Skip to the content
1234567891011121314151617181920212223242526272829303132

TPA3116D2DAD

Texas InstrumentsExtended

-40℃~+85℃ -70dB 0.1% 102dB 2-Channel 35mA 4.5V~26V 50W×2@4Ω 90% Class D Filterless architecture、Overvoltage protection、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHS

Part id
ti/TPA3116D2DAD
Category
Audio Amplifiers
Package
HTSSOP-32-EP-6.1mm
Pins
32
In stock
327 at JLCPCB (C2865736)
Used on
7 open-source boards

Overview

The TPA3116D2DAD is an audio Amplifier made by Texas Instruments in a HTSSOP-32-EP-6.1mm package with 32 pins. -40℃~+85℃ -70dB 0.1% 102dB 2-Channel 35mA 4.5V~26V 50W×2@4Ω 90% Class D Filterless architecture、Overvoltage protection、Integrated PLL HTSSOP-32-EP-6.1mm Audio Amplifiers ROHS.

PCBKit's library has its footprint (EasyEDA_Cloud:HTSSOP-32_L11.0-W6.1-P0.65-LS8.1-BL, from EasyEDA), ready for a KiCad board. 327 are in stock at JLCPCB (part C2865736). 7 open-source boards in 5 repositories on GitHub use it.

Symbol

The library has no symbol for this part yet.

Footprint

1234567891011121314151617181920212223242526272829303132
EasyEDA_Cloud:HTSSOP-32_L11.0-W6.1-P0.65-LS8.1-BLFrom EasyEDA

From the datasheet

12
Supply, least
4.5 V · PVCC, AVCC, recommended operating min · p. 5
Supply, most
26 V · PVCC, AVCC, recommended operating max · p. 5
Supply, absolute maximum
30 V · PVCC, AVCC, absolute max · p. 5
Works from
-40 °C · Operating free-air temperature min · p. 5
Works up to
85 °C · Operating free-air temperature max · p. 5
Junction, hottest
150 °C · Operating junction temperature max · p. 5
Takes working
20 mA · Quiescent supply current typical, SDZ = 2 V, no load or filter, PVCC = 12 V · p. 6
Takes working
32 mA · Quiescent supply current typical, SDZ = 2 V, no load or filter, PVCC = 24 V · p. 6
Takes asleep
50 µA · Shutdown supply current typical, SDZ = 0.8 V, no load or filter, PVCC = 24 V · p. 6
Current limit
7.5 A · Over current trip point typical · p. 7
Junction to air (DAD)
14 K/W · Junction-to-ambient thermal resistance, specified heat sink · p. 6
Junction to board (DAD)
5.7 K/W · Junction-to-board characterization parameter, specified heat sink · p. 6

What it is and has

8
Amplifier architecture
Class-D stereo · p. 1
Output power
2 × 50 W into a 4-Ω BTL load at 21 V · p. 1
Power efficiency
>90% · p. 1
Switching frequency
Up to 1.2 MHz · p. 1
Synchronization
Master and slave · p. 1
Power limit
Programmable · p. 1
Audio inputs
Differential and single-ended · p. 1
Package
DAD, 32-pin HTSSOP, pad up · p. 1

