Skip to the content
1234567

TPS2553DRV

Texas InstrumentsExtended

-40℃~+150℃ 1 1.5A 100mΩ 2.5V~6.5V Active High High Side Switch Overvoltage Protection、Soft-start、Under-voltage lockout、Reverse voltage protection、Integrated charge pump、Overcurrent Protection、Over temperature protection、Latch protection、Short-Circuit Protection、Reverse current blocking WSON-6-EP(2x2) Power Distribution Switches ROHS

Part id
ti/TPS2553DRV
Category
Power Distribution Switches
Package
WSON-6-EP(2x2)
Pins
6
In stock
26,988 at JLCPCB (C138719)

Overview

The TPS2553DRV is a power Distribution Switche made by Texas Instruments in a WSON-6-EP(2x2) package with 7 pins. -40℃~+150℃ 1 1.5A 100mΩ 2.5V~6.5V Active High High Side Switch Overvoltage Protection、Soft-start、Under-voltage lockout、Reverse voltage protection、Integrated charge pump、Overcurrent Protection、Over temperature protection、Latch protection、Short-Circuit Protection、Reverse current blocking WSON-6-EP(2x2) Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPS2550DRVR, from EasyEDA) and its footprint (EasyEDA_Cloud:WSON-6_L2.0-W2.0-P0.65-TL-EP, from EasyEDA), ready for a KiCad board. 26,988 are in stock at JLCPCB (part C138719).

Symbol

1OUT2ILIM3FAULT#4EN5GND6IN7EP
EasyEDA_Cloud:TPS2550DRVRFrom EasyEDA

Footprint

1234567
EasyEDA_Cloud:WSON-6_L2.0-W2.0-P0.65-TL-EPFrom EasyEDA

From the datasheet

16
Supply, least
2.5 V · IN, recommended operating min · p. 5
Supply, most
6.5 V · IN, recommended operating max · p. 5
Supply, absolute maximum
7 V · IN, absolute maximum · p. 5
Junction, hottest
150 °C · Junction temperature, absolute maximum · p. 5
Takes working
120 µA · IN, typical enabled current at VIN = 6.5V, no load, RILIM = 20kΩ · p. 7
Takes asleep
100 nA · IN, typical disabled current at VIN = 6.5V, no load · p. 7
Gives
1.5 A · OUT, continuous max at -40°C ≤ TJ ≤ 105°C · p. 5
Gives
1.2 A · OUT, continuous max at -40°C ≤ TJ ≤ 125°C · p. 5
Current limit
1.7 A · OUT, typical current limit with RILIM = 15kΩ, –40°C ≤ TJ ≤105°C · p. 7
Current limit
1.295 A · OUT, typical current limit with RILIM = 20kΩ, TJ = 25°C · p. 7
Current limit
520 mA · OUT, typical current limit with RILIM = 49.9kΩ, TJ = 25°C · p. 7
Current limit
130 mA · OUT, typical current limit with RILIM = 210kΩ · p. 7
Current limit
75 mA · OUT, typical current limit with ILIM shorted to IN · p. 7
Junction to air (DRV (WSON))
72 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to case (DRV (WSON))
85.3 K/W · Junction-to-case (top) thermal resistance · p. 6
Junction to board (DRV (WSON))
41.3 K/W · Junction-to-board thermal resistance · p. 6

What it is and has

7
Maximum load current
1.5A · p. 1
Current-limit accuracy
±6% at 1.7A (Typical) · p. 1
USB current limiting
Meets USB current-limiting requirements · p. 1
On-state resistance
100mΩ, DRV package · p. 1
Protection
Reverse input-output voltage protection · p. 1
Soft start
Built-in · p. 1
Overcurrent behavior
Constant-current mode · p. 14

Around it

2
cap 0.1µF or greater
between IN and GND; Ceramic; place as close to the IC as possible. · p. 4
res 15kΩ to 232kΩ, nominal 1%
between ILIM and GND; Sets the current-limit threshold. · p. 5

