TPS54160ADGQ
Texas InstrumentsExtended
-40℃~+150℃@(TJ) 1 1.5A 116uA 2.5MHz 3.5V~60V 800mV~58V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHS
- Part id
- ti/TPS54160ADGQ
- Category
- DC DC Converters
- Package
- MSOP-10-EP
- Pins
- 11
- In stock
- 598 at JLCPCB (C390949)
Overview
The TPS54160ADGQ is a DC DC Converter made by Texas Instruments in a MSOP-10-EP package with 11 pins. -40℃~+150℃@(TJ) 1 1.5A 116uA 2.5MHz 3.5V~60V 800mV~58V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (Celestial_Power_Switchmode:TI TPS54160ADGQ, from Altium's library) and its footprint (EasyEDA_Cloud:MSOP-10_L3.0-W3.0-P0.50-LS4.9-BL-EP-1, from EasyEDA), ready for a KiCad board. 598 are in stock at JLCPCB (part C390949).
Symbol
Footprint
From the datasheet
13- Supply, least
- 3.5 V · VIN, recommended operating min · p. 6
- Supply, most
- 60 V · VIN, recommended operating max · p. 6
- Supply, absolute maximum
- 65 V · VIN, absolute maximum · p. 5
- Junction, hottest
- 150 °C · junction temperature max · p. 6
- Takes working
- 116 µA · VIN, typical nonswitching supply current, VSENSE = 0.83 V, VIN = 12 V, 25°C · p. 6
- Takes asleep
- 1.3 µA · VIN, typical shutdown current, EN = 0 V, 25°C · p. 6
- Gives
- 1.5 A · output current max · p. 6
- Current limit
- 2.7 A · typical current limit, VIN = 12 V, TJ = 25°C · p. 7
- Feedback reference
- 800 mV · typical voltage reference, TJ = 25°C · p. 6
- Switches at
- 581 kHz · typical switching frequency, RT = 200 kΩ · p. 7
- Junction to air (DGQ (10 PINS))
- 62.5 K/W · junction-to-ambient thermal resistance, standard board · p. 6
- Junction to board (DGQ (10 PINS))
- 28 K/W · junction-to-board thermal resistance · p. 6
- Junction to case (DGQ (10 PINS))
- 83 K/W · junction-to-case top thermal resistance · p. 6
What it is and has
7- High-side MOSFET
- 200 mΩ · p. 1
- Switching frequency
- 100 kHz to 2.5 MHz · p. 1
- External clock
- Synchronization · p. 1
- Slow start
- Adjustable, sequencing · p. 1
- Power good
- UV and OV output · p. 1
- Voltage reference
- 0.8 V internal · p. 1
- Light-load operation
- Pulse skipping Eco-mode · p. 1
Around it
11- ind 10μH
- between PH and VOUT; Example output filter inductor; MSS6132-103 selected. · p. 32
- cap 47 μF
- between VOUT and GND; Example output capacitor: 6.3 V X7R ceramic, 5 mΩ ESR. · p. 33
- diode B220A
- between PH and GND; Example Schottky catch diode; reverse voltage rating must cover maximum input voltage and peak current rating must exceed maximum inductor current. · p. 34
- cap at least 3 μF
- between VIN and GND; Required effective input decoupling capacitance after DC bias effects; X5R or X7R ceramic. Some applications also require bulk capacitance. · p. 34
- cap two 2.2 μF, 25 V
- between VIN and GND; Example input capacitors connected in parallel. · p. 35
- cap 3.3 nF
- between SS/TR and GND; Example slow-start capacitor for a 1 ms slow-start time. · p. 36
- cap 0.1-μF
- between BOOT and PH; Required ceramic bootstrap capacitor; X5R or better dielectric, rated 10 V or higher. · p. 36
- res 332kΩ