Around it

32
cap 1 µF
between GVDD and GND; X5R ceramic decoupling capacitor; pin table specifies X7R. · p. 16
cap 220 nF
between BSNL and OUTNL; X5R or better ceramic bootstrap capacitor. · p. 4
cap 220 nF
between BSPL and OUTPL; X5R or better ceramic bootstrap capacitor. · p. 4
cap 220 nF
between BSNR and OUTNR; X5R or better ceramic bootstrap capacitor. · p. 4
cap 220 nF
between BSPR and OUTPR; X5R or better ceramic bootstrap capacitor. · p. 4
cap 1 µF
between PLIMIT and GND; For power-limit stability. · p. 15
res 5.6 kΩ
between GAIN/SLV and GND; Master mode, 20 dB gain; resistor to GVDD open; tolerance 5% or better. · p. 14
res 20 kΩ
between GAIN/SLV and GND; Master mode, 26 dB gain; pair with 100 kΩ to GVDD; tolerance 5% or better. · p. 14
res 100 kΩ
between GAIN/SLV and GVDD; Master mode, 26 dB gain; pair with 20 kΩ to GND; tolerance 5% or better. · p. 14
res 39 kΩ
between GAIN/SLV and GND; Master mode, 32 dB gain; pair with 100 kΩ to GVDD; tolerance 5% or better. · p. 14
res 100 kΩ
between GAIN/SLV and GVDD; Master mode, 32 dB gain; pair with 39 kΩ to GND; tolerance 5% or better. · p. 14
res 47 kΩ
between GAIN/SLV and GND; Master mode, 36 dB gain; pair with 75 kΩ to GVDD; tolerance 5% or better. · p. 14
res 75 kΩ
between GAIN/SLV and GVDD; Master mode, 36 dB gain; pair with 47 kΩ to GND; tolerance 5% or better. · p. 14
res 51 kΩ
between GAIN/SLV and GND; Slave mode, 20 dB gain; pair with 51 kΩ to GVDD; tolerance 5% or better. · p. 14
res 75 kΩ
between GAIN/SLV and GND; Slave mode, 26 dB gain; pair with 47 kΩ to GVDD; tolerance 5% or better. · p. 14
res 47 kΩ
between GAIN/SLV and GVDD; Slave mode, 26 dB gain; pair with 75 kΩ to GND; tolerance 5% or better. · p. 14
res 100 kΩ
between GAIN/SLV and GND; Slave mode, 32 dB gain; pair with 39 kΩ to GVDD; tolerance 5% or better. · p. 14
res 39 kΩ
between GAIN/SLV and GVDD; Slave mode, 32 dB gain; pair with 100 kΩ to GND; tolerance 5% or better. · p. 14
res 100 kΩ
between GAIN/SLV and GND; Slave mode, 36 dB gain; pair with 16 kΩ to GVDD; tolerance 5% or better. · p. 14
res 16 kΩ
between GAIN/SLV and GVDD; Slave mode, 36 dB gain; pair with 100 kΩ to GND; tolerance 5% or better. · p. 14
cap 1.5 µF
between Audio source and Audio input; Input AC coupling at 20 dB gain; 60 kΩ input impedance, 1.8 Hz high-pass filter; applies to each audio input. · p. 14
cap 3.3 µF
between Audio source and Audio input; Input AC coupling at 26 dB gain; 30 kΩ input impedance, 1.6 Hz high-pass filter; applies to each audio input. · p. 14
cap 5.6 µF
between Audio source and Audio input; Input AC coupling at 32 dB gain; 15 kΩ input impedance, 1.9 Hz high-pass filter; applies to each audio input. · p. 14
cap 10 µF
between Audio source and Audio input; Input AC coupling at 36 dB gain; 9 kΩ input impedance, 1.8 Hz high-pass filter; applies to each audio input. · p. 14
res 45 kΩ
between PLIMIT and GND; 24 V PVCC power-limit example; pair with 51 kΩ to GVDD for 3.3 V PLIMIT and 12.67 Vrms output. · p. 16
res 51 kΩ
between PLIMIT and GVDD; 24 V PVCC power-limit example; pair with 45 kΩ to GND for 3.3 V PLIMIT and 12.67 Vrms output. · p. 16
res 24 kΩ
between PLIMIT and GND; 12 V or 24 V PVCC power-limit example; pair with 51 kΩ to GVDD for 2.25 V PLIMIT and 9 Vrms output. · p. 16
res 51 kΩ
between PLIMIT and GVDD; 12 V or 24 V PVCC power-limit example; pair with 24 kΩ to GND for 2.25 V PLIMIT and 9 Vrms output. · p. 16
res 18 kΩ
between PLIMIT and GND; 12 V PVCC power-limit example; pair with 68 kΩ to GVDD for 1.5 V PLIMIT and 6.3 Vrms output. · p. 16
res 68 kΩ
between PLIMIT and GVDD; 12 V PVCC power-limit example; pair with 18 kΩ to GND for 1.5 V PLIMIT and 6.3 Vrms output. · p. 16
res 18 Ω
between Class-D output and Snubber capacitor; Optional series RC snubber to GND at each output; pair with 330 pF; application-specific design and tight return to IC GND required. · p. 21
cap 330 pF
between Snubber resistor and GND; Optional series RC snubber at each Class-D output; pair with 18 Ω; application-specific design required. · p. 21

