Skip to the content

TPS62086RLTR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 2.4MHz 2.5V~6V 3.3V 3A Buck Buck Built-in Fixed Yes VSON-7(2x2) DC-DC Converters ROHS

Part id
ti/TPS62086RLTR
Category
DC DC Converters
Package
VSON-7(2x2)
Pins
7
In stock
111 at JLCPCB (C2071344)
Used on
1 open-source board

Overview

The TPS62086RLTR is a DC DC Converter made by Texas Instruments in a VSON-7(2x2) package with 7 pins. -40℃~+125℃@(TJ) 1 2.4MHz 2.5V~6V 3.3V 3A Buck Buck Built-in Fixed Yes VSON-7(2x2) DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Celestial_Power_Switchmode:TI TPS62086RLT, from Altium's library) and its footprint (EasyEDA_Cloud:VSON-7_L2.0-W2.0-P0.5-TL, from EasyEDA), ready for a KiCad board. 111 are in stock at JLCPCB (part C2071344). 1 open-source board in 1 repository on GitHub use it.

Symbol

7VIN1EN2PG6SW3FB4VOS5GND
Celestial_Power_Switchmode:TI TPS62086RLTFrom Altium's library

Footprint

EasyEDA_Cloud:VSON-7_L2.0-W2.0-P0.5-TLFrom EasyEDA

From the datasheet

13
Supply, least
2.5 V · VIN, recommended operating min · p. 4
Supply, most
6 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
7 V · VIN, absolute maximum · p. 4
Junction, hottest
150 °C · Operating junction temperature, absolute max · p. 4
Takes working
17 µA · VIN, typical quiescent current, no load, device not switching · p. 5
Takes asleep
700 nA · VIN, typical shutdown current, EN low · p. 5
Gives
3 A · Rated output current · p. 1
Current limit
4.6 A · High-side FET switch current limit, typical · p. 5
Output
3.3 V · TPS62086 fixed output voltage · p. 3
Switches at
2.4 MHz · PWM switching frequency, typical, IOUT = 1 A · p. 5
Junction to air (RLT [VSON])
107.8 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (RLT [VSON])
66.2 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (RLT [VSON])
17.1 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

9
Control topology
DCS-Control · p. 1
Efficiency
Up to 95% · p. 1
Short-circuit protection
Hiccup · p. 1
Light load operation
Power save mode · p. 1
Duty cycle
100% for lowest dropout · p. 1
Output discharge
Supported · p. 1
Power good output
Supported · p. 1
Thermal protection
Thermal shutdown · p. 1
Package
2-mm × 2-mm VSON · p. 1

Around it

5
cap 10 μF
between VIN and GND; Low ESR multilayer ceramic input capacitor; place as close as possible to the pins. · p. 12
cap 22 μF
between VOUT and GND; Typical output capacitor; low ESR ceramic, X7R or X5R recommended. · p. 12
ind 0.47 µH
between SW and VOUT; Example power inductor, Coilcraft XFL4015-471ME, size 4 mm × 4 mm × 1.5 mm. · p. 10
res 0 Ω
between VOUT and FB; R1 connection for TPS62086; R2 is left open. · p. 10
res 1 MΩ
between VOUT and PG; Example power good pullup resistor, 1/16 W, 1%, size 0603. · p. 10

