Skip to the content
QFN-20(3x3)

TPD4S480RUK

Texas InstrumentsExtended

Overcurrent Protection、工作状态指示 QFN-20(3x3) Power Management - Specialized ROHS

Part id
ti/TPD4S480RUK
Category
Power Management, Specialized
Package
QFN-20(3x3)
Pins
21
In stock
2,663 at JLCPCB (C43131250)
Used on
1 open-source board

Overview

The TPD4S480RUK is a power Management, Specialized made by Texas Instruments in a QFN-20(3x3) package with 21 pins. Overcurrent Protection、工作状态指示 QFN-20(3x3) Power Management - Specialized ROHS.

2,663 are in stock at JLCPCB (part C43131250). 1 open-source board in 1 repository on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

The library has no footprint for this part yet.

From the datasheet

13
Supply, least
2.7 V · VPWR, recommended operating min · p. 5
Supply, most
4.5 V · VPWR, recommended operating max · p. 5
Supply, absolute maximum
5 V · VPWR, absolute max · p. 5
Junction, hottest
125 °C · Operating junction temperature max · p. 5
Takes working
112 µA · VPWR supply current typical, VPWR = 3.3 V, −40°C ≤ TJ ≤ +85°C · p. 7
Takes at most
160 µA · VPWR supply current max, VPWR = 4.5 V, −40°C ≤ TJ ≤ +85°C · p. 7
Gives
600 mA · VCONN current max per CC channel, TJ ≤ 105 ℃ · p. 5
Gives
1.25 A · VCONN current max per CC channel, TJ ≤ 85 ℃ · p. 5
Junction to air (QFN)
44.7 K/W · Junction-to-ambient thermal resistance · p. 6
Junction to board (QFN)
17.7 K/W · Junction-to-board thermal resistance · p. 6
Junction to case (QFN)
41.8 K/W · Junction-to-case (top) thermal resistance · p. 6
Works from
-40 °C · Operating temperature, min · p. 28
Works up to
125 °C · Operating temperature, max · p. 28

What it is and has

11
Short-to-VBUS overvoltage protection
4 channels: CC1, CC2, SBU1, SBU2 · p. 1
Connector-side voltage tolerance
63VDC on CC1, CC2, SBU1, SBU2 · p. 1
ESD protection
4 channels, IEC 61000-4-2 · p. 1
CC surge protection
±65V · p. 1
SBU surge protection
+65V/-35V · p. 1
VBUS divider
Integrated divider circuit with enable · p. 1
External FET control
Integrated FET driver · p. 1
Dead battery resistors
Integrated CC dead battery resistors · p. 1
Package
RUK, WQFN, 20 pins, 3mm × 3mm · p. 1
Short-to-VBUS overvoltage protection
4 channels · p. 1
IEC 61000-4-2 ESD protection
4 channels · p. 1

Around it

5
cap 0.1 µF
between VBIAS and GND; ESD support capacitor. Minimum 63-VDC rating; 100-VDC rating recommended to reduce derating. Place near the pin; effective capacitance 0.04–0.14 uF. · p. 4
cap 1 µF
between VPWR and GND; Nominal capacitance; minimum effective capacitance 0.3 uF. Place near the pin. · p. 6
cap 0.1 µF
between VBUS_LV and GND; Nominal capacitance; place near the pin. · p. 6
res 1.7–300 kΩ
between FLT and FLT Pull-up resistor power rail; Pull-up resistance range; pull-up power rail recommended range is 2.7–5.5 V. · p. 6
cap 1-µF
between VPWR and GND; Decoupling capacitor; place as close as possible to VPWR and connect to solid ground. · p. 19

