TPS2372-3RGWR
Texas InstrumentsExtended
-40℃~+125℃ 1 1.85A 100V 60W IEEE 802.3 bt(PoE++) PGOOD状态指示、PD检测与断开识别、Undervoltage Protection、Thermal Protection、Overcurrent Protection Powered Device (PD) VQFN-20(5x5) Power Over Ethernet (PoE) Controllers ROHS
- Part id
- ti/TPS2372-3RGWR
- Category
- Power Over Ethernet (PoE) Controllers
- Package
- VQFN-20(5x5)
- Pins
- 21
- In stock
- 109 at JLCPCB (C2876734)
Overview
The TPS2372-3RGWR is a power Over Ethernet (PoE) Controller made by Texas Instruments in a VQFN-20(5x5) package with 21 pins. -40℃~+125℃ 1 1.85A 100V 60W IEEE 802.3 bt(PoE++) PGOOD状态指示、PD检测与断开识别、Undervoltage Protection、Thermal Protection、Overcurrent Protection Powered Device (PD) VQFN-20(5x5) Power Over Ethernet (PoE) Controllers ROHS.
PCBKit's library has its KiCad symbol (TPS2372-4:TPS2372-3RGWR, from Antmicro) and its footprint (vqfn-20-5x5x1mm-p0-65mm:VQFN-20_5x5x1mm_P0.65mm, from Antmicro), ready for a KiCad board. 109 are in stock at JLCPCB (part C2876734).
Symbol
Footprint
From the datasheet
11- Supply, most
- 57 V · VDD, recommended operating maximum · p. 5
- Supply, absolute maximum
- 100 V · VDD, absolute maximum · p. 4
- Junction, hottest
- 125 °C · Maximum recommended junction temperature · p. 5
- Takes working
- 550 µA · Typical operating current, VDD = 40–57 V, startup completed · p. 7
- Takes at most
- 800 µA · Maximum operating current, VDD = 40–57 V, startup completed · p. 7
- Gives
- 1.2 A · Maximum recommended RTN sinking current · p. 5
- Current limit
- 1.85 A · Typical pass-device current limit, VRTN = 1.5 V · p. 6
- A pin gives at most
- 10 mA · PG, TPH, TPL, BT maximum sinking current per pin · p. 4
- Junction to air (RGW (VQFN))
- 40.2 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to board (RGW (VQFN))
- 17.9 K/W · Junction-to-board thermal resistance · p. 5
- Junction to case (RGW (VQFN))
- 34.6 K/W · Junction-to-case top thermal resistance · p. 5
What it is and has
11- PoE interface
- IEEE 802.3bt (Draft), Type 3 or Type 4 PD solution · p. 1
- Power level
- TPS2372-3: 60-W Type-3 operation · p. 1
- Hotswap MOSFET
- 100 V · p. 1
- Hotswap switch
- TPS2372-3: typical 0.3 Ω, 1.85 A current limit · p. 1
- Power indication
- Allocated power indicator outputs · p. 1
- Power Good
- PG output with inrush completion delay · p. 1
- Maintain Power Signature
- Automatic MPS · p. 1
- Autoclass
- Supported · p. 1
- PoE++
- Supports PoE++ PSE · p. 1
- Package
- 20-lead VQFN · p. 1
- PoE interface
- High-power PD interface with automatic MPS and Autoclass · p. 1
Around it
8- cap 0.1 µF
- between VDD and VSS; VDD bypass capacitor. · p. 3
- res 24.9 kΩ
- between DEN and VDD; Provides the PoE detection signature. · p. 3
- res 49.9kΩ_1%
- between REF and VSS; External resistor for internal reference. · p. 3
- res ~60.4 kΩ
- between MPS_DUTY and VSS; Selects 8.1% MPS duty cycle; open selects 5.4%, short selects 12.5%. · p. 3
- diode SMAJ58A
- between VDD and VSS; D1 TVS across the rectified PoE input; recommended for general indoor applications. · p. 28
- cap 0.1 μF
- between VDD and VSS; C1 input bypass capacitor, 100 V, 10% ceramic. · p. 29
- res 24.9 kΩ ± 1%
- between VDD and DEN; Recommended detection resistor RDEN. · p. 29