Specifications

61
ParameterConditionsAs printedPage
Voltage range on IN, OUT, EN or EN, ILIM, FAULTVoltages referenced to GNDmin -0.3 · max 7 V5
Voltage range from IN to OUTmin -7 · max 7 V5
Continuous FAULT sink currentmin 0 · max 25 mA5
ILIM source currentmin 0 · max 1 mA5
Maximum junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; rating ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101; rating ±500 Vmax 500 V5
Electrostatic discharge V(ESD)IEC 61000-4-2 contact discharge; rating ±8000 V; output terminals of EVMmax 8000 V5
Electrostatic discharge V(ESD)IEC 61000-4-2 air-gap discharge; rating ±15000 V; output terminals of EVMmax 15000 V5
Input voltage, IN VINmin 2.5 · max 6.5 V5
Enable voltage VENTPS2553/53-1min 0 · max 6.5 V5
High-level input voltage on EN or EN VIHmin 1.1 V5
Low-level input voltage on EN or EN VILmax 0.66 V5
Continuous output current, OUT IOUT-40°C ≤ TJ ≤ 125°Cmax 1.2 A5
Continuous output current, OUT IOUT-40°C ≤ TJ ≤ 105°Cmax 1.5 A5
Current-limit threshold resistor range (nominal 1%) from ILIM to GND RILIMmin 15 · max 232 kΩ5
Continuous FAULT sink current IOmin 0 · max 10 mA5
Input de-coupling capacitance, IN to GNDmin 0.1 uF5
Operating virtual junction temperature(1) TJIOUT ≤ 1.2Amin -40 · max 125 °C6
Operating virtual junction temperature(1) TJIOUT ≤ 1.5Amin -40 · max 105 °C6
Junction-to-ambient thermal resistance RθJATPS2553, DRV (WSON), 6 PINStyp 72 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)TPS2553, DRV (WSON), 6 PINStyp 85.3 °C/W6
Junction-to-board thermal resistance RθJBTPS2553, DRV (WSON), 6 PINStyp 41.3 °C/W6
Junction-to-top characterization parameter ψJTTPS2553, DRV (WSON), 6 PINStyp 1.7 °C/W6
Junction-to-board characterization parameter ψJBTPS2553, DRV (WSON), 6 PINStyp 41.7 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)TPS2553, DRV (WSON), 6 PINStyp 11.1 °C/W6
Static drain-source on-state resistance rDS(on)DRV package, TJ = 25°Ctyp 100 · max 115 mΩ6
Static drain-source on-state resistance rDS(on)DRV package, –40°C ≤ TJ ≤105°Cmax 140 mΩ6
Static drain-source on-state resistance rDS(on)DRV package, –40°C ≤ TJ ≤125°Cmax 150 mΩ6
Rise time, output trCL = 1uF, RL = 100Ω, VIN = 6.5V; see Figure 7-2typ 1.1 · max 1.5 ms6
Rise time, output trCL = 1uF, RL = 100Ω, VIN = 2.5V; see Figure 7-2typ 0.7 · max 1 ms6
Fall time, output tfCL = 1uF, RL = 100Ω, VIN = 6.5V; see Figure 7-2min 0.2 · max 0.5 ms6
Fall time, output tfCL = 1uF, RL = 100Ω, VIN = 2.5V; see Figure 7-2min 0.2 · max 0.5 ms6
Enable pin turn on/off thresholdmin 0.66 · max 1.1 V6
Input current IENVEN = 0V or 6.5V, VEN = 0V or 6.5Vmin -0.5 · max 0.5 uA6
Turnon time tonCL = 1uF, RL = 100Ω; see Figure 7-2max 3 ms6
Turnoff time toffCL = 1uF, RL = 100Ω; see Figure 7-2max 3 ms6
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 15kΩ, –40°C ≤ TJ ≤105°Cmin 1610 · typ 1700 · max 1800 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 20kΩ, TJ = 25°Cmin 1215 · typ 1295 · max 1375 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 20kΩ, –40°C ≤ TJ ≤ 125°Cmin 1200 · typ 1295 · max 1375 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 49.9kΩ, TJ = 25°Cmin 490 · typ 520 · max 550 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 49.9kΩ, –40°C ≤ TJ ≤ 125°Cmin 475 · typ 520 · max 565 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSRILIM = 210kΩmin 110 · typ 130 · max 150 mA7
Current-limit threshold (Maximum DC output current IOUT delivered to load) and Short-circuit current, OUT connected to GND IOSILIM shorted to INmin 50 · typ 75 · max 100 mA7
Response time to short circuit tIOSVIN = 5V; see Figure 7-3typ 2 us7
Reverse-voltage comparator trip point (VOUT – VIN)min 95 · typ 135 · max 190 mV7
Time from reverse-voltage condition to MOSFET turn offVIN = 5Vmin 3 · typ 5 · max 7 ms7
Supply current, low-level output IIN_offVIN = 6.5V, No load on OUT, VEN = 6.5V or VEN = 0Vtyp 0.1 · max 1 uA7
Supply current, high-level output IIN_onVIN = 6.5V, No load on OUT, RILIM = 20kΩtyp 120 · max 150 uA7
Supply current, high-level output IIN_onVIN = 6.5V, No load on OUT, RILIM = 210kΩtyp 100 · max 130 uA7
Reverse leakage current IREVVOUT = 6.5V, VIN = 0V, TJ = 25°Ctyp 0.01 · max 1 uA7
Low-level input voltage, IN UVLOVIN risingtyp 2.35 · max 2.45 V7
Hysteresis, INTJ = 25°Ctyp 25 mV7
Output low voltage, FAULT VOLI/FAULT = 1mAmax 180 mV7
Off-state leakageV/FAULT = 6.5Vmax 1 uA7
FAULT deglitchFAULT assertion or de-assertion due to overcurrent conditionmin 3 · typ 7.5 · max 11 ms7
FAULT deglitchFAULT assertion or de-assertion due to reverse-voltage conditionmin 2 · typ 4 · max 7 ms7
Thermal shutdown thresholdmin 155 °C7
Thermal shutdown threshold in current-limitmin 135 °C7
HysteresisThermal shutdowntyp 10 °C7