Specifications

89
ParameterConditionsAs printedPage
Input voltage VIEPR_ENmin -0.3 · max 6 V5
Input voltage VIVPWRmin -0.3 · max 5 V5
Input voltage VIRPD_G1, RPD_G2, VBUSmin -0.3 · max 63 V5
Input voltage VIVBUS (VPWR = 0V)min -0.3 · max 24 V5
Input voltage VIVBUS (VPWR > 2.7V)min -0.3 · max 63 V5
Output voltage VOFLTmin -0.3 · max 6 V5
Output voltage VOVBIASmin -0.3 · max 63 V5
Output voltage VOVBUS_LVmin -0.3 · max 24 V5
Output voltage VOEPR_BLK_Gmin -0.3 · max 30 V5
I/O voltage VIOCC1, CC2, SBU1, SBU2min -0.3 · max 6 V5
I/O voltage VIOC_CC1, C_CC2, C_SBU1, C_SBU2min -0.3 · max 63 V5
Input voltage rise time (VI > 36V) triseCC1, CC2, SBU1, SBU2min 400 ns5
Operating junction temperature TJmin -40 · max 125 °C5
Storage temperature Tstgmin -65 · max 150 °C5
Electrostatic discharge V(ESD)IEC 61000-4-2, C_CC1, C_CC2; Contact discharge; VALUE = ±8000 Vmax 8000 V5
Electrostatic discharge V(ESD)IEC 61000-4-2, C_CC1, C_CC2; Air-gap discharge; VALUE = ±15000 Vmax 15000 V5
Electrostatic discharge V(ESD)IEC 61000-4-2, C_SBU1, C_SBU2; Contact discharge; VALUE = ±8000 Vmax 8000 V5
Electrostatic discharge V(ESD)IEC 61000-4-2, C_SBU1, C_SBU2; Air-gap discharge; VALUE = ±15000 Vmax 15000 V5
Lightning and Surge V(Surge)IEC 61000-4-5, C_CC1, C_CC2; VALUE = ±65 Vmax 65 V5
Lightning and Surge V(Surge)IEC 61000-4-5, C_SBU1, C_SBU2; VALUE = +65/-35 Vmin -35 · max 65 V5
Input voltage VIVPWRmin 2.7 · typ 3.3 · max 4.5 V5
Input voltage VIRPD_G1, RPD_G2min 0 · max 5.5 V5
Input voltage VIEPR_EN; maximum = VPWRmin 0 V5
Input voltage VIVBUSmin 0 · max 51 V5
Output voltage VOFLT Pull-up resistor power railmin 2.7 · max 5.5 V5
I/O voltage VIOCC1, CC2, C_CC1, C_CC2min 0 · max 5.5 V5
I/O voltage VIOSBU1, SBU2, C_SBU1, C_SBU2min 0 · max 4.3 V5
VCONN Current IVCONNCurrent flowing into CC1/2 and flowing out of C_CC1/2, TJ ≤ 105 ℃max 600 mA5
VCONN Current IVCONNCurrent flowing into CC1/2 and flowing out of C_CC1/2, TJ ≤ 85 ℃max 1.25 A5
Operating Junction Temperature TJmin -40 · max 125 ℃5
External ComponentsFLT Pull-up resistancemin 1.7 · max 300 kΩ6
External ComponentsVBIAS capacitancemin 0.04 · typ 0.1 · max 0.14 uF6
External ComponentsVPWR Capacitancemin 0.3 · typ 1 uF6
External ComponentsVBUS_LV Capacitancetyp 0.1 uF6
Junction-to-ambient thermal resistance RθJATPD4S480, QFN, 20 PINStyp 44.7 °C/W6
Junction-to-case (top) thermal resistance RθJC(top)TPD4S480, QFN, 20 PINStyp 41.8 °C/W6
Junction-to-board thermal resistance RθJBTPD4S480, QFN, 20 PINStyp 17.7 °C/W6
Junction-to-top characterization parameter ψJTTPD4S480, QFN, 20 PINStyp 0.7 °C/W6
Junction-to-board characterization parameter ψJBTPD4S480, QFN, 20 PINStyp 17.7 °C/W6
Junction-to-case (bottom) thermal resistance RθJC(bot)TPD4S480, QFN, 20 PINStyp 7.9 °C/W6
On Resistance of CC OVP FETs RONCCx = 5.5V, TJ ≤ 85 ℃typ 272 · max 420 mΩ6
Equivalent on Capacitance CON_CCCapacitance from CCx or C_CCx to GND when device is powered. Measure at VC_CCx/VCCx = 0V to 1.2V, f = 400kHz.min 40 · typ 74 · max 120 pF6
Dead Battery Pull-Down Resistors (only present when device is unpowered) RD_DBVC_CCx = 2.6Vmin 4.1 · typ 5.1 · max 6.1 kΩ6
Threshold voltage of the pull-down FET in series with RD during dead battery VTH_DBIC_CCx = 80uAmin 0.5 · typ 0.9 · max 1.2 V6