Specifications

45
ParameterConditionsAs printedPage
Voltage at Pins(2)VIN, FB, VOS, EN, PG; over operating free-air temperature rangemin -0.3 · max 7 V4
Voltage at Pins(2)SW (DC); maximum VIN + 0.3 Vmin -0.3 V4
Voltage at Pins(2)SW (AC, less than 100ns), while switchingmin -3 · max 11 V4
Temperature TJOperating Junctionmin -40 · max 150 °C4
Temperature TstgStoragemin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 V ratingmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; ±500 V ratingmax 500 V4
Input voltage range VINmin 2.5 · max 6 V4
Sink current at PG pin ISINK_PGmax 1 mA4
Pullup resistor voltage VPGmax 6 V4
Operating junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJARLT [VSON], 7 pinstyp 107.8 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)RLT [VSON], 7 pinstyp 66.2 °C/W4
Junction-to-board thermal resistance RθJBRLT [VSON], 7 pinstyp 17.1 °C/W4
Junction-to-top characterization parameter ψJTRLT [VSON], 7 pinstyp 2.1 °C/W4
Junction-to-board characterization parameter ψJBRLT [VSON], 7 pinstyp 17.1 °C/W4
Input voltage range VINTJ = –40 °C to 125 °Cmin 2.5 · max 6 V5
Quiescent current into VIN IQNo load, device not switching; TJ = –40 °C to 85 °C, VIN = 2.5 V to 5.5 V; typical at TJ = 25 °Ctyp 17 · max 25 uA5
Shutdown current into VIN ISDEN = Low; TJ = –40 °C to 85 °C, VIN = 2.5 V to 5.5 V; typical at TJ = 25 °Ctyp 0.7 · max 5 uA5
Undervoltage lockout threshold VUVLOVIN fallingmin 2.1 · typ 2.2 · max 2.3 V5
Undervoltage lockout hysteresis VUVLOVIN risingtyp 200 mV5
Thermal shutdown threshold TJSDTJ risingtyp 150 °C5
Thermal shutdown hysteresis TJSDTJ fallingtyp 20 °C5
High-level input voltage VIHVIN = 2.5 V to 6.0 Vmin 1 V5
Low-level input voltage VILVIN = 2.5 V to 6.0 Vmax 0.4 V5
Input leakage current into EN pin IEN,LKGEN = Hightyp 0.01 · max 0.16 uA5
Pulldown resistance at EN pin RPDEN = Lowtyp 400 kΩ5
Soft-start time tSSTime from EN high to 95% of VOUT nominaltyp 0.8 ms5
Power good threshold VPGVOUT rising, referenced to VOUT nominalmin 93 · typ 95 · max 98 %5
Power good threshold VPGVOUT falling, referenced to VOUT nominalmin 88 · typ 90 · max 93 %5
Low-level output voltage VPG,OLIsink = 1 mAmax 0.4 V5
Input leakage current into PG pin IPG,LKGVPG = 5.0 V, TJ = –40 °C to 85 °Ctyp 0.01 · max 0.16 uA5
Input leakage current into PG pin IPG,LKGVPG = 5.0 V, TJ = –40 °C to 125 °Ctyp 0.01 · max 0.25 uA5
Output voltage accuracy VOUTTPS62086; IOUT = 1 A, VIN ≥ VOUT + 1 V, PWM modemin -1 · max 1 %5
Output voltage accuracy VOUTTPS62086; IOUT = 0 A, VIN ≥ VOUT + 1 V, PSM modemin -1 · max 2.1 %5
Feedback regulation voltage(1) (2) VFBIOUT = 1A, VIN ≥ VOUT + 1 V, PWM mode; L = 0.47 uH, COUT = 22 uFmin 792 · typ 800 · max 808 mV5
Feedback regulation voltage(1) (2) VFBIOUT = 0 A, VIN ≥ VOUT + 1 V, PSM mode; L = 0.47 uH, COUT = 22 uFmin 792 · typ 800 · max 817 mV5
Feedback input leakage current IFB,LKGVFB = 1 Vtyp 0.01 · max 0.1 uA5
Output discharge resistor RDISEN = LOW, VOUT = 1.8 Vtyp 260 Ω5
Line regulationIOUT = 1 A, VIN = 2.5 V to 6.0 Vtyp 0.02 %/V5
Load regulationIOUT = 0.5 A to 3 Atyp 0.16 %/A5
High-side FET ON-resistance RDS(on)ISW = 500 mAtyp 31 · max 56 mΩ5
Low-side FET ON-resistance RDS(on)ISW = 500 mAtyp 23 · max 45 mΩ5
High-side FET switch current limit ILIMmin 3.7 · typ 4.6 · max 5.5 A5
PWM switching frequency fSWIOUT = 1 Atyp 2.4 MHz5

Pins, by the datasheet

7
1 EN
Pull high to enable or low to disable; typically 400 kΩ pulldown when disabled. · p. 3
2 PG
Power good output; pullup supply must not exceed 6 V. Leave floating if unused. · p. 3
3 FB
Feedback pin; connect to output voltage for this fixed output version. · p. 3
4 VOS
Output voltage sense; connect directly to the output capacitor. · p. 3
5 GND
Ground pin. · p. 3
6 SW
Switch pin of the power stage. · p. 3
7 VIN
Input voltage pin. · p. 3

Open-source boards using it

1
  • 2 layers32 × 65 mmZero3w, the printed circuit board in 3D

    Zero3w

    Techburst36/orangepi-zero3w-m2-carrier

    Open-source KiCad design for a PCIe-to-M.2 carrier board for the Orange Pi Zero 3W. Schematic and PCB are ERC/DRC-clean and Gerbers are validated, but PCIe enumeration on this SoC is not yet confirmed.

    14 parts3

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS62086RLTR?

Yes. The symbol is Celestial_Power_Switchmode:TI TPS62086RLT and the footprint EasyEDA_Cloud:VSON-7_L2.0-W2.0-P0.5-TL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS62086RLTR?

VSON-7(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TPS62086RLTR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS62086RLTR?

JLCPCB lists it as part C2071344, with 111 in stock; the sellers' links on this page open their listings.

What can replace the TPS62086RLTR?

Parts like it in the library: the DL1509-3.3E1 by DOINGTER, the XL1509-3.3BS by GREENMICRO, the MS1509-3.3 by MSKSEMI and the LM2596T-3.3(HX) by HANSCHIP semiconductor. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS62086RLTR?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.