Specifications

52
ParameterConditionsAs printedPage
Supply voltage VCCPVCC, AVCCmin -0.3 · max 30 V5
Input voltage VIINPL, INNL, INPR, INNRmin -0.3 · max 6.3 V5
Input voltage VIPLIMIT, GAIN / SLV, SYNC; maximum GVDD+0.3 Vmin -0.3 V5
Input voltage VIAM0, AM1, AM2, MUTE, SDZ, MODSEL; maximum PVCC+0.3 Vmin -0.3 V5
Slew rate, maximumAM0, AM1, AM2, MUTE, SDZ, MODSELmax 10 V/ms5
Operating free-air temperature TAmin -40 · max 85 °C5
Operating junction temperature TJmin -40 · max 150 °C5
Storage temperature Tstgmin -40 · max 125 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; value ±2000 Vmin -2000 · max 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; value ±500 Vmin -500 · max 500 V5
Supply voltage VCCPVCC, AVCCmin 4.5 · max 26 V5
High-level input voltage VIHAM0, AM1, AM2, MUTE, SDZ, SYNC, MODSELmin 2 V5
Low-level input voltage VILAM0, AM1, AM2, MUTE, SDZ, SYNC, MODSELmax 0.8 V5
Low-level output voltage VOLFAULTZ, RPULL-UP = 100 kΩ, PVCC = 26 Vmax 0.8 V5
High-level input current IIHAM0, AM1, AM2, MUTE, SDZ, MODSEL (VI = 2 V, VCC = 18 V)max 50 uA5
Minimum load Impedance RL(BTL)TPA3116D2; Output filter: L = 10 uH, C = 680 nF; NOM = 4 Ωmin 3.2 Ω5
Minimum load Impedance RL(PBTL)TPA3116D2; Output filter: L = 10 uH, C = 1 uFmin 1.6 Ω5
Output-filter Inductance LoMinimum output filter inductance under short-circuit conditionmin 1 uH5
Junction-to-ambient thermal resistance RθJATPA3116D2, DAD, 32 PINS; heat sink 14mm wide, 50mm long, 25mm hightyp 14 °C/W6
Junction-to-top characterization parameter ψJTTPA3116D2, DAD, 32 PINS; heat sink 14mm wide, 50mm long, 25mm hightyp 1.2 °C/W6
Junction-to-board characterization parameter ψJBTPA3116D2, DAD, 32 PINS; heat sink 14mm wide, 50mm long, 25mm hightyp 5.7 °C/W6
Class-D output offset voltage (measured differentially) | VOS |TA = 25°C, AVCC = PVCC = 12 V to 24 V, RL = 4 Ω; VI = 0 V, Gain = 36 dBtyp 1.5 · max 15 mV6
Quiescent supply current ICCTA = 25°C; SDZ = 2 V, No load or filter, PVCC = 12 Vtyp 20 · max 35 mA6
Quiescent supply current ICCTA = 25°C; SDZ = 2 V, No load or filter, PVCC = 24 Vtyp 32 · max 50 mA6
