Skip to the content
123456789

TPS56528DDAR

Texas InstrumentsExtended

-40℃~+85℃@(TA) 1 10uA 4.5V~18V 5A 600mV~7V 650kHz Adjustable Buck Buck Built-in Yes SOIC-8-EP DC-DC Converters ROHS

Part id
ti/TPS56528DDAR
Category
DC DC Converters
Package
SOIC-8-EP
Pins
9
In stock
3,588 at JLCPCB (C138716)
Used on
3 open-source boards

Overview

The TPS56528DDAR is a DC DC Converter made by Texas Instruments in a SOIC-8-EP package with 9 pins. -40℃~+85℃@(TA) 1 10uA 4.5V~18V 5A 600mV~7V 650kHz Adjustable Buck Buck Built-in Yes SOIC-8-EP DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (Regulator_Switching:TPS56528DDA, from KiCad's library) and its footprint (Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 3,588 are in stock at JLCPCB (part C138716). 3 open-source boards in 2 repositories on GitHub use it.

Symbol

3VREG54PG1EN2VFB5GND6SW7VBST8VIN
Regulator_Switching:TPS56528DDAFrom KiCad's library

Footprint

123456789
Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

15
Supply, least
4.5 V · VIN, recommended operating min · p. 4
Supply, most
18 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
20 V · VIN, absolute maximum · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
85 °C · Operating free-air temperature max · p. 4
Junction, hottest
150 °C · Operating junction temperature max · p. 4
Takes working
170 µA · VIN non-switching supply current typical, EN = 5 V, V(FB) = 0.7 V, TA = 25°C · p. 5
Takes asleep
3.8 µA · VIN shutdown current typical, EN = 0 V, TA = 25°C · p. 5
Gives
5 A · Rated converter output current max · p. 12
Current limit
6.2 A · Valley current limit typical, LOUT = 1.5 uH · p. 5
Feedback reference
600 mV · V(FB) threshold typical, continuous mode, TA = 25°C · p. 5
Switches at
650 kHz · Pseudo-constant switching frequency typical · p. 10
Junction to air (DDA (SO PowerPAD))
44.4 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to board (DDA (SO PowerPAD))
27.8 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (DDA (SO PowerPAD))
51.6 K/W · Junction-to-case top thermal resistance · p. 5

What it is and has

10
Control mode
D-CAP2™ · p. 1
Input voltage range
4.5 V to 18 V · p. 1
Output voltage range
0.6 V to 7 V · p. 1
Integrated FET resistance
68 mΩ high-side, 37 mΩ low-side · p. 1
Soft start
Prebiased soft start · p. 1
Switching frequency
650 kHz · p. 1
Protection
Cycle-by-cycle overcurrent limit · p. 1
Power good
Power good output · p. 1
Soft-start time
Fixed 1 ms · p. 1
Package
8-pin SO PowerPAD, 4.89 mm × 3.90 mm · p. 1

Around it

5
cap 0.1 µF
between VBST and SW; Required ceramic bootstrap capacitor. · p. 14
cap 0.47 µF
between VREG5 and GND; Required ceramic capacitor. · p. 14
cap over 10 μF
between VIN and GND; Recommended ceramic input decoupling capacitor; bulk capacitance depends on application; voltage rating must exceed maximum input voltage. · p. 14
cap 0.1 µF
between VIN and GND; Optional C3 from pin 8 to ground for additional high-frequency filtering. · p. 14
cap 2 × 22 µF
between VOUT and GND; Application example uses two TDK C3216X5R0J226M output capacitors, typical ESR 2 mΩ each. · p. 14