- res 49.9 kΩ
- between REF and VSS; RREF for the internal voltage reference. · p. 30
Specifications
90| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input voltage | VDD, DEN; relative to VSS | min -0.3 · max 100 V | 4 |
| Input voltage | RTN; I(RTN) = 0; relative to VSS | min -0.6 · max 100 V | 4 |
| Input voltage | IRSHDL_EN to RTN | min -0.3 · max 6.5 V | 4 |
| Input voltage | AUTCLS; relative to VSS | min -0.3 · max 6.5 V | 4 |
| Output voltage | CLSA, CLSB, REF, MPS_DUTY; do not apply voltages to these pins | min -0.3 · max 6.5 V | 4 |
| Output voltage | AMPS_CTL; do not apply voltages to this pin | min -0.3 · max 30 V | 4 |
| Voltage | PG to RTN | min -0.3 · max 100 V | 4 |
| Voltage | TPH, TPL, BT to RTN | min -0.3 · max 100 V | 4 |
| Sinking current | PG, TPH, TPL, BT | max 10 mA | 4 |
| Sinking current | DEN | max 1 mA | 4 |
| Sourcing current | CLSA, CLSB | max 65 mA | 4 |
| Sourcing current | AMPS_CTL | max 50 mA | 4 |
| Storage temperature Tstg | min -65 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins | min -2000 · max 2000 V | 4 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins | min -500 · max 500 V | 4 |
| Electrostatic discharge V(ESD) | IEC 61000-4-2 contact discharge; applied to Figure 22 circuit on TPS2372-4EVM-006 | min -8000 · max 8000 V | 4 |
| Electrostatic discharge V(ESD) | IEC 61000-4-2 air-gap discharge; applied to Figure 22 circuit on TPS2372-4EVM-006 | min -15000 · max 15000 V | 4 |
| Input voltage range | RTN, VDD; relative to VSS | min 0 · max 57 V | 5 |
| Voltage range | TPH, TPL, BT to RTN | min 0 · max 57 V | 5 |
| Voltage range | PG to RTN | min 0 · max 57 V | 5 |
| Sinking current | RTN; TPS2372-3 | max 1.2 A | 5 |
| Sinking current | PG, TPH, TPL, BT | max 3 mA | 5 |
| Resistance | CLSA, CLSB; voltage should not be externally applied | min 60 Ω | 5 |
| Resistance | AMPS_CTL; voltage should not be externally applied | min 1 kΩ | 5 |
| Resistance | REF; voltage should not be externally applied; NOM = 49.9 kΩ | min 48.9 · typ 49.9 · max 50.9 kΩ | 5 |
| Junction temperature | min -40 · max 125 °C | 5 | |
| Junction-to-ambient thermal resistance RθJA | TPS2372-3; RGW (VQFN), 20 pins | typ 40.2 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | TPS2372-3; RGW (VQFN), 20 pins | typ 34.6 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | TPS2372-3; RGW (VQFN), 20 pins | typ 17.9 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | TPS2372-3; RGW (VQFN), 20 pins | typ 0.5 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | TPS2372-3; RGW (VQFN), 20 pins | typ 17.8 °C/W | 5 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | TPS2372-3; RGW (VQFN), 20 pins | typ 3.4 °C/W | 5 |
| Bias current | DETECTION (DEN); DEN open, VVDD = 10.1 V, measure ISUPPLY(VDD, RTN, DEN), not in mark | min 3 · typ 4.8 · max 14 uA | 6 |
| DEN leakage current | VDEN = VVDD = 57 V | typ 0.5 · max 5 uA | 6 |
| Detection current | Measure ISUPPLY(VDD, RTN, DEN), VVDD = 1.4 V | min 53.8 · typ 56.5 · max 58.3 uA | 6 |
| Detection current | Measure ISUPPLY(VDD, RTN, DEN), VVDD = 10.1 V, not in mark | min 395 · typ 410 · max 417 uA | 6 |
| Disable threshold VPD_DIS | DEN falling | min 3 · typ 3.7 · max 5 V | 6 |
