Skip to the content
9

TPS55289RYQR

Texas InstrumentsExtended

-40℃~+125℃@(TJ) 1 200kHz~2.2MHz 3V~30V 800mV~22V 860uA 8A Adjustable Buck-Boost Buck-Boost Built-in Light load efficient mode、Adjustable soft-start、Cycle-by-cycle current limiting、Adjustable current limiting、Frequency synchronization、Hiccup current limiting、Dynamic voltage scaling、Built-in LDO regulator、EMI optimization (spread spectrum)、Cable compensation Yes VQFN-HR-21(3x5) DC-DC Converters ROHS

Part id
ti/TPS55289RYQR
Category
DC DC Converters
Package
VQFN-HR-21(3x5)
Pins
21
In stock
3,515 at JLCPCB (C5942077)
Used on
6 open-source boards

Overview

The TPS55289RYQR is a DC DC Converter made by Texas Instruments in a VQFN-HR-21(3x5) package with 21 pins. -40℃~+125℃@(TJ) 1 200kHz~2.2MHz 3V~30V 800mV~22V 860uA 8A Adjustable Buck-Boost Buck-Boost Built-in Light load efficient mode、Adjustable soft-start、Cycle-by-cycle current limiting、Adjustable current limiting、Frequency synchronization、Hiccup current limiting、Dynamic voltage scaling、Built-in LDO regulator、EMI optimization (spread spectrum)、Cable compensation Yes VQFN-HR-21(3x5) DC-DC Converters ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS55289QWRYQRQ1, from EasyEDA) and its footprint (EasyEDA_Cloud:VQFN-21_L5.0-W3.0-P0.50-TL, from EasyEDA), ready for a KiCad board. 3,515 are in stock at JLCPCB (part C5942077). 6 open-source boards in 6 repositories on GitHub use it.

Symbol

20BOOT119BOOT216CDC15COMP14FB/INT#6FSW13ISN12ISP3SCL4SDA8SW110SW29PGND17AGND11VOUT2MODE1EN/UVLO5DITH/SYNC7VIN18VCC21EXTVCC
EasyEDA_Cloud:TPS55289QWRYQRQ1From EasyEDA

Footprint

9
EasyEDA_Cloud:VQFN-21_L5.0-W3.0-P0.50-TLFrom EasyEDA

From the datasheet

17
Supply, least
3 V · VIN, recommended operating minimum · p. 5
Supply, most
30 V · VIN, recommended operating maximum · p. 5
Supply, absolute maximum
35 V · VIN, absolute maximum · p. 5
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 5
Takes working
1.52 mA · sum of VIN and VOUT typical quiescent currents, enabled without switching · p. 6
Takes asleep
800 nA · VIN shutdown current, typical, VIN = 3.0 V to 14 V · p. 6
Feedback reference
1.129 V · FB/INT reference, typical, external feedback with REF=0780H · p. 7
Feedback reference
846 mV · FB/INT reference, typical, external feedback with REF=058CH · p. 7
Feedback reference
508 mV · FB/INT reference, typical, external feedback with REF=0334H · p. 7
Feedback reference
282 mV · FB/INT reference, typical, external feedback with REF=01A4H · p. 7
Switches at
200 kHz · Switching frequency, typical, RFSW = 100 k · p. 7
Switches at
2.2 MHz · Switching frequency, typical, RFSW = 8.4 k · p. 7
Current limit
8 A · Average inductor current limit, typical, FPWM, VIN = 8 V, VOUT = 20 V, 400 kHz · p. 7
Junction to air (RYQ (VQFN))
43.4 K/W · Junction-to-ambient, Standard · p. 6
Junction to air (RYQ (VQFN))
27.5 K/W · Junction-to-ambient, EVM · p. 6
Junction to case (RYQ (VQFN))
22.3 K/W · Junction-to-case top, Standard · p. 6
Junction to board (RYQ (VQFN))
7.4 K/W · Junction-to-board, Standard · p. 6