Specifications

54
ParameterConditionsAs printedPage
Input voltageVIN and ENmin -0.3 · max 20 V4
Input voltageVBSTmin -0.3 · max 26 V4
Input voltageVBST (10-ns-transient)min -0.3 · max 28 V4
Input voltageVBST (vs SW)min -0.3 · max 6.5 V4
Input voltageVFB and PGmin -0.3 · max 6.5 V4
Input voltageSWmin -2 · max 20 V4
Input voltageSW (10-ns-transient)min -3 · max 22 V4
Output voltageVREG5min -0.3 · max 6.5 V4
Output voltageGNDmin -0.3 · max 0.3 V4
Voltage from GND to thermal pad Vdiffmin -0.2 · max 0.2 V4
Operating junction temperature TJmin -40 · max 150 °C4
Storage temperature Tstgmin -55 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±500 Vmax 500 V4
Supply input voltage VINmin 4.5 · max 18 V4
Input voltage VIVBSTmin -0.1 · max 24 V4
Input voltage VIVBST (10-ns-transient)min -0.1 · max 27 V4
Input voltage VIVBST(vs SW)min -0.1 · max 6 V4
Input voltage VIPGmin -0.1 · max 5.7 V4
Input voltage VIENmin -0.1 · max 18 V4
Input voltage VIVFBmin -0.1 · max 5.5 V4
Input voltage VISWmin -1.8 · max 18 V4
Input voltage VISW (10-ns-transient)min -3 · max 21 V4
Input voltage VIGNDmin -0.1 · max 0.1 V4
Output voltage (VREG5) VOmin -0.1 · max 5.7 V4
Output current (IVREG5) IOmin 0 · max 5 mA4
Operating free-air temperature TAmin -40 · max 85 °C4
Operating junction temperature TJmin -40 · max 150 °C4
Junction-to-ambient thermal resistance RθJADDA (SO PowerPAD), 8 PINStyp 44.4 °C/W5
Junction-to-case (top) thermal resistance RθJCtopDDA (SO PowerPAD), 8 PINStyp 51.6 °C/W5
Junction-to-board thermal resistance RθJBDDA (SO PowerPAD), 8 PINStyp 27.8 °C/W5
Junction-to-top characterization parameter ψJTDDA (SO PowerPAD), 8 PINStyp 8.7 °C/W5
Junction-to-board characterization parameter ψJBDDA (SO PowerPAD), 8 PINStyp 27.7 °C/W5
Junction-to-case (bottom) thermal resistance RθJCbotDDA (SO PowerPAD), 8 PINStyp 5.3 °C/W5
Operating non-switching supply current I(VIN)VIN = 12 V; VIN current, TA = 25°C, EN = 5 V, V(FB) = 0.7 Vtyp 170 · max 350 uA5
Shutdown supply current I(VINSDN)VIN = 12 V; VIN current, TA = 25°C, EN = 0 Vtyp 3.8 · max 10 uA5
EN high-level input voltage V(EN)VIN = 12 V; ENmin 1.6 V5
EN low-level input voltage V(EN)VIN = 12 V; ENmax 0.6 V5
EN pin resistance to GND R(EN)VIN = 12 V; VEN = 12 Vmin 180 · typ 350 · max 700 kΩ5
V(FB) threshold voltage V(FBTH)VIN = 12 V; TA = 25°C, VO = 1.05 V, IO = 10 mA, advanced Eco-Mode operationtyp 606 mV5
V(FB) threshold voltage V(FBTH)VIN = 12 V; TA = 25°C, VO = 1.05 V, continuous mode operationmin 593 · typ 600 · max 607 mV5
V(FB) threshold voltage V(FBTH)VIN = 12 V; TA = -40 to 85°C, VO = 1.05 V, continuous mode operation; not production testedmin 588 · typ 600 · max 612 mV5
V(FB) input current I(VFB)VIN = 12 V; V(FB) = 0.7 V, TA = 25°C; maximum magnitude ±0.15 uAtyp 0 · max 0.15 uA5
SW discharge current I(DISCHG)VIN = 12 V; EN = 0 V, SW = 1 V, TA = 25°Cmin 1 · typ 1.5 mA5
VREG5 output voltage V(VREG5)TA = 25°C, 6.0 V < VIN < 18 V, 0 < I(VREG5) < 5 mAmin 5.2 · typ 5.5 · max 5.7 V5
Output current I(VREG5)VIN = 6 V, V(REG5) = 4 V, TA = 25°Cmin 20 mA5
High-side switch resistance RDS(on)VIN = 12 V; 25°C, V(BST) - SW = 5.5 Vtyp 68 mΩ5
Low-side switch resistance RDS(on)VIN = 12 V; 25°Ctyp 37 mΩ5
Current limit I(ocl)VIN = 12 V; LOUT = 1.5 uH; not production testedmin 5.5 · typ 6.2 · max 7.8 A5
Thermal shutdown threshold T(SDN)Shutdown temperature; not production testedtyp 165 °C5
Thermal shutdown threshold T(SDN)Hysteresis; not production testedtyp 35 °C5
PG threshold V(THPG)VIN = 12 V; VFB rising (good)min 85 · typ 90 · max 95 %5
PG threshold V(THPG)VIN = 12 V; VFB falling (Fault)typ 85 %5
PG sink current IPGVIN = 12 V; PG = 0.5 Vmin 2 · typ 4 mA5

Pins, by the datasheet

9
1 EN
Active-high enable input; must be pulled up to enable the device. · p. 3
2 VFB
Converter feedback input; connect to output voltage with a feedback resistor divider. · p. 3
3 VREG5
5.5-V supply output; connect a capacitor to GND; inactive when EN is low. · p. 3
4 PG
Open-drain power good output. · p. 3
5 GND
Power ground return for switching circuit; connect sensitive SS and VFB returns to GND at a single point. · p. 3
6 SW
Switch node between the high-side and low-side NFETs. · p. 3
7 VBST
High-side FET gate-drive supply; connect 0.1-uF capacitor to SW; internal diode connects VREG5 to VBST. · p. 3
8 VIN
Input voltage supply pin. · p. 3
— PowerPAD
Thermal pad; must be soldered for appropriate dissipation and connected to GND. · p. 3

Open-source boards using it

3
  • 8 layers167.2 × 95.4 mmRASBB, the printed circuit board in 3D

    RASBB

    Tobias-DG3YEV/RA-Sentinel

    FPGA based WiFi Intrusion detection system

    714 parts41GPL-3.0
  • 8 layers167.2 × 95.4 mmRASBB, the printed circuit board in 3D

    RASBB

    Tobias-DG3YEV/RA-Sentinel

    FPGA based WiFi Intrusion detection system

    639 parts41GPL-3.0

Questions

Is there a KiCad symbol and footprint for the TPS56528DDAR?

Yes. The symbol is Regulator_Switching:TPS56528DDA and the footprint Package_SO:Texas_HSOP-8-1EP_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS56528DDAR?

SOIC-8-EP, with 9 pins. Its footprint is drawn on this page.

Where is the TPS56528DDAR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS56528DDAR?

JLCPCB lists it as part C138716, with 3,588 in stock; the sellers' links on this page open their listings.

Which open-source boards use the TPS56528DDAR?

3 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.