| Hysteresis VPD_DIS | DEN disable threshold | min 75 · typ 150 · max 250 mV | 6 |
| Classification A,B signature current ICLS | 13 V ≤ VVDD ≤ 21 V, measure IVDD + IDEN + IRTN; RCLSA or RCLSB = 1210 Ω | min 2.1 · typ 2.5 · max 2.9 mA | 6 |
| Classification A,B signature current ICLS | 13 V ≤ VVDD ≤ 21 V, measure IVDD + IDEN + IRTN; RCLSA or RCLSB = 249 Ω | min 9.9 · typ 10.6 · max 11.2 mA | 6 |
| Classification A,B signature current ICLS | 13 V ≤ VVDD ≤ 21 V, measure IVDD + IDEN + IRTN; RCLSA or RCLSB = 140 Ω | min 17.6 · typ 18.6 · max 19.4 mA | 6 |
| Classification A,B signature current ICLS | 13 V ≤ VVDD ≤ 21 V, measure IVDD + IDEN + IRTN; RCLSA or RCLSB = 90.9 Ω | min 26.5 · typ 27.9 · max 29.3 mA | 6 |
| Classification A,B signature current ICLS | 13 V ≤ VVDD ≤ 21 V, measure IVDD + IDEN + IRTN; RCLSA or RCLSB = 63.4 Ω | min 38 · typ 39.9 · max 42 mA | 6 |
| Autoclass signature current IAUTCLS | After tACS during 1st Class event | min 1 · max 4 mA | 6 |
| Class lower threshold VCL_ON | VVDD rising, ICLS ↑ | min 11.9 · typ 12.5 · max 13 V | 6 |
| Class lower threshold VCL_H | Hysteresis | min 1.4 · typ 1.6 · max 1.7 V | 6 |
| Class upper threshold VCU_ON | VVDD rising, ICLS↓ | min 21 · typ 22 · max 23 V | 6 |
| Class upper threshold VCU_H | Hysteresis | min 0.5 · typ 0.78 · max 0.9 V | 6 |
| Mark reset threshold VMSR | VVDD falling | min 3 · typ 3.9 · max 5 V | 6 |
| Mark state resistance | 2-point measurement at 5 V and 10.1 V | min 6 · typ 10 · max 12 kΩ | 6 |
| Leakage current | CLASSIFICATION (CLS); VVDD = 57 V, VCLS = 0 V, measure ICLS | max 1 uA | 6 |
| Long first class event timing tLCF_PD | Class 1st event time duration for new MPS | min 76 · typ 81.5 · max 86 ms | 6 |
| Autoclass signature timing tACS | AUTCLS During Class 1st event | min 76 · typ 81.5 · max 87 ms | 6 |
| AUTCLS pullup current | 13 V ≤ VVDD ≤ 21 V | min 30 · typ 34 · max 38 uA | 6 |
| On resistance rDS(on) | TPS2372-3; pass device RTN | typ 0.3 · max 0.55 Ω | 6 |
| Input bias current | VVDD = VRTN = 30 V, measure IRTN | max 50 uA | 6 |
| RTN leakage current | VVDD = VRTN = 100 V, VDEN = VVSS, measure IRTN | max 80 uA | 6 |
| Current limit | VRTN = 1.5 V; TPS2372-3 | min 1.55 · typ 1.85 · max 2.2 A | 6 |
| Inrush current limit | VRTN = 2 V, VVDD: 20 V → 48 V; TPS2372-3 | min 165 · typ 200 · max 237 mA | 6 |
| Inrush termination | Percentage of inrush current | min 65 · typ 90 · max 99 % | 6 |
| Inrush termination tINR_DEL | Inrush delay | min 78 · typ 81.5 · max 87 ms | 6 |
| Foldback threshold | VRTN rising | min 12.5 · typ 14.5 · max 15.5 V | 6 |
| Foldback deglitch time | VRTN rising to when current limit changes to inrush current limit | min 1.35 · typ 1.65 · max 1.95 ms | 6 |
| Output low voltage | POWER GOOD (PG); measure VPG – VRTN, IPG = 2 mA, VRTN = 2 V, VDD: 20 V → 48 V | typ 0.27 · max 0.5 V | 7 |
| Leakage current | POWER GOOD (PG); VPG = 57 V, VRTN = 0 V | max 10 uA | 7 |
| Leakage current | POWER GOOD (PG); VPG = 10 V, VRTN = 0 V | max 1 uA | 7 |
| Output low voltage VTPL | ITPL = 2 mA, after 2-, 3- or 5-event classification, startup has completed, VRTN = 0 V | typ 0.27 · max 0.5 V | 7 |
| Output low voltage VTPH | ITPH = 2 mA, after 4- or 5-event classification, startup has completed, VRTN = 0 V | typ 0.27 · max 0.5 V | 7 |
