBU2; VCC = 3.3V; VI = 0 to 0.4 V for AUXp; VI = 2.7 V to 3.6 V for AUXn | typ 5 · max 10 Ω | 8 |
| ON resistance mismatch within pair ΔRON | AUXp or AUXn and SBU1 or SBU2; VCC = 3.3 V; VI = 0 to 0.4 V for AUXP; VI = 2.7 V to 3.6 V for AUXN | max 2.5 Ω | 8 |
| ON resistance flatness (RON max – RON min) measured at identical VCC and temperature RON(FLAT) | AUXp or AUXn and SBU1 or SBU2; VCC = 3.3 V; VI = 0 to 0.4 V for AUXp; VI = 2.7 V to 3.6 V for AUXn | max 2 Ω | 8 |
| AUX Channel DC common mode voltage for AUXp and SBU1. V(AUXP_DC_CM) | VCC = 3.3 V | min 0 · max 0.4 V | 8 |
| AUX Channel DC common mode voltage for AUXn and SBU2 V(AUXN_DC_CM) | VCC = 3.3 V | min 2.7 · max 3.6 V | 8 |
| ON-state capacitance C(AUX_ON) | VCC = 3.3 V; CTL1 = 1; VI = 0 V or 3.3 V | typ 4 · max 7 pF | 8 |
| OFF-state capacitance C(AUX_OFF) | VCC = 3.3 V; CTL1 = 0; VI = 0 V or 3.3 V | typ 3 · max 6 pF | 8 |
| Delay from U0 to electrical idle tIDLEEntry | USB Gen 1; See Figure 7-4 | typ 10 ns | 8 |
| U1 exist time: break in electrical idle to the transmission of LFPS tIDELExit_U1 | USB Gen 1; See Figure 7-4 | typ 6 ns | 8 |
| U2/U3 exit time: break in electrical idle to transmission of LFPS tIDLEExit_U2U3 | USB Gen 1 | typ 10 us | 8 |
| RX detect interval while in Disconnect tRXDET_INTVL | USB Gen 1 | max 12 ms | 8 |
| Disconnect Exit Time tIDLEExit_DISC | USB Gen 1 | typ 10 us | 8 |
| Shutdown Exit Time tExit_SHTDN | USB Gen 1 | typ 1 ms | 8 |
| Differential Propagation Delay tDIFF_DLY | USB Gen 1; See Figure 7-3 | max 300 ps | 8 |
| Output Rise/Fall time (see Figure 7-5) tR, tF | 20%-80% of differential voltage measured 1.7 inch from the output pin | typ 35 ps | 9 |
| Output Rise/Fall time mismatch tRF_MM | 20%-80% of differential voltage measured 1.7 inch from the output pin | max 2.6 ps | 9 |
| Switch propagation delay tAUX_PD | AUXp or AUXn and SBU1 or SBU2; over operating free-air temperature range | max 400 ps | 9 |
| Switching time CTL1 to switch OFF. Not including TCTL1_DEBOUNCE. tAUX_SW_OFF | AUXp or AUXn and SBU1 or SBU2; over operating free-air temperature range | max 500 ns | 9 |
| Switching time CTL1 to switch ON tAUX_SW_ON | AUXp or AUXn and SBU1 or SBU2; over operating free-air temperature range | max 500 ns | 9 |
| Intra-pair output skew tAUX_INTRA | AUXp or AUXn and SBU1 or SBU2; over operating free-air temperature range | max 100 ps | 9 |
| Min overlap of CTL0 and CTL1 when transitioning from USB 3.1 only mode to 4-Lane DisplayPort mode or vice versa. tGP_USB_4DP | USB3.1 and DisplayPort mode transition requirement GPIO mode | min 4 us | 9 |
| CTL1 and HPDIN debounce time when transitioning from H to L. tCTL1_DEBOUNCE | CTL1 and HPDIN | min 2 · max 10 ms | 9 |
| I2C clock frequency fSCL | I2C (Refer to Figure 7-1) | max 1 MHz | 9 |
| Bus free time between START and STOP conditions tBUF | I2C (Refer to Figure 7-1) | min 0.5 us | 9 |