Quiescent supply current in shutdown mode ICC(SD)TA = 25°C; SDZ = 0.8 V, No load or filter, PVCC = 24 Vtyp 50 · max 400 uA6
Drain-source on-state resistance, measured pin to pin rDS(on)PVCC = 21 V, Iout = 500 mA, TJ = 25°Ctyp 120 mΩ6
Gain (BTL) GR1 = 5.6 kΩ, R2 = Openmin 19 · typ 20 · max 21 dB6
Gain (BTL) GR1 = 20 kΩ, R2 = 100 kΩmin 25 · typ 26 · max 27 dB6
Gain (BTL) GR1 = 39 kΩ, R2 = 100 kΩmin 31 · typ 32 · max 33 dB6
Gain (BTL) GR1 = 47 kΩ, R2 = 75 kΩmin 35 · typ 36 · max 37 dB6
Gain (SLV) GR1 = 51 kΩ, R2 = 51 kΩmin 19 · typ 20 · max 21 dB6
Gain (SLV) GR1 = 75 kΩ, R2 = 47 kΩmin 25 · typ 26 · max 27 dB6
Gain (SLV) GR1 = 100 kΩ, R2 = 39 kΩmin 31 · typ 32 · max 33 dB6
Gain (SLV) GR1 = 100 kΩ, R2 = 16 kΩmin 35 · typ 36 · max 37 dB6
Turn-on time tonSDZ = 2 Vtyp 10 ms6
Turn-off time tOFFSDZ = 0.8 Vtyp 2 us6
Gate drive supply GVDDIGVDD < 200 uAmin 6.4 · typ 6.9 · max 7.4 V6
Output voltage maximum under PLIMIT control VOV(PLIMIT) = 2 V; VI = 1 Vrmsmin 6.75 · typ 7.9 · max 8.75 V6
Power supply ripple rejection KSVRTA = 25°C, AVCC = PVCC = 12 V to 24 V, RL = 4 Ω; 200 mVPP ripple at 1 kHz, Gain = 20 dB, Inputs AC-coupled to GNDtyp -70 dB7
Continuous output power POTHD+N = 10%, f = 1 kHz, PVCC = 14.4 V; RL = 4 Ω, TA = 25°Ctyp 25 W7
Continuous output power POTHD+N = 10%, f = 1 kHz, PVCC = 21 V; RL = 4 Ω, TA = 25°Ctyp 50 W7
Total harmonic distortion + noise THD+NVCC = 21 V, f = 1 kHz, PO = 25 W (half-power)typ 0.1 %7
Output integrated noise Vn20 Hz to 22 kHz, A-weighted filter, Gain = 20 dBtyp 65 uV7
Output integrated noise Vn20 Hz to 22 kHz, A-weighted filter, Gain = 20 dBtyp -80 dBV7
CrosstalkVO = 1 Vrms, Gain = 20 dB, f = 1 kHztyp -100 dB7
Signal-to-noise ratio SNRMaximum output at THD+N < 1%, f = 1 kHz, Gain = 20 dB, A-weightedtyp 102 dB7
Oscillator frequency fOSCAM2=0, AM1=0, AM0=0min 376 · typ 400 · max 424 kHz7
Oscillator frequency fOSCAM2=0, AM1=0, AM0=1min 470 · typ 500 · max 530 kHz7
Oscillator frequency fOSCAM2=0, AM1=1, AM0=0min 564 · typ 600 · max 636 kHz7
Oscillator frequency fOSCAM2=0, AM1=1, AM0=1min 940 · typ 1000 · max 1060 kHz7
Thermal hysteresistyp 15 °C7
Over current trip pointTPA3116D2typ 7.5 A7