- between VIN and EN; Example UVLO divider upper resistor, paired with 61.9 kΩ to ground for 7.7 V start and 6.7 V stop. · p. 36
- res 61.9kΩ
- between EN and GND; Example UVLO divider lower resistor, paired with 332 kΩ from VIN. · p. 36
- res 10.0 kΩ
- between VSENSE and GND; Example feedback divider lower resistor R2. · p. 36
- res 31.6 kΩ
- between VOUT and VSENSE; Example feedback divider upper resistor R1; 1% standard value. · p. 36
Specifications
75| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input voltage | VIN | min -0.3 · max 65 V | 5 |
| Input voltage | EN; see note (2) | min -0.3 · max 5 V | 5 |
| Input voltage | BOOT | max 73 V | 5 |
| Input voltage | VSENSE | min -0.3 · max 3 V | 5 |
| Input voltage | COMP | min -0.3 · max 3 V | 5 |
| Input voltage | PWRGD | min -0.3 · max 6 V | 5 |
| Input voltage | SS/TR | min -0.3 · max 3 V | 5 |
| Input voltage | RT/CLK | min -0.3 · max 3.6 V | 5 |
| Input voltage | BOOT-PH | max 8 V | 5 |
| Output voltage | PH | min -0.6 · max 65 V | 5 |
| Output voltage | PH, 10-ns Transient | min -2 · max 65 V | 5 |
| Voltage Difference | PAD to GND; maximum magnitude ±200 mV | max 200 mV | 5 |
| Source current | EN | max 100 uA | 5 |
| Source current | BOOT | max 100 mA | 5 |
| Source current | VSENSE | max 10 uA | 5 |
| Source current | RT/CLK | max 100 uA | 5 |
| Sink current | COMP | max 100 uA | 5 |
| Sink current | PWRGD | max 10 mA | 5 |
| Sink current | SS/TR | max 200 uA | 5 |
| Operating junction temperature | min -40 · max 150 °C | 5 | |
| Storage temperature TSTG | min -65 · max 150 °C | 5 | |
| Human Body Model (HBM) ESD Stress Voltage QSS 009-105 (JESD22-A114A) VESD | TPS54160A | max 2 kV | 5 |
| Charged Device Model (CDM) ESD Stress Voltage QSS 009-147 (JESD22-C101B.01) VESD | max 500 V | 5 | |
| Supply input voltage range VIN | min 3.5 · max 60 V | 6 | |
| Output voltage range VO | min 0.8 · max 58 V | 6 | |
| Output current range IO | min 0 · max 1.5 A | 6 | |
| Junction Temperature TJ | min -40 · max 150 °C | 6 | |
| Junction-to-ambient thermal resistance (standard board) θJA | DGQ (10 PINS) | typ 62.5 °C/W | 6 |
| Junction-to-case (top) thermal resistance θJCtop | DGQ (10 PINS) | typ 83 °C/W | 6 |
| Junction-to-board thermal resistance θJB | DGQ (10 PINS) | typ 28 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | DGQ (10 PINS) | typ 1.7 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | DGQ (10 PINS) | typ 20.1 °C/W | 6 |
| Junction-to-case (bottom) thermal resistance θJCbot | DGQ (10 PINS) | typ 21 °C/W | 6 |
| Operating input voltage | TJ = –40°C to 150°C | min 3.5 · max 60 V | 6 |
| Internal undervoltage lockout threshold | No voltage hysteresis, rising and falling | typ 2.5 V | 6 |
| Shutdown supply current | EN = 0 V, 25°C, 3.5 V ≤ VIN ≤ 60 V | typ 1.3 · max 4 uA | 6 |
| Operating : nonswitching supply current | VSENSE = 0.83 V, VIN = 12 V, 25°C | typ 116 · max 136 uA | 6 |
| Enable threshold voltage | No voltage hysteresis, rising and falling (TPS54160A) | min 1.11 · typ 1.25 · max 1.36 V | 6 |
| Input current | Enable threshold +50 mV | typ -3.8 uA | 6 |