OVP Threshold on CC Pins VOVPCCPlace 5.5V on C_CCx. Step up C_CCx until FLT pin is asserted. Put 100mA load through the CC FET and see the FET shuts off.min 5.6 · typ 5.9 · max 6.2 V6
Hysteresis on CC OVP VOVPCC_HYSPlace 6.5 V on C_CCx. Step down the voltage on C_CCx until the FLT pin is deasserted. Measure difference between rising and falling OVP threshold for C_CCx.typ 50 mV6
On Bandwidth Single Ended (-3dB) BWONCC OVP switches; Measure the -3 dB bandwidth from C_CCx to CCx. Single ended measurement, 50-Ω system. Vcm = 0.1V to 1.2 V.typ 125 MHz6
Short-to-VBUS tolerance on the CC pins VSTBUS_CCHot-Plug C_CCx with a 1 meter USB Type C Cable, place a 30-Ω load on CCxmax 51 V6
Short-to-VBUS System-Side Clamping Voltage on the CC pins (CCx) VSTBUS_CC_CLAMPHot-Plug C_CCx with a 1 meter USB Type C Cable. Hot-Plug voltage C_CCx = 51 V. VPWR = 3.3 V. Place a 30-Ω load on CCx.typ 7 V6
On Resistance of SBU OVP FETs RONSBUx = 3.6 V. –40°C ≤ TJ ≤ +85°Ctyp 4 · max 6.8 Ω6
Equivalent on Capacitance CON_SBUCapacitance from SBUx or C_SBUx to GND when device is powered. Measure at VC_SBUx/VSBUx = 0.3V to 4.0V.typ 6 pF7
OVP Threshold on SBU Pins VOVPSBUPlace 3.6V on C_SBUx. Step up C_SBUx until FLT pin is asserted.min 4 · typ 4.2 · max 4.41 V7
Hysteresis on SBU OVP VOVPSBU_HYSPlace 5 V on C_CCx. Step down the voltage on C_CCx until the FLT pin is deasserted. Measure difference between rising and falling OVP threshold for C_SBUx.typ 50 mV7
On Bandwidth Single Ended (-3dB) BWONSBU OVP switches; Measure the -3 dB bandwidth from C_SBUx to SBUx. Single ended measurement, 50Ω system. Vcm = 0.1V to 3.6V.min 600 · typ 760 MHz7
Crosstalk XTALKMeasure crosstalk at f = 1 MHz from SBU1 to C_SBU2 or SBU2 to C_SBU1. Vcm1 = 3.6 V, Vcm2 = 0.3 V. Terminate open sides to 50Ω.typ -70 dB7
Short-to-VBUS tolerance on the SBU pins VSTBUS_SBUHot-Plug C_SBUx with a 1 meter USB Type C Cable. Put a 100-nF capacitor in series with a 40-Ω resistor to GND on SBUx.max 51 V7
Short-to-VBUS System-Side Clamping Voltage on the SBU pins (SBUx) VSTBUS_SBU_CLAMPHot-Plug C_SBUx with a 1 meter USB Type C Cable. Hot-Plug voltage C_SBUx = 51V. VPWR = 3.3 V. Put a 150-nF capacitor in series with a 40-Ω resistor to GND on SBUx.typ 7 V7
VBUS_LV to VBUS divider ratio, SPR Mode VBUS_DIV_SPRVBUS_LV/VBUS, EPR_EN = 0, VBUS = 4.5 - 21V, I_VBUS_LV = 0-20mAtyp 1 V/V7
VBUS_LV to VBUS divider ratio, EPR Mode VBUS_DIV_EPRVBUS_LV/VBUS, EPR_EN = 1, VBUS = 26.6-50.4, I_VBUS_LV = 0-20mAtyp 0.42 V/V7
Current from VBUS_LV IVBUSLVmax 20 mA7
VBUS to VBUS_LV forward voltage drop VFWD_VBUSLVI_VBUS_LV=20mA, VBUS=4.5V, EPR_EN=0typ 456 · max 700 mV7
VBUS to VBUS_LV forward voltage drop VFWD_VBUSLVI_VBUS_LV=20mA, VBUS=26V, EPR_EN=1typ 823 · max 940 mV7
Rising VBUS EPR enable threshold VEPR_THRESH_Rmin 22.7 · max 24 V7
Falling VBUS EPR enable threshold VEPR_THRESH_Fmin 22.4 · max 23.4 V7
Gate Drive voltage for EPR_BLK_G VEPR_BLK_G0 ≤ VBUS ≤ 22 Vmin 5 · max 12 V7
Gate Driver Sourcing Current IEPR_BLK_G0 ≤ VEPR_BLKG-VVBUS ≤ 5 V, 0 V ≤ VVBUS ≤ 22 V, measure IEPR_BLK_Gtyp 4 uA7
VPWR Under Voltage Lockout VPWR_UVLOPlace 1 V on VPWR and raise voltage until SBU or CC FETs turn-on.min 2.1 · typ 2.3 · max 2.6 V7