What it is and has

13
Input voltage range
3.0 V to 30 V · p. 1
Reference voltage accuracy
±1% · p. 1
Output current monitoring accuracy
±5% · p. 1
Interface
I2C · p. 1
Light-load modes
Programmable PFM and FPWM · p. 1
Clock synchronization
Optional · p. 1
Spread spectrum
Optional programmable · p. 1
Protection
Output overvoltage protection · p. 1
Protection
Hiccup mode for output short-circuit protection · p. 1
Protection
Thermal shutdown · p. 1
Average inductor current limit
8 A · p. 1
Package
3.0-mm × 5.0-mm HotRod QFN · p. 1
Programmable output voltage
0.8 V to 22 V, 10-mV steps · p. 1

Around it

11
cap more than 4.7 μF
between VCC and AGND; Required ceramic capacitor. · p. 4
cap 0.1 µF
between BOOT2 and SW2; Required ceramic bootstrap capacitor. · p. 4
cap 0.1 µF
between BOOT1 and SW1; Required ceramic bootstrap capacitor. · p. 4
ind 4.7 µH
between SW1 and SW2; Nominal effective inductance; recommended range 1 uH to 10 uH. · p. 5
cap 22 µF
between VIN and PGND; Nominal effective input capacitance; minimum 4.7 uF. · p. 5
cap 100 µF
between VOUT and PGND; Nominal effective output capacitance; recommended range 10 uF to 1000 uF. · p. 5
res 49.9 kΩ
between FSW and GND; 1% resistor selected for the application's 400-kHz switching frequency. · p. 34
ind 4.7 µH
between SW1 and SW2; Application example inductor; selected part is Coilcraft XAL7070-472. · p. 35
cap 20 µF
between VIN and GND; Total effective input capacitance starting point for this application; ceramic capacitors recommended. · p. 36
cap 0.1 µF
between VIN and GND; 0402 ceramic capacitor placed close to VIN and GND to suppress high frequency noise. · p. 36
cap 0.1 μF
between VOUT and GND; 0402 ceramic capacitor placed close to VOUT and GND to suppress high frequency noise. · p. 37