| Input current | Enable threshold –50 mV | typ -0.9 uA | 6 |
| Hysteresis current | min 1.91 · typ 2.95 · max 3.99 uA | 6 | |
| Voltage reference | TJ = 25°C | min 0.792 · typ 0.8 · max 0.808 V | 6 |
| Voltage reference | TJ = –40°C to 150°C | min 0.784 · typ 0.8 · max 0.816 V | 6 |
| On-resistance | VIN = 3.5 V, BOOT-PH = 3 V | typ 300 mΩ | 6 |
| On-resistance | VIN = 12 V, BOOT-PH = 6 V | typ 200 · max 410 mΩ | 6 |
| Input current | ERROR AMPLIFIER | typ 50 nA | 6 |
| Error amplifier transconductance (gM) | –2 uA < I(COMP) < 2 uA, V(COMP) = 1 V | typ 97 uMhos | 6 |
| Error amplifier transconductance (gM) during slow start | –2 uA < I(COMP) < 2 uA, V(COMP) = 1 V, VVSENSE = 0.4 V | typ 26 uMhos | 6 |
| Error amplifier dc gain | VVSENSE = 0.8 V | typ 10000 V/V | 6 |
| Error amplifier bandwidth | typ 2700 kHz | 6 | |
| Error amplifier source/sink | V(COMP) = 1 V, 100-mV overdrive; typical ±7 uA | typ 7 uA | 6 |
| COMP to switch current transconductance | typ 6 A/V | 6 | |
| Current limit threshold | VIN = 12 V, TJ = 25°C | min 1.8 · typ 2.7 A | 7 |
| Thermal shutdown | typ 182 °C | 7 | |
| Switching frequency range using RT mode | min 100 · max 2500 kHz | 7 | |
| Switching frequency fSW | RT = 200 kΩ | min 450 · typ 581 · max 720 kHz | 7 |
| Switching frequency range using CLK mode | min 300 · max 2200 kHz | 7 | |
| Minimum CLK input pulse width | typ 40 ns | 7 | |
| RT/CLK high threshold | typ 1.9 · max 2.2 V | 7 | |
| RT/CLK low threshold | min 0.5 · typ 0.7 V | 7 | |
| RT/CLK falling edge to PH rising edge delay | Measured at 500 kHz with RT resistor in series | typ 60 ns | 7 |
| PLL lock in time | Measured at 500 kHz | typ 100 us | 7 |
| Charge current | VSS/TR = 0.4 V | typ 2 uA | 7 |
| SS/TR-to-VSENSE matching | VSS/TR = 0.4 V | typ 45 mV | 7 |
| SS/TR-to-reference crossover | 98% nominal | typ 1 V | 7 |
| SS/TR discharge current (overload) | VSENSE = 0 V, V(SS/TR) = 0.4 V | typ 112 uA | 7 |
| SS/TR discharge voltage | VSENSE = 0 V | typ 54 mV | 7 |
| VSENSE threshold VVSENSE | VSENSE falling; lower threshold | typ 92 % | 7 |
| VSENSE threshold VVSENSE | VSENSE rising; lower threshold | typ 94 % | 7 |
| VSENSE threshold VVSENSE | VSENSE rising; upper threshold | typ 109 % | 7 |
| VSENSE threshold VVSENSE | VSENSE falling; upper threshold | typ 107 % | 7 |
| Hysteresis | VSENSE falling | typ 2 % | 7 |
| Output high leakage | VSENSE = VREF, V(PWRGD) = 5.5 V, 25°C | typ 10 nA | 7 |
| On resistance | I(PWRGD) = 3 mA, VSENSE < 0.79 V | typ 50 Ω | 7 |
| Minimum VIN for defined output | V(PWRGD) < 0.5 V, I(PWRGD) = 100 uA | typ 0.95 · max 1.5 V | 7 |
Pins, by the datasheet
11- 1 BOOT
- Connect a bootstrap capacitor between BOOT and PH; the output switches off if its voltage is too low until the capacitor is refreshed. · p. 4
- 2 VIN
- Input supply voltage, 3.5 V to 60 V. · p. 4
- 3 EN
- Enable with internal pull-up; pull below 1.2 V to disable or float to enable; two resistors adjust input undervoltage lockout. · p. 4
- 4 SS/TR
- Slow-start and tracking; an external capacitor sets output rise time, and this pin overrides the internal reference for tracking and sequencing. · p. 4