| Hold time after repeated START condition. After this period, the first clock pulse is generated tHDSTA | I2C (Refer to Figure 7-1) | min 0.26 us | 9 |
| Low period of the I2C clock tLOW | I2C (Refer to Figure 7-1) | min 0.5 us | 9 |
| High period of the I2C clock tHIGH | I2C (Refer to Figure 7-1) | min 0.26 us | 9 |
| Setup time for a repeated START condition tSUSTA | I2C (Refer to Figure 7-1) | min 0.26 us | 9 |
| Data hold time tHDDAT | I2C (Refer to Figure 7-1) | min 0 us | 9 |
| Data setup time tSUDAT | I2C (Refer to Figure 7-1) | min 50 ns | 9 |
| Rise time of both SDA and SCL signals tR | I2C (Refer to Figure 7-1) | max 120 ns | 9 |
| Fall time of both SDA and SCL signals tF | I2C (Refer to Figure 7-1); minimum is the expression 20 × (V(I2C)/5.5 V) | max 120 ns | 9 |
| Setup time for STOP condition tSUSTO | I2C (Refer to Figure 7-1) | min 0.26 us | 9 |
| Capacitive load for each bus line Cb | I2C (Refer to Figure 7-1) | max 150 pF | 9 |
Pins, by the datasheet
41- 1 VCC
- 3.3-V Power Supply. · p. 4
- 2 DPEQ1
- Along with DPEQ0 selects DisplayPort receiver equalization gain. · p. 4
- 3 SSEQ1
- Along with SSEQ0 sets USB receiver equalizer gain for upstream facing SSTXP/N. · p. 4
- 4 SSRXn
- Differential negative output for USB3.1 upstream facing port. · p. 4
- 5 SSRXp
- Differential positive output for USB3.1 upstream facing port. · p. 4
- 6 VCC
- 3.3-V Power Supply. · p. 4
- 7 SSTXn
- Differential negative input for USB3.1 upstream facing port. · p. 3
- 8 SSTXp
- Differential positive input for USB3.1 upstream facing port. · p. 3
- 9 DP0p
- DP differential positive input for DisplayPort Lane 0. · p. 3
- 10 DP0n
- DP differential negative input for DisplayPort Lane 0. · p. 3
- 11 SSEQ0/A0
- Along with SSEQ1 sets upstream USB receiver equalizer gain; also sets I2C address when I2C_EN is not 0; must be F or 0 when I2C_EN = F. · p. 4
- 12 DP1p
- DP differential positive input for DisplayPort Lane 1. · p. 3
- 13 DP1n
- DP differential negative input for DisplayPort Lane 1. · p. 3
- 14 DPEQ0/A1
- Along with DPEQ1 selects DisplayPort receiver equalization gain; also sets I2C address when I2C_EN is not 0. · p. 4
- 15 DP2p
- DP differential positive input for DisplayPort Lane 2. · p. 3
- 16 DP2n
- DP differential negative input for DisplayPort Lane 2. · p. 3
- 17 I2C_EN
- Programming mode select: 0 for GPIO, R for TI test mode with 3.3-V I2C, F for 1.8-V I2C, 1 for 3.3-V I2C. · p. 4
- 18 DP3p
- DP differential positive input for DisplayPort Lane 3. · p. 3
- 19 DP3n
- DP differential negative input for DisplayPort Lane 3. · p. 3
- 20 VCC
- 3.3-V Power Supply. · p. 4
- 21 FLIP/SCL
- Flip control when I2C_EN = 0; otherwise I2C clock, pulled up to the I2C controller supply. · p. 4
- 22 CTL0/SDA
- USB3.1 switch control when I2C_EN = 0; otherwise I2C data, pulled up to the I2C controller supply. · p. 4
- 23 CTL1/HPDIN
- Enables DisplayPort when high in GPIO mode; otherwise hot-plug detect input, disabling DP lanes after low for more than 2 ms while AUX-to-SBU remains closed. · p. 4