Specifications

117
ParameterConditionsAs printedPage
Voltage range at pins (2)VIN, SW1min -0.3 · max 35 V5
Voltage range at pins (2)VCC, SCL, SDA, FSW, COMP, FB/INT, MODE, CDC, DITH/SYNC, EXTVCCmin -0.3 · max 6 V5
Voltage range at pins (2)VOUT, SW2, ISP, ISNmin -0.3 · max 25 V5
Voltage range at pins (2)EN/UVLOmin -0.3 · max 20 V5
Voltage range at pins (2)SCL, SDA, FSW, COMP, FB/INT, MODE, CDC, DITH/SYNC, EXTVCC; maximum VCC + 0.3 Vmin -0.3 V5
Junction temperature, TJ (3) TJmin -40 · max 150 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1); ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002(2); ±500 Vmax 500 V5
Input voltage range VINmin 3 · max 30 V5
Output voltage range VOUTmin 0.8 · max 22 V5
Effective inductance range LNOM column represented as typmin 1 · typ 4.7 · max 10 uH5
Effective input capacitance range CINNOM column represented as typmin 4.7 · typ 22 uF5
Effective output capacitance range COUTNOM column represented as typmin 10 · typ 100 · max 1000 uF5
Operating junction temperature TJmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RθJARYQ (VQFN), 26 PINS, Standardtyp 43.4 °C/W6
Junction-to-ambient thermal resistance RθJARYQ (VQFN), 26 PINS, EVM (2)typ 27.5 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)RYQ (VQFN), 26 PINS, Standardtyp 22.3 °C/W6
Junction-to-board thermal resistance RθJBRYQ (VQFN), 26 PINS, Standardtyp 7.4 °C/W6
Junction-to-top characterization parameter ΨJTRYQ (VQFN), 26 PINS, Standardtyp 0.7 °C/W6
Junction-to-top characterization parameter ΨJTRYQ (VQFN), 26 PINS, EVM (2)typ 0.7 °C/W6
Junction-to-board characterization parameter YJBRYQ (VQFN), 26 PINS, Standardtyp 7.2 °C/W6
Junction-to-board characterization parameter YJBRYQ (VQFN), 26 PINS, EVM (2)typ 11.1 °C/W6
Under voltage lockout threshold VVIN_UVLOVIN risingmin 2.8 · typ 2.9 · max 3 V6
Under voltage lockout threshold VVIN_UVLOVIN fallingmin 2.6 · typ 2.65 · max 2.7 V6
Quiescent current into VIN pin IQIC enabled, no load, no switching. VIN = 3.0 V to 24 V, VOUT = 0.8 V, VFB = VREF + 0.1 V, RFSW = 100 kΩ, TJ up to 125°Ctyp 760 · max 860 uA6
Quiescent current into VOUT pin IQIC enabled, no load, no switching, VIN = 3.0 V, VOUT = 3 V to 20 V, VFB = VREF + 0.1 V, RFSW = 100 kΩ, TJ up to 125°Ctyp 760 · max 860 uA6
Shutdown current into VIN pin ISDIC disabled, VIN = 3.0 V to 14 V, TJ up to 125°Ctyp 0.8 · max 3 uA6
Internal regulator output VCCIVCC = 50 mA, VIN = 8 V, VOUT = 20 Vmin 5 · typ 5.2 · max 5.4 V6
EN logic high threshold VEN_HVCC = 3.0 V to 5.5 Vmax 1.15 V6
EN logic low threshold VEN_LVCC = 3.0 V to 5.5 Vmin 0.4 V6
Enable threshold hysteresis VEN_HYSVCC = 3.0 V to 5.5 Vmin 0.04 V6
UVLO rising threshold at the EN/UVLO pin VUVLOVCC = 3.0 V to 5.5 Vmin 1.2 · typ 1.23 · max 1.26 V6
UVLO threshold hysteresis VUVLO_HYSVCC = 3.0 V to 5.5 Vtyp 10 mV6
Sourcing current at the EN/UVLO pin IUVLOVEN/UVLO = 1.3 Vmin 4.5 · typ 5 · max 5.5 uA6
Output overvoltage protection threshold VOVPmin 22.5 · typ 23.5 · max 24.5 V6
Overvoltage protection hysteresis VOVP_HYStyp 1 V6
Leakage current at FB pin IFB_LKGTj up to 125°Cmax 100 nA6
Leakage current into VOUT pin IVOUT_LKGIC disabled, VOUT = 20 V, VSW2 = 0 V, TJ up to 125°Ctyp 1 · max 20 uA6
