Skip to the content
1223

TLV76150DCY

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 1.6V@(1A) 16V 1A 5V 60uVrms 65uA 70dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Input under-voltage protection、Built-in soft-start Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/TLV76150DCY
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-223
Pins
4
In stock
329 at JLCPCB (C5845194)
Used on
12 open-source boards

Overview

The TLV76150DCY is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-223 package with 3 pins. -40℃~+125℃@(Tj) 1 1.6V@(1A) 16V 1A 5V 60uVrms 65uA 70dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Input under-voltage protection、Built-in soft-start Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Regulator_Linear:TLV76150DCY, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-223-3_TabPin2, from KiCad's library), ready for a KiCad board. 329 are in stock at JLCPCB (part C5845194). 12 open-source boards in 6 repositories on GitHub use it.

Symbol

1GND2VO3VI
Regulator_Linear:TLV76150DCYFrom KiCad's library

Footprint

1223
Package_TO_SOT_SMD:SOT-223-3_TabPin2From KiCad's library

From the datasheet

14
Supply, least
2.5 V · VIN, recommended operating min · p. 4
Supply, most
18 V · VIN, recommended operating max · p. 4
Supply, absolute maximum
20 V · VIN, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 15
Works up to
125 °C · Operating ambient temperature max · p. 15
Junction, hottest
150 °C · Operating junction temperature absolute max · p. 4
Takes working
65 µA · Quiescent current typical, IOUT = 0mA · p. 5
Gives
1 A · Continuous output current max, VIN ≥ 3 V · p. 4
Gives
800 mA · Continuous output current max, 2.5 V ≤ VIN < 3 V · p. 4
Current limit
1.1 A · Output current limit min, VOUT = 0.9 × VOUT(NOM), VIN ≥ 3.0V · p. 5
Dropout
900 mV · Dropout voltage typical, VIN ≥ 3.0V, IOUT = 1A · p. 5
Junction to air (DCY (SOT–223))
95.4 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (DCY (SOT–223))
55.6 K/W · Junction-to-case (top) thermal resistance · p. 5
Junction to board (DCY (SOT–223))
33.7 K/W · Junction-to-board thermal resistance · p. 5

What it is and has

5
Output type
Fixed output linear regulator · p. 1
Protection
Foldback current limit and thermal protection · p. 1
Internal soft start
500µs typical · p. 1
Package
4-pin SOT-223, 6.5mm x 7mm · p. 1
Protection
Undervoltage lockout and internal output pulldown · p. 10

Around it

3
cap 1 µF
between IN and GND; Nominal recommended input capacitance; use ceramic and place close to IN and GND. Not required for LDO stability. · p. 4
cap 2.2 µF
between OUT and GND; Nominal recommended output capacitance; specified range 1–220 uF, ESR 2–500 mΩ. Place close to OUT and GND. · p. 4
diode Schottky Diode
between OUT and IN; External reverse-current protection shown in Figure 7-1; use when reverse current is expected. · p. 14

Specifications

35
ParameterConditionsAs printedPage
Voltage VINAll voltages with respect to GNDmin -0.3 · max 20 V4
Voltage VOUTAll voltages with respect to GND; maximum is VIN + 0.3 V or 18 V, whichever is smallermin -0.3 V4
Operating junction (TJ) TJmin -50 · max 150 °C4
Storage (TSTG) TSTGmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; rating ±3000 Vmax 3000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; rating ±1000 Vmax 1000 V4
Input voltage VINmin 2.5 · max 18 V4
Output voltage VOUTFamily output voltage rangemin 0.8 · max 13.5 V4
Output current (2.5 V ≤ VIN < 3 V) IOUT2.5 V ≤ VIN < 3 Vmin 0 · max 0.8 A4
Output current (VIN ≥ 3 V) IOUTVIN ≥ 3 Vmin 0 · max 1 A4
Output capacitor ESR COUT ESRmin 2 · max 500 mΩ4
Output capacitor COUTNOM = 2.2 uF; effective output capacitance of 0.47 uF minimum required for stabilitymin 1 · typ 2.2 · max 220 uF4
Input capacitor CINNOM = 1 uF; not required for LDO stabilitytyp 1 uF4
Junction temperature TJmin -40 · max 125 °C4
Junction-to-ambient thermal resistance RθJADCY (SOT–223), 4 PINStyp 95.4 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DCY (SOT–223), 4 PINStyp 55.6 °C/W5
Junction-to-board thermal resistance RθJBDCY (SOT–223), 4 PINStyp 33.7 °C/W5
Junction-to-top characterization parameter ΨJTDCY (SOT–223), 4 PINStyp 13.9 °C/W5
Junction-to-board characterization parameter ΨJBDCY (SOT–223), 4 PINStyp 33.4 °C/W5
Nominal output accuracy VOUTTJ = 25°Cmin -1 · max 1 %5
Output accuracy over temperature VOUTVIN ≥ 3.0V, VOUT(NOM) ≤ 9.0V, 1mA ≤ IOUT ≤ 1A; minimum is split across text lines and omittedmax 1.75 %5
Line regulation ΔVOUT(ΔVIN)VOUT(NOM) ≤ 9.0V, VOUT(NOM) + 1.5V ≤ VIN ≤ 18V, IOUT = 10mAmax 0.02 %/V5
Load regulation ΔVOUT(ΔIOUT)1mA ≤ IOUT ≤ 1A, VIN ≥ 3.0Vtyp 0.1 · max 0.75 %/A5
Dropout voltage VDOVIN ≥ 3.0V, IOUT = 1Atyp 0.9 · max 1.6 V5
Output current limit ICLVOUT = 0.9 x VOUT(NOM), VIN ≥ 3.0Vmin 1.1 · max 1.6 A5
Short-circuit current limit ISCVOUT = 0Vmin 150 · typ 250 · max 350 mA5
Quiescent current IQIOUT = 0mAtyp 65 · max 100 uA5
Output pulldown current IPULLDOWNVIN = 1.8V, VOUT = 2.5Vmin 0.7 · max 1.1 mA5
Power-supply rejection ratio PSRRVIN = 3.3V, VOUT = 1.8V, IOUT = 300mA, f = 120Hztyp 70 dB5
Output noise voltage VnBW = 10Hz to 100kHz, VIN = 3.3V, VOUT = 0.8V, IOUT = 100mAtyp 60 uVRMS5
UVLO threshold rising VUVLO+VIN risingtyp 2.2 · max 2.4 V5
UVLO hysteresis VUVLO(HYS)typ 130 mV5
UVLO threshold falling VUVLO-VIN fallingmin 1.9 V5
Thermal shutdown temperature TSD(shutdown)Temperature increasingtyp 180 ºC5
Thermal shutdown reset temperature TSD(reset)Temperature fallingtyp 160 ºC5