VPWR UVLO Hysteresis VPWR_UVLO_HYSPlace 3 V on VPWR and lower voltage until SBU or CC FETs turnoff; measure difference between rising and falling UVLO to calculate hysteresis.min 70 · typ 100 · max 130 mV7
VPWR supply current IVPWRVPWR = 3.3 V (typical), VPWR = 4.5 V (maximum). –40°C ≤ TJ ≤ +85°C.typ 112 · max 160 uA7
Leakage current for C_CCx pins when device is powered IC_CC_LEAKVPWR = 3.3 V, VC_CCx = 3.6 V, CCx pins are floating, measure leakage current into C_CCx pins.max 5 uA7
Leakage current for C_SBUx pins when device is powered IC_SBU_LEAKVPWR = 3.3 V, VC_SBUx = 3.6 V, SBUx pins are floating, measure leakage current into C_SBUx pins. Result should be same if SBUx side is biased and C_SBUx is left floating.-40°C ≤ TJ ≤ +85°Cmax 3.2 uA8
Leakage current for C_CCx pins when device is in OVP IC_CC_LEAK_OVPVPWR = 0 V or 3.3 V, VC_CCx = 51 V, CCx pins are set to 0 V, measure leakage current into C_CCx pins.max 1200 uA8
Leakage current for C_SBUx pins when device is in OVP IC_SBU_LEAK_OVPVPWR = 0 V or 3.3 V, VC_SBUx = 51 V, SBUx pins are set to 0 V, measure leakage current into C_SBUx pins.max 720 uA8
Leakage current for CC pins when device is in OVP ICC_LEAK_OVPVPWR = 0 V or 3.3 V, VC_CCx = 51 V, CCx pins are set to 0 V, measure leakage current out of CCx pins.max 30 uA8
Leakage current for SBU pins when device is in OVP ISBU_LEAK_OVPVPWR = 0 V, VC_SBUx = 51 V, SBUx pins are set to 0 V, measure leakage current into SBUx pins.min -1 · max 1 uA8
Low-level output voltage VOLIOL = 3mA. Measure voltage at FLT pin.max 0.4 V8
The rising over-temperature protection shutdown threshold TSD_RISINGmin 150 · typ 175 °C8
The falling over-temperature protection shutdown threshold TSD_FALLINGmin 130 · typ 140 °C8
The over-temperature protection shutdown threshold hysteresis TSD_HYSTtyp 35 °C8
Time from Crossing Rising VPWR UVLO until CC and SBU OVP FETs are on. tON_FETtyp 1.3 · max 3.5 ms8
Time from Crossing Rising VPWR UVLO until CC and SBU OVP FETs are on and the dead battery resistors are off. tON_FET_DBtyp 5.7 · max 9.5 ms8
Minimum slew rate for CC and FETs turn off during a power off. dVPWR_OFF/dtmin -0.5 V/us8
OVP response time on the CCx pins. Time from OVP asserted until OVP FETs turn off. tOVP_RESPONSE_CCtyp 70 ns8
OVP response time on the SBUx pins. Time from OVP asserted until OVP FETs turn off. tOVP_RESPONSE_SBUtyp 80 ns8
OVP recovery time on the CCx pins. Once an OVP has occurred, the minimum time duration until the CC FETs turn back on. OVP must be removed for CC FETs to turn back on. tOVP_RECOVERY_CCtyp 0.9 · max 2.3 ms8
OVP recovery time on the CCx pins. Once an OVP has occurred, the minimum time duration until the CC FETs turn back on and the dead battery resistors turn off. OVP must be removed for CC FETs to turn back on. tOVP_RECOVERY_CC_DBtyp 5 ms8
OVP recovery time on the SBUx pins. Once an OVP has occurred, the minimum time duration until the SBU FETs turn back on. OVP must be removed for SBU FETs to turn back on. tOVP_RECOVERY_SBUtyp 0.62 ms8
Time from OVP Asserted to /FLT assertion. FLT assertion is 10% of the maximum value. Set C_CCx or C_SBUx above the maximum OVP threshold. Start the time where it passes the typical OVP threshold value. tOVP_FLT_ASSERTIONtyp 20 us8
Time from CC FET turn on after an OVP to FLT deassertion. tOVP_FLT_DEASSERTIONtyp 5 ms8