Output discharge current IDISCHGVOUT = 20 V, VCC = 5.2 Vmin 40 · typ 100 · max 170 mA6
Resolution of reference voltage DACtyp 11 bits6
Output voltage when VREF is set to 1.129 V VOUT_FULLVOUT_FS=03h, REF=0780h, VREF = 1.129 Vmin 19.7 · typ 20 · max 20.3 V7
Output voltage when VREF is set to 1.129 V VOUT_FULLVOUT_FS=02h, REF=0780h, VREF = 1.129 Vmin 14.78 · typ 15 · max 15.22 V7
Output voltage when VREF is set to 1.129 V VOUT_FULLVOUT_FS=01h, REF=0780h, VREF = 1.129 Vmin 9.85 · typ 10 · max 10.15 V7
Output voltage when VREF is set to 1.129 V VOUT_FULLVOUT_FS=00h, REF=0780h, VREF = 1.129 Vmin 4.93 · typ 5 · max 5.07 V7
Output voltage when VREF is set to 45 mV VOUT_ZEROVOUT_FS=03h, REF=0000h, VREF = 45 mVmin 0.74 · typ 0.8 · max 0.86 V7
Output voltage when VREF is set to 45 mV VOUT_ZEROVOUT_FS=02h, REF=0000h, VREF = 45 mVmin 0.55 · typ 0.6 · max 0.65 V7
Output voltage when VREF is set to 45 mV VOUT_ZEROVOUT_FS=01h, REF=0000h, VREF = 45 mVmin 0.36 · typ 0.4 · max 0.44 V7
Output voltage when VREF is set to 45 mV VOUT_ZEROVOUT_FS=00h, REF=0000h, VREF = 45 mVmin 0.18 · typ 0.2 · max 0.22 V7
Reference voltage at the FB/INT pin when using external feedback VREFExternal feedback with REF=0780Hmin 1.117 · typ 1.129 · max 1.141 V7
Reference voltage at the FB/INT pin when using external feedback VREFExternal feedback with REF=058CHmin 0.837 · typ 0.846 · max 0.855 V7
Reference voltage at the FB/INT pin when using external feedback VREFExternal feedback with REF=0334Hmin 0.502 · typ 0.508 · max 0.514 V7
Reference voltage at the FB/INT pin when using external feedback VREFExternal feedback with REF=01A4Hmin 0.276 · typ 0.282 · max 0.288 V7
Low-side MOSFET on resistance on buck side RDS(on)VOUT = 20 V, VCC = 5.2 Vtyp 22 mΩ7
High-side MOSFET on resistance on buck side RDS(on)VOUT = 20 V, VCC = 5.2 Vtyp 14 mΩ7
Low-side MOSFET on resistance on boost side RDS(on)VOUT = 20 V, VCC = 5.2 Vtyp 11 mΩ7
High-side MOSFET on resistance on boost side RDS(on)VOUT = 20 V, VCC = 5.2 Vtyp 11 mΩ7
Switching frequency fSWRFSW = 100 kmin 180 · typ 200 · max 220 kHz7
Switching frequency fSWRFSW = 8.4 kmin 2000 · typ 2200 · max 2400 kHz7
Minimum off time tOFF_minBoost modetyp 90 · max 145 ns7
Minimum on time tON_minBuck modetyp 90 · max 130 ns7
Voltage at the FSW pin VSWtyp 1 V7
Average inductor current limit ILIM_AVGVIN = 8 V, VOUT = 20 V, fSW = 400 kHz, FPWMmin 6.7 · typ 8 A7
Average inductor current limit ILIM_AVGVIN = 8 V, VOUT = 20 V, fSW = 400 kHz, PFMmin 6.7 · typ 8 A7
Peak inductor current limit at boost high side ILIM_PKVIN = 8 V, VOUT = 20 V, fSW = 400 kHz, FPWMtyp 13 A7
Peak inductor current limit at boost high side ILIM_PKVIN = 8 V, VOUT = 20 V, fSW = 400 kHz, PFMtyp 13 A7
Current loop regulation voltage between ISP and ISN pin VSNSVISN = 2 V to 21 V, IOUT_LIMIT register = 10111100bmin 28.5 · typ 30 · max 31.5 mV7
Current loop regulation voltage between ISP and ISN pin VSNSVISN = 2 V to 21 V, IOUT_LIMIT register = 11100100bmin 48 · typ 50 · max 52 mV7
Voltage at the CDC pin VCDCRCDC = 20 kΩ or floating, VISP – VISN = 50 mVmin 0.93 · typ 1 · max 1.05 V8
Voltage at the CDC pin VCDCRCDC = 20 kΩ or floating, VISP – VISN = 2 mVtyp 40 · max 75 mV8