Pins, by the datasheet

4
1 GND
Ground pin. · p. 3
2 OUT
Output pin; place the recommended output capacitor as close to OUT and GND as possible. · p. 3
Tab OUT
Output tab, connected to OUT. · p. 3
3 IN
Input pin; place the recommended input capacitor as close to IN and GND as possible. · p. 3

Open-source boards using it

12See all 12
  • 2 layers100.7 × 138.5 mmVCUinvertor, the printed circuit board in 3D

    VCUinvertor

    EVR-Tuiasi/Shield_VCU_Invertoare

    158 parts1
  • 4 layers100 × 50 mmController, the printed circuit board in 3D

    Controller

    usbalbin/hw-half-bridge

    226 parts
  • 2 layers75 × 55 mmRectifier, the printed circuit board in 3D

    Rectifier

    duanestorey/hifi-amp

    A high-fidelity four-channel amplifier with active-crossovers and room correction

    80 parts1
  • 2 layers70 × 55 mmRectifier, the printed circuit board in 3D

    Rectifier

    duanestorey/hifi-amp

    A high-fidelity four-channel amplifier with active-crossovers and room correction

    74 parts1
  • 2 layers70 × 55 mmRectifier, the printed circuit board in 3D

    Rectifier

    duanestorey/hifi-amp

    A high-fidelity four-channel amplifier with active-crossovers and room correction

    32 parts1
  • 6 layers54.3 × 22 mmMelty, the printed circuit board in 3D

    Melty

    mikewen2024/Eyeliner

    A 1lb (antweight) melty-brain combat robot. A melty-brain spins the entire chassis at 1,000–2,000 RPM while pulsing drive motors 100 times/second to achieve controlled translational movement — maximum hitting power, and…

    39 parts1MIT
  • 2 layers105 × 42.8 mmPIPO JAMON, the printed circuit board in 3D

    PIPO JAMON

    AgustinPrietoValdez/competition-robots

    Custom competition robots — maze/micromouse (MISA), sumo (TATAMI 1) & mini-sumo (RUCHO). KiCad PCBs, STM32/Arduino firmware, Fusion 360. National champion & international prizes — by EDNAROBOTICS.

    33 partsMIT
  • 2 layers91 × 42 mmPlacadelPocho, the printed circuit board in 3D

    PlacadelPocho

    AgustinPrietoValdez/competition-robots

    Custom competition robots — maze/micromouse (MISA), sumo (TATAMI 1) & mini-sumo (RUCHO). KiCad PCBs, STM32/Arduino firmware, Fusion 360. National champion & international prizes — by EDNAROBOTICS.

    29 partsMIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV76150DCY?

Yes. The symbol is Regulator_Linear:TLV76150DCY and the footprint Package_TO_SOT_SMD:SOT-223-3_TabPin2, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV76150DCY?

SOT-223, with 3 pins. Its footprint is drawn on this page.

Where is the TLV76150DCY datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV76150DCY?

JLCPCB lists it as part C5845194, with 329 in stock; the sellers' links on this page open their listings.

What can replace the TLV76150DCY?

Parts like it in the library: the AMS1117-5.0 by Advanced Monolithic Systems, the AMS1117-5.0 by UMW, the AZ1117CH2-5.0TRG1 by Diodes Incorporated and the LM1117S-5.0 by HTC. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV76150DCY?

12 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.