| Output low voltage VBT | IBT = 2 mA, after IEEE802.3bt classification, startup has completed, VRTN = 0 V | typ 0.27 · max 0.5 V | 7 |
| Leakage current | VTPL or VTPH or VBT = 7 V, VRTN = 0 V | max 1 uA | 7 |
| TPL, TPH, BT delay tTPLHBT | From PG: Low → open during startup to TPH and/or TPL and/or BT active | min 20 · typ 24 · max 28 ms | 7 |
| UVLO rising threshold VUVLO_R | VVDD rising | min 36.3 · typ 38.1 · max 40 V | 7 |
| UVLO falling threshold VUVLO_F | VVDD falling | min 30.5 · typ 32 · max 33.6 V | 7 |
| UVLO hysteresis VUVLO_H | typ 6.1 V | 7 | |
| Operating current | 40 V ≤ VVDD ≤ 57 V, startup has completed | typ 550 · max 800 uA | 7 |
| MPS DC supply current | Startup has completed, IRTN = 0 mA | max 0.8 mA | 7 |
| AMPS_CTL pulsed voltage | Startup has completed, IRTN < 20 mA, RMPS = 1 KΩ to 12 kΩ | min 23.1 · typ 24 · max 24.9 V | 7 |
| Automatic MPS falling current threshold | Startup has completed, IRTN threshold to generate AMPS_CTL pulses | min 18 · typ 28 · max 38 mA | 7 |
| Automatic MPS falling current threshold | Hysteresis on RTN current | typ 1 mA | 7 |
| MPS pulsed mode duty cycle for Type 1-2 PSE | MPS pulsed current duty cycle | min 25.8 · typ 26.1 · max 26.4 % | 7 |
| MPS pulsed mode duty cycle for Type 1-2 PSE | MPS pulsed current ON time | min 76 · typ 81.5 · max 87 ms | 7 |
| MPS pulsed mode duty cycle for Type 1-2 PSE | MPS pulsed current OFF time | typ 230 · max 250 ms | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current duty cycle, RMPS_DUTY > 230 kΩ | min 5.2 · typ 5.43 · max 5.6 % | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current ON time, RMPS_DUTY > 230 kΩ | min 14.5 · typ 15 · max 15.7 ms | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current duty cycle, RMPS_DUTY < 8 kΩ | min 12.3 · typ 12.5 · max 12.7 % | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current ON time, RMPS_DUTY < 8 kΩ | min 36 · typ 37.5 · max 39 ms | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current duty cycle, 43 kΩ < RMPS_DUTY < 77 kΩ | min 7.9 · typ 8.1 · max 8.3 % | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current ON time, 43 kΩ < RMPS_DUTY < 77 kΩ | min 22.2 · typ 23.1 · max 24 ms | 7 |
| MPS pulsed mode duty cycle for Type 3-4 PSE | MPS pulsed current OFF time, RMPS_DUTY from 0 Ω to open circuit | min 250 · typ 263.5 · max 277 ms | 7 |
| MPS_DUTY pullup current | min 14 · typ 17 · max 20 uA | 7 |
Pins, by the datasheet
21- 1 VDD
- Positive PoE input power rail; bypass with 0.1 uF to VSS. · p. 3
- 2 DEN
- Connect 24.9 kΩ to VDD for PoE detection; pull to VSS to disable the pass MOSFET during powered operation. · p. 3
- 3 CLSA
- Connect a resistor to VSS to program the first classification current. · p. 3
- 4 VSS
- Negative power rail derived from PoE source. · p. 3
- 5 VSS
- Negative power rail derived from PoE source. · p. 3
- 6 CLSB
- Connect a resistor to VSS to program the second classification current. · p. 3
- 7 REF
- Internal 1.5 V reference; connect a 49.9 kΩ, 1% resistor to VSS. · p. 3
- 8 AMPS_CTL
- Connect a suitably power-rated resistor to VSS to program automatic MPS current amplitude; leave open to disable automatic MPS. · p. 3