- 5 RT/CLK
- Connect a resistor to ground to set switching frequency or apply an external clock for PLL synchronization; returns to resistor operation if clock edges stop. · p. 4
- 6 PWRGD
- Asserts low for output voltage faults caused by thermal shutdown, dropout, over-voltage or EN shutdown. · p. 4
- 7 VSENSE
- Inverting node of the transconductance error amplifier. · p. 4
- 8 COMP
- Error amplifier output and output switch current comparator input; connect frequency compensation components here. · p. 4
- 9 GND
- Ground. · p. 4
- 10 PH
- Source of the internal high-side power MOSFET. · p. 4
- 11 Thermal Pad
- Electrically connect the exposed pad to GND on the printed circuit board for proper operation. · p. 4
Ordering codes, by the datasheet
1- TPS54160ADGQ
- MSOP (10) · TPS54160A tighter enable threshold; 3mm x 3mm body · p. 1
Parts like it
8TPS54160DGQ
MSOP-10-EP-40℃~+150℃@(TJ) 1 1.5A 116uA 2.5MHz 3.5V~60V 800mV~58V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS57140QDGQRQ1
MSOP-10-EP-40℃~+150℃@(TJ) 1 1.5A 116uA 2.5MHz 3.5V~42V 800mV~39V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersGBI1620MOAR
EMSOP-10-40℃~+125℃@(TJ) 1 100uA 2.5A 200kHz~2.5MHz 4.5V~60V Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting Step-down type EMSOP-10 DC-DC Converters ROHSGOSEMICONDC-DC ConvertersLT3481HMSE#PBF
MSOP-10-EP-40℃~+150℃@(TJ) 1 1.265V~20V 2A 3.6V~34V 300kHz~2.8MHz 50uA Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHSAnalog DevicesDC-DC ConvertersMIC4724YMME-TR
MSOP-10-40℃~+125℃@(TJ) 1 1V~5.5V 2MHz 3A 3V~6V 570uA Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Operating status indication、Built-in current sense resistor Step-down type MSOP-10 DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersLT3480MPMSE#PBF
MSOP-10-EP-55℃~+150℃@(TJ) 1 2.4MHz 2A 3.6V~36V 790mV~20V Adjustable Buck Buck Built-in MSOP-10-EP DC-DC Converters ROHSAnalog DevicesDC-DC ConvertersMIC4723YMME-TR
MSOP-10-EP-40℃~+125℃@(TJ) 1 1V~5.5V 2MHz 3A 3V~5.5V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersMIC4724YMME
MSOP-10-EP-40℃~+125℃@(TJ) 1 1V~5.5V 2MHz 3A 3V~6V Adjustable Buck Buck Built-in No MSOP-10-EP DC-DC Converters ROHSMicrochip TechnologyDC-DC Converters
Questions
Is there a KiCad symbol and footprint for the TPS54160ADGQ?
Yes. The symbol is Celestial_Power_Switchmode:TI TPS54160ADGQ and the footprint EasyEDA_Cloud:MSOP-10_L3.0-W3.0-P0.50-LS4.9-BL-EP-1, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS54160ADGQ?
MSOP-10-EP, with 11 pins. Its footprint is drawn on this page.
Where is the TPS54160ADGQ datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS54160ADGQ?
JLCPCB lists it as part C390949, with 598 in stock; the sellers' links on this page open their listings.
What can replace the TPS54160ADGQ?
Parts like it in the library: the TPS54160DGQ by Texas Instruments, the TPS57140QDGQRQ1 by Texas Instruments, the GBI1620MOAR by GOSEMICON and the LT3481HMSE#PBF by Analog Devices. Check their datasheets: a part that fits the footprint may still differ in its ratings.