VOUT increase for cable drop compensation VOUT_CDCInternal output feedback, CDC[2:0]=111, VISP – VISN = 50 mVmin 650 · typ 700 · max 750 mV8
VOUT increase for cable drop compensation VOUT_CDCInternal output feedback, CDC[2:0]=111, VISP – VISN = 2 mVtyp 30 · max 60 mV8
VOUT increase for cable drop compensation VOUT_CDCInternal output feedback, CDC[2:0]=001, VISP – VISN = 50 mVmin 70 · typ 100 · max 130 mV8
VOUT increase for cable drop compensation VOUT_CDCInternal output feedback, CDC[2:0]=001, VISP – VISN = 10 mVtyp 20 · max 40 mV8
FB/INT pin sinking current IFB_CDCExternal output feedback, RCDC = 20 kΩ, VISP – VISN = 50 mVmin 7.23 · typ 7.5 · max 7.87 uA8
FB/INT pin sinking current IFB_CDCExternal output feedback, RCDC = 20 kΩ, VISP – VISN = 0 mVtyp 0 · max 0.3 uA8
FB/INT pin sinking current IFB_CDCExternal output feedback, RCDC = floating, VISP – VISN = 50 mVtyp 0 · max 0.3 uA8
COMP pin sink current ISINKVFB = VREF + 400 mV, VCOMP = 1.1 V, VCC = 5 Vtyp 20 uA8
COMP pin source current ISOURCEVFB = VREF – 400 mV, VCOMP = 1.1 V, VCC = 5 Vtyp 60 uA8
High clamp voltage at the COMP pin VCCLPHtyp 1.2 V8
Low clamp voltage at the COMP pin VCCLPLtyp 0.7 V8
Error amplifier transconductance GEAtyp 190 uA/V8
Soft-start time tSSmin 2.5 · typ 3.6 · max 5 ms8
Dithering charge current IDITH_CHGVDITH/SYNC = 1.0 V; RFSW = 49.9 kΩ; voltage rising from 0.9 Vtyp 2 uA8
Dithering discharge current IDITH_DISVDITH/SYNC = 1.0 V; RFSW = 49.9 kΩ; voltage falling from 1.1 Vtyp 2 uA8
Dither high threshold VDITH_Htyp 1.07 V8
Dither low threshold VDITH_Ltyp 0.93 V8
Sync clock high voltage threshold VSNYC_Hmax 1.2 V8
Sync clock low voltage threshold VSYNC_Lmin 0.4 V8
Minimum sync clock pulse width tSYNC_MINmin 50 ns8
Hiccup off time tHICCUPtyp 76 ms8
MODE logic high threshold VMODE_HVCC = 3.0 V to 5.5 Vmax 1.2 V8
MODE logic low threshold VMODE_LVCC = 3.0 V to 5.5 Vmin 0.4 V8
EXTVCC logic high threshold VEXTVCC_HVCC = 3.0 V to 5.5 Vmax 1.2 V8
EXTVCC logic low threshold VEXTVCC_LVCC = 3.0 V to 5.5 Vmin 0.4 V8
IO voltage range for I2C VI2C_IOmin 1.7 · max 5.5 V9
I2C input high threshold VI2C_HVCC = 3.0 V to 5.5 Vmax 1.2 V9
I2C input low threshold VI2C_LVCC = 3.0 V to 5.5 Vmin 0.4 V9
Leakage current into FB/INT pin when outputting high impedance IFB/INT_HVFB/INT = 5 Vmax 100 nA9
Output low voltage range of the FB/INT pin VFB/INT_LSinking 4-mA currenttyp 0.03 · max 0.1 V9
Thermal shutdown threshold TSDTJ risingtyp 175 °C9
Thermal shutdown hysteresis TSD_HYSTJ falling below TSDtyp 20 °C9
SCL clock frequency fSCLmin 100 · max 1000 kHz9
Bus free time between a STOP and START condition tBUFFast mode plusmin 0.5 us9
Hold time (repeated) START condition tHD(STA)min 260 ns9
Low period of the SCL clock tLOWmin 0.5 us9
High period of the SCL clock tHIGHmin 260 ns9
Setup time for a repeated START condition tSU(STA)min 260 ns9
Data setup time tSU(DAT)min 50 ns9
Data hold time tHD(DAT)min 0 us9
Rise time of SCL signal tRCLmax 120 ns9
Rise time of SCL signal after a repeated START condition and after an ACK bit tRCL1max 120 ns9
Fall time of SCL signal tFCLmax 120 ns9
Rise time of SDA signal tRDAmax 120 ns9
Fall time of SDA signal tFDAmax 120 ns9
Setup time of STOP condition tSU(STO)min 260 ns9
Capacitive load for SDA and SCL CBmax 200 pF9