- 24 AUXp
- DisplayPort AUX positive I/O; AC couple to source and add 100K resistor to GND; routed to SBU1/2 according to orientation. · p. 4
- 25 AUXn
- DisplayPort AUX negative I/O; AC couple to source and add 100K resistor to DP_PWR (3.3V); routed to SBU1/2 according to orientation. · p. 4
- 26 SBU2
- DC couple to receptacle SBU2; 2-M ohm resistor to GND recommended. · p. 4
- 27 SBU1
- DC couple to receptacle SBU1; 2-M ohm resistor to GND recommended. · p. 4
- 28 VCC
- 3.3-V Power Supply. · p. 4
- 29 CAD_SNK/ RSVD1
- Reserved when I2C_EN is not 0; leave open if unused; in GPIO mode low enables AUX snooping and high disables it with all lanes active. · p. 4
- 30 RX1p
- Differential positive DisplayPort output or USB3.1 downstream facing port input. · p. 3
- 31 RX1n
- Differential negative DisplayPort output or USB3.1 downstream facing port input. · p. 3
- 32 HPDIN/ RSVD2
- Reserved when I2C_EN is not 0; leave open if unused; in GPIO mode hot-plug detect input, disabling DP lanes after low for more than 2 ms while AUX-to-SBU remains closed. · p. 4
- 33 TX1p
- Differential positive output for DisplayPort or USB 3.1 downstream facing port. · p. 3
- 34 TX1n
- Differential negative output for DisplayPort or USB3.1 downstream facing port. · p. 3
- 35 EQ1
- Along with EQ0 sets USB receiver equalizer gain for downstream facing RX1 and RX2. · p. 4
- 36 TX2n
- Differential negative output for DisplayPort or USB 3.1 downstream facing port. · p. 3
- 37 TX2p
- Differential positive output for DisplayPort or USB 3.1 downstream facing port. · p. 3
- 38 EQ0
- Along with EQ1 sets USB receiver equalizer gain for downstream facing RX1 and RX2. · p. 4
- 39 RX2n
- Differential negative DisplayPort output or USB3.1 downstream facing port input. · p. 3
- 40 RX2p
- Differential positive DisplayPort output or USB3.1 downstream facing port input. · p. 3
- Thermal Pad Thermal Pad
- Ground. · p. 4
Ordering codes, by the datasheet
4- TUSB1046-DCIRNQR
- WQFN (RNQ) | 40 · 3000 | LARGE T&R; operating temperature 0 to 70 °C · p. 41
- TUSB1046-DCIRNQR.B
- WQFN (RNQ) | 40 · 3000 | LARGE T&R; operating temperature 0 to 70 °C · p. 41
- TUSB1046-DCIRNQT
- WQFN (RNQ) | 40 · 250 | SMALL T&R; operating temperature 0 to 70 °C · p. 41
- TUSB1046-DCIRNQT.B
- WQFN (RNQ) | 40 · 250 | SMALL T&R; operating temperature 0 to 70 °C · p. 41
Questions
Is there a KiCad symbol and footprint for the TUSB1046-DCIRNQT?
Yes. The symbol is TUSB1046-DCIRNQ:TUSB1046-DCIRNQ and the footprint wqfn-40-1ep-6x3mm-pitch0-4mm-ep4-7x2-7mm:WQFN-40_1EP_6x3mm_Pitch0.4mm_EP4.7x2.7mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TUSB1046-DCIRNQT?
WQFN-40-EP(4x6), with 41 pins. Its footprint is drawn on this page.
Where is the TUSB1046-DCIRNQT datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TUSB1046-DCIRNQT?
JLCPCB lists it as part C2652434, with 37 in stock; the sellers' links on this page open their listings.