Pins, by the datasheet

33
1 MODSEL
Mode selection: LOW = BD mode, HIGH = 1 SPW mode; TTL levels with compliance to AVCC. · p. 4
2 SDZ
Shutdown: LOW = outputs Hi-Z, HIGH = outputs enabled; TTL levels with compliance to AVCC. · p. 4
3 FAULTZ
General fault reporting including overtemperature and DC detect; high for normal operation, low for fault. · p. 4
4 RINP
Positive right-channel audio input, biased at 3 V. · p. 4
5 RINN
Negative right-channel audio input, biased at 3 V. · p. 4
6 PLIMIT
Power limit adjustment; connect a divider from GVDD to GND, or directly to GVDD for no power limit. · p. 4
7 GVDD
Internal gate voltage supply; connect only a 1 uF X7R ceramic decoupling capacitor and PLIMIT and GAIN/SLV dividers. · p. 4
8 GAIN/SLV
Voltage divider selects gain and master or slave mode. · p. 4
9 GND
Ground. · p. 4
10 LINP
Positive left-channel audio input, biased at 3 V; connect to GND for PBTL mode. · p. 4
11 LINN
Negative left-channel audio input, biased at 3 V; connect to GND for PBTL mode. · p. 4
12 MUTE
HIGH = outputs Hi-Z, LOW = outputs enabled; TTL levels with compliance to AVCC. · p. 4
13 AM2
AM avoidance frequency selection. · p. 4
14 AM1
AM avoidance frequency selection. · p. 4
15 AM0
AM avoidance frequency selection. · p. 4
16 SYNC
Synchronization clock input/output; direction determined by GAIN/SLV. · p. 4
17 AVCC
Analog supply. · p. 4
18 PVCC
Power supply. · p. 4
19 PVCC
Power supply. · p. 4
20 BSNL
Negative left-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTNL. · p. 4
21 OUTNL
Negative left-channel output. · p. 4
22 GND
Ground. · p. 4
23 OUTPL
Positive left-channel output. · p. 4
24 BSPL
Positive left-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTPL. · p. 4
25 GND
Ground. · p. 4
26 BSNR
Negative right-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTNR. · p. 4
27 OUTNR
Negative right-channel output. · p. 4
28 GND
Ground. · p. 4
29 OUTPR
Positive right-channel output. · p. 4
30 BSPR
Positive right-channel bootstrap; connect a 220 nF X5R or better ceramic capacitor to OUTPR. · p. 4
31 PVCC
Power supply. · p. 4
32 PVCC
Power supply. · p. 4
33 PowerPAD
Connect to GND for best system performance; otherwise leave floating. · p. 4

Open-source boards using it

7
  • 4 layers128 × 128 mmSF 01 Compute Board, the printed circuit board in 3D

    SF 01 Compute Board

    sandgum/Triangulate-SF_01-Speaker-Frame

    A 24 inch Raspberry Pi-based Android digital picture frame attached to a 220W stereo Bluetooth speaker with DSP

    369 parts2
  • 2 layers120 × 80 mmSpeek amp, the printed circuit board in 3D

    Speek amp

    JBlitzar/speek

    speek monorepo

    102 parts1GPL-3.0
  • 4 layers99.8 × 64 mmAudio Amp v1, the printed circuit board in 3D

    Audio Amp v1

    Loredati-svg/TPA3116D2-Class-D-Amplifier

    2×50W stereo Class-D audio amplifier based on TI TPA3116D2 – KiCad PCB design

    124 parts1
  • 4 layers80 × 80 mmUnderwaterCom, the printed circuit board in 3D

    UnderwaterCom

    Frrrrrrrrrank/Underwater-Communication

    212 parts
  • 4 layers128 × 128 mmSF 01 Compute Board, the printed circuit board in 3D

    SF 01 Compute Board

    sandgum/Triangulate-SF_01-Speaker-Frame

    A 24 inch Raspberry Pi-based Android digital picture frame attached to a 220W stereo Bluetooth speaker with DSP

    334 parts2
  • 2 layers93.5 × 52.8 mmAudio Amp v1, the printed circuit board in 3D

    Audio Amp v1

    Loredati-svg/TPA3116D2-Class-D-Amplifier

    2×50W stereo Class-D audio amplifier based on TI TPA3116D2 – KiCad PCB design

    73 parts1
  • 2 layers80 × 49 mmPoweramp, the printed circuit board in 3D

    Poweramp

    colektamu/ECEN404-2026SP-TIAmplifier

    Files from 403 and 404

    30 parts

Parts like it

6

Questions

Is there a KiCad symbol and footprint for the TPA3116D2DAD?

Yes. the footprint EasyEDA_Cloud:HTSSOP-32_L11.0-W6.1-P0.65-LS8.1-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPA3116D2DAD?

HTSSOP-32-EP-6.1mm, with 32 pins. Its footprint is drawn on this page.

Where is the TPA3116D2DAD datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPA3116D2DAD?

JLCPCB lists it as part C2865736, with 327 in stock; the sellers' links on this page open their listings.

What can replace the TPA3116D2DAD?

Parts like it in the library: the TPA3116D2DADR by Texas Instruments, the TAS5828MDAD by Texas Instruments, the TPA3156D2DAD by Texas Instruments and the TPA3116D2QDADRQ1 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPA3116D2DAD?

7 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.