- 9 MPS_DUTY
- VSS-referenced MPS duty selection: open for 5.4%, about 60.4 kΩ to VSS for 8.1%, or short to VSS for 12.5%. · p. 3
- 10 AUTCLS
- Pull to VSS during classification to enable Autoclass; otherwise leave open. · p. 3
- 11 RTN
- Drain of PoE pass MOSFET; return line from the load to the controller. · p. 3
- 12 RTN
- Drain of PoE pass MOSFET; return line from the load to the controller. · p. 3
- 13 PG
- Active-high Power Good output referenced to RTN. · p. 3
- 14 NC
- No connect. · p. 3
- 15 NC
- No connect. · p. 3
- 16 IRSHDL_EN
- RTN-referenced PSE inrush delay enable; internally pulled up to 5.5 V; leave open to enable approximately 81.5 ms delay. · p. 3
- 17 TPL
- Binary-coded PSE allocated power output, active-low, referenced to RTN. · p. 3
- 18 TPH
- Binary-coded PSE allocated power output, active-low, referenced to RTN. · p. 3
- 19 BT
- Active-low output referenced to RTN indicating identification of an IEEE802.3bt Type 3 or 4 PSE. · p. 3
- 20 NC
- No connect; leave open. · p. 3
- — Pad
- Connect exposed thermal pad to VSS with a large fill area for heat dissipation. · p. 3
Ordering codes, by the datasheet
8- TPS2372-3RGWR
- VQFN (RGW), 20 pins · TPS2372-3; 3000-unit large tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-3RGWR.A
- VQFN (RGW), 20 pins · TPS2372-3; 3000-unit large tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-3RGWT
- VQFN (RGW), 20 pins · TPS2372-3; 250-unit small tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-3RGWT.A
- VQFN (RGW), 20 pins · TPS2372-3; 250-unit small tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-4RGWR
- VQFN (RGW), 20 pins · TPS2372-4; 3000-unit large tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-4RGWR.A
- VQFN (RGW), 20 pins · TPS2372-4; 3000-unit large tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-4RGWT
- VQFN (RGW), 20 pins · TPS2372-4; 250-unit small tape and reel; operating temperature -40 to 125 °C · p. 40
- TPS2372-4RGWT.A
- VQFN (RGW), 20 pins · TPS2372-4; 250-unit small tape and reel; operating temperature -40 to 125 °C · p. 40
Parts like it
2TPS2373-3RGWR
VQFN-20(5x5)-40℃~+125℃ 1 1.85A 100V 60W IEEE 802.3 at(PoE+)、IEEE 802.3 bt(PoE++) Powered Device (PD) VQFN-20(5x5) Power Over Ethernet (PoE) Controllers ROHSTexas InstrumentsPower Over Ethernet (PoE) ControllersTPS2372-4RGW
VQFN-20-EP(5x5)-40℃~+125℃ 100V 2.5A 40V~57V 90W IEEE 802.3 at(PoE+)、IEEE 802.3 bt(PoE++) VQFN-20-EP(5x5) Power Over Ethernet (PoE) Controllers ROHSTexas InstrumentsPower Over Ethernet (PoE) Controllers
Questions
Is there a KiCad symbol and footprint for the TPS2372-3RGWR?
Yes. The symbol is TPS2372-4:TPS2372-3RGWR and the footprint vqfn-20-5x5x1mm-p0-65mm:VQFN-20_5x5x1mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS2372-3RGWR?
VQFN-20(5x5), with 21 pins. Its footprint is drawn on this page.
Where is the TPS2372-3RGWR datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS2372-3RGWR?
JLCPCB lists it as part C2876734, with 109 in stock; the sellers' links on this page open their listings.
What can replace the TPS2372-3RGWR?
Parts like it in the library: the TPS2373-3RGWR by Texas Instruments and the TPS2372-4RGW by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.