Pins, by the datasheet

21
1 C_SBU1
Connector side of the SBU1 OVP FET; connect to a USB Type-C SBU pin, or a USB2.0 pin when protecting USB2.0. · p. 3
2 C_SBU2
Connector side of the SBU2 OVP FET; connect to a USB Type-C SBU pin, or a USB2.0 pin when protecting USB2.0. · p. 3
3 VBIAS
ESD support capacitor pin; place a 0.1-uF capacitor from this pin to ground. · p. 4
4 C_CC1
Connector side of the CC1 OVP FET; connect to either CC pin of the USB Type-C connector. · p. 3
5 C_CC2
Connector side of the CC2 OVP FET; connect to either CC pin of the USB Type-C connector. · p. 3
6 RPD_G2
Short to C_CC2 if dead battery resistors are needed; otherwise short to GND. · p. 3
7 RPD_G1
Short to C_CC1 if dead battery resistors are needed; otherwise short to GND. · p. 3
8 GND
Ground. · p. 3
9 FLT
Open drain for fault reporting. · p. 3
10 VPWR
2.7V to 4.5V power supply. · p. 4
11 CC2
System side of the CC2 OVP FET; connect to either CC pin of the CC/PD controller. · p. 3
12 CC1
System side of the CC1 OVP FET; connect to either CC pin of the CC/PD controller. · p. 3
13 GND
Ground. · p. 3
14 SBU2
System side of the SBU2 OVP FET; connect to an SBU MUX pin, or a USB2.0 Phy pin when protecting USB2.0. · p. 3
15 SBU1
System side of the SBU1 OVP FET; connect to an SBU MUX pin, or a USB2.0 Phy pin when protecting USB2.0. · p. 3
16 EPR_EN
EPR mode enable; assertion disables EPR_BLK_G and makes VBUS_LV divided VBUS. · p. 4
17 EPR_BLK_G
Gate driver for the optional VBUS blocking FET, enabled in SPR mode and disabled in EPR mode. · p. 4
18 GND
Ground. · p. 3
19 VBUS_LV
EPR VBUS divider output; divided VBUS when EPR_EN is asserted, equal to VBUS when de-asserted. · p. 4
20 VBUS
EPR VBUS divider input; tie to USB-C receptacle VBUS pins. · p. 4
- Thermal Pad
Internally connected to GND and used as a heatsink; connect to the PCB GND plane. · p. 4

Ordering codes, by the datasheet

2
TPD4S480RUKR
WQFN (RUK) · 20 pins; 5000 units, LARGE T&R; operating temperature -40 to 125 °C. · p. 28
TPD4S480RUKR.A
WQFN (RUK) · 20 pins; 5000 units, LARGE T&R; operating temperature refers to TPD4S480RUKR. · p. 28

Open-source boards using it

1
  • 4 layers42 × 42 mmSmol servo rp nodrv, the printed circuit board in 3D

    Smol servo rp nodrv

    dognotdog/smol_servo

    circuitry and software for controlling NEMA17 size brushless motors and stepper motors as servos.

    91 parts5

Parts like it

8

Questions

What package is the TPD4S480RUK?

QFN-20(3x3), with 21 pins.

Where is the TPD4S480RUK datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPD4S480RUK?

JLCPCB lists it as part C43131250, with 2,663 in stock; the sellers' links on this page open their listings.

What can replace the TPD4S480RUK?

Parts like it in the library: the MP8128GQ-Z by Monolithic Power Systems, the MP8128GQ-P by Monolithic Power Systems, the RT8248AGQW by Richtek Tech and the TS80002-QFNR by SEMTECH. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPD4S480RUK?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.