Pins, by the datasheet

7
1 OUT
Power-switch output. · p. 4
2 ILIM
External resistor sets the current-limit threshold; recommended 15kΩ ≤ RILIM ≤ 232kΩ. · p. 4
3 FAULT
Active-low output asserted during overcurrent, overtemperature, or reverse-voltage conditions. · p. 4
4 EN
Enable input; logic high turns on the power switch. · p. 4
5 GND
Ground connection; connect externally to PowerPAD. · p. 4
6 IN
Input voltage; connect a 0.1uF or greater ceramic capacitor to GND as close to the IC as possible. · p. 4
PAD PowerPAD
Internally connected to GND; heat-sinks the part to circuit-board traces. Connect externally to the GND pin. · p. 4

Parts like it

7

Questions

Is there a KiCad symbol and footprint for the TPS2553DRV?

Yes. The symbol is EasyEDA_Cloud:TPS2550DRVR and the footprint EasyEDA_Cloud:WSON-6_L2.0-W2.0-P0.65-TL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS2553DRV?

WSON-6-EP(2x2), with 7 pins. Its footprint is drawn on this page.

Where is the TPS2553DRV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS2553DRV?

JLCPCB lists it as part C138719, with 26,988 in stock; the sellers' links on this page open their listings.

What can replace the TPS2553DRV?

Parts like it in the library: the TPS25221DRV by Texas Instruments, the TPS2552DRV by Texas Instruments, the TPS2550DRVR by Texas Instruments and the TPS2550DRVT by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.