Pins, by the datasheet

21
1 EN/UVLO
Enable and programmable input undervoltage lockout; high enables and low shuts down, with a 1.23-V UVLO reference above the enable threshold. · p. 3
2 MODE
I2C target address selection: high selects 74H, low selects 75H. · p. 3
3 SCL
Clock of I2C interface. · p. 3
4 SDA
Data of I2C interface. · p. 3
5 DITH/SYNC
Capacitor to ground sets dithering frequency; grounding or pulling above 1.2 V disables dithering, and an external clock synchronizes switching. · p. 3
6 FSW
Resistor to AGND programs switching frequency. · p. 3
7 VIN
Input of the buck-boost converter. · p. 3
8 SW1
Buck switching node connecting the internal low-side MOSFET drain and high-side MOSFET source. · p. 3
9 PGND
Power ground of the IC. · p. 3
10 SW2
Boost switching node connecting the internal low-side MOSFET drain and high-side MOSFET source. · p. 3
11 VOUT
Output of the buck-boost converter. · p. 3
12 ISP
Positive current-sense input; optional resistor to ISN sets output current sensing, or connect ISP and ISN to VOUT to disable output current limiting. · p. 3
13 ISN
Negative current-sense input; optional resistor to ISP sets output current sensing, or connect ISP and ISN to VOUT to disable output current limiting. · p. 4
14 FB/INT
External feedback divider input, or active-low fault indicator output when internal feedback is selected. · p. 4
15 COMP
Internal error amplifier output; connect compensation network to AGND. · p. 4
16 CDC
Output proportional to ISP–ISN sense voltage; resistor to AGND sets cable voltage droop compensation. · p. 4
17 AGND
Signal ground of the IC. · p. 4
18 VCC
Internal regulator output; requires a ceramic capacitor greater than 4.7 uF to AGND. · p. 4
19 BOOT2
Boost high-side MOSFET gate-driver supply; connect a 0.1-uF ceramic capacitor to SW2. · p. 4
20 BOOT1
Buck high-side MOSFET gate-driver supply; connect a 0.1-uF ceramic capacitor to SW1. · p. 4
21 EXTVCC
High selects internal LDO for VCC; low selects external 5 V for VCC. · p. 4

Ordering codes, by the datasheet

1
TPS55289RYQR
VQFN-HR · 21 pins, RYQ package drawing, package quantity 3000, operating temperature -40 to 125 °C. · p. 47

Open-source boards using it

6
  • 4 layers102.2 × 74.4 mmController pcb, the printed circuit board in 3D

    Controller pcb

    chevalierid/alan-setup

    Materials for experimental setup examining the effects of artificial light at night on insects

    62 parts2
  • 2 layers101.5 × 47.3 mmBRM, the printed circuit board in 3D

    BRM

    BHopper9970/BRM

    A power distribution and voltage regulator PCB designed for FRC robots

    48 partsGPL-3.0
  • 4 layers25 × 25 mm12VBuckBoost, the printed circuit board in 3D

    12VBuckBoost

    Fortinbra/12VI2CBuckBoost

    A 12V input, variable output, programmable BuckBoost Converter

    18 partsMIT
  • 4 layers58 × 58 mmElec, the printed circuit board in 3D

    Elec

    Ng-Chen-Xuan/USB-C-Portable-PSU

    USB-C PD powered variable power supply

    157 parts
  • 2 layers182 × 126.2 mmFinal FullPCB, the printed circuit board in 3D

    Final FullPCB

    segf4u1t-139/EDL_Project_2026

    A Hard fork of the EDL Project 2026 in IIT Bombay

    244 parts
  • 2 layers60 × 100 mmWrectangle V4-old, the printed circuit board in 3D

    Wrectangle V4-old

    Wildcat-Rocket-Engineering-Club/WRECtangle

    WRECtangle code

    135 parts

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the TPS55289RYQR?

Yes. The symbol is EasyEDA_Cloud:TPS55289QWRYQRQ1 and the footprint EasyEDA_Cloud:VQFN-21_L5.0-W3.0-P0.50-TL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS55289RYQR?

VQFN-HR-21(3x5), with 21 pins. Its footprint is drawn on this page.

Where is the TPS55289RYQR datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS55289RYQR?

JLCPCB lists it as part C5942077, with 3,515 in stock; the sellers' links on this page open their listings.

What can replace the TPS55289RYQR?

Parts like it in the library: the TPS55289QWRYQRQ1 by Texas Instruments and the TPS551892QWRYQRQ1 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS55289RYQR?

6 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.