Skip to the content
12345

TLV70018DDC

Texas InstrumentsExtended

-40℃~+125℃@(Tj) 1 1.8V 200mA 250mV@(200mA) 31uA 48uVrms 5.5V 68dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS

Part id
ti/TLV70018DDC
Category
Voltage Regulators, Linear, Low Drop Out (LDO) Regulators
Package
SOT-23-5
Pins
5
In stock
2,860 at JLCPCB (C79924)
Used on
1 open-source board

Overview

The TLV70018DDC is a voltage Regulators, Linear, Low Drop Out (LDO) Regulator made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃@(Tj) 1 1.8V 200mA 250mV@(200mA) 31uA 48uVrms 5.5V 68dB@(1kHz) Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Enable SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHS.

PCBKit's library has its KiCad symbol (Pinmap_Generic:Regulator_Linear_1IN_2GND_3EN_4NC_5OUT, from PCBKit's generic symbols) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 2,860 are in stock at JLCPCB (part C79924). 1 open-source board in 1 repository on GitHub use it.

Symbol

1IN3EN5OUT2GND
Pinmap_Generic:Regulator_Linear_1IN_2GND_3EN_4NC_5OUTFrom PCBKit's generic symbols

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

12
Supply, least
2 V · VIN, recommended operating min · p. 5
Supply, most
5.5 V · VIN, recommended operating max · p. 5
Supply, absolute maximum
6 V · VIN, absolute max · p. 5
Junction, hottest
150 °C · Junction temperature, absolute max · p. 5
Takes working
31 µA · Ground pin current, typical, IOUT = 0 mA · p. 6
Takes asleep
400 nA · Shutdown ground current, typical, VEN ≤ 0.4 V, VIN = 2 V · p. 6
Takes asleep
1 µA · Shutdown ground current, typical, VEN ≤ 0.4 V, VIN = 2–4.5 V · p. 6
Gives
200 mA · IOUT, recommended continuous max · p. 5
Current limit
220 mA · Output current limit, min, VOUT = 0.9 × VOUT(nom) · p. 6
Junction to air (DDC [SOT])
235.9 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to board (DDC [SOT])
54 K/W · Junction-to-board thermal resistance · p. 5
Junction to case (DDC [SOT])
61.9 K/W · Junction-to-case (top) thermal resistance · p. 5

What it is and has

3
Accuracy
2% · p. 1
Protection
Thermal shutdown and overcurrent protection · p. 1
Output capacitor stability
Effective capacitance of 0.1 μF · p. 1

Around it

2
cap 1 μF
between IN and GND; Recommended ceramic input capacitor; X5R or X7R type. · p. 4
cap 1 μF
between OUT and GND; Ceramic output capacitor for stability; X5R or X7R type. Effective capacitance must be at least 0.1 uF and ESR less than 200 mΩ. · p. 4

Specifications

33
ParameterConditionsAs printedPage
Voltage VINOver operating junction temperature rangemin -0.3 · max 6 V5
Voltage VENMaximum is VIN + 0.3 V or 6 V, whichever is lessmin -0.3 · max 6 V5
Voltage VOUTOver operating junction temperature rangemin -0.3 · max 6 V5
Operating junction TJmin -55 · max 150 °C5
Storage Tstgmin -55 · max 150 °C5
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; rating ±2000 Vmax 2000 V5
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; rating ±500 Vmax 500 V5
VIN VINOver operating free-air temperature rangemin 2 · max 5.5 V5
IOUT IOUTOver operating free-air temperature rangemin 0 · max 200 mA5
Junction-to-ambient thermal resistance RθJADDC [SOT], 5 PINStyp 235.9 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DDC [SOT], 5 PINStyp 61.9 °C/W5
Junction-to-board thermal resistance RθJBDDC [SOT], 5 PINStyp 54 °C/W5
Junction-to-top characterization parameter ψJTDDC [SOT], 5 PINStyp 0.8 °C/W5
Junction-to-board characterization parameter ψJBDDC [SOT], 5 PINStyp 53.4 °C/W5
Input voltage range VINmin 2 · max 5.5 V6
DC output accuracy VOUT–40°C ≤ TJ ≤ +125°Cmin -2 · max 2 %6
Line regulation ΔVOUT(ΔVIN)VOUT(nom) + 0.3 V ≤ VIN ≤ 5.5 V, IOUT = 10 mAtyp 1 · max 5 mV6
Load regulation ΔVOUT(ΔIOUT)0 mA ≤ IOUT ≤ 200 mAtyp 1 · max 15 mV6
Output current limit ICLVOUT = 0.9 × VOUT(nom)min 220 · max 860 mA6
Ground pin current IGNDIOUT = 0 mAtyp 31 · max 55 uA6
Ground pin current IGNDIOUT = 200 mA, VIN = VOUT + 0.5 Vtyp 270 uA6
Ground pin current (shutdown) ISHDNVEN ≤ 0.4 V, VIN = 2 Vtyp 400 nA6
Ground pin current (shutdown) ISHDNVEN ≤ 0.4 V, 2 V ≤ VIN ≤ 4.5 Vtyp 1 · max 2 uA6
Power-supply rejection ratio PSRRVIN = 2.3 V, VOUT = 1.8 V, IOUT = 10 mA, f = 1 kHztyp 68 dB6
Output noise voltage VnBW = 100 Hz to 100 kHz, VIN = 2.3 V, VOUT = 1.8 V, IOUT = 10 mAtyp 48 uVRMS6
Start-up time tSTRCOUT = 1 uF, IOUT = 200 mA; time from EN assertion to 0.98 × VOUT(nom)typ 100 us6
Enable pin high (enabled) VEN(high)Maximum is VINmin 0.9 V6
Enable pin low (disabled) VEN(low)min 0 · max 0.4 V6
Enable pin current IENVIN = VEN = 5.5 Vtyp 0.04 · max 0.5 uA6
Undervoltage lockout UVLOVIN risingtyp 1.9 V6
Thermal shutdown temperature TsdShutdown, temperature increasingtyp 160 °C6
Thermal shutdown temperature TsdReset, temperature decreasingtyp 140 °C6
Operating junction temperature TJmin -40 · max 125 °C6

Pins, by the datasheet

5
1 IN
Input pin; a 1-uF ceramic capacitor to ground is recommended for stability and transient performance. · p. 4
2 GND
Ground pin. · p. 4
3 EN
Enable input; above 0.9 V enables the regulator, below 0.4 V enters shutdown. · p. 4
4 NC
No connection; can be tied to ground to improve thermal dissipation. · p. 4
5 OUT
Regulated output voltage; a 1-uF ceramic capacitor to ground is needed for stability. · p. 4

Open-source boards using it

1
  • 6 layers170 × 120 mmRv2 final, the printed circuit board in 3D

    Rv2 final

    misko/prompt2device

    The separate vNext PCB skill and orchestrator package is available alongside the reference workflow below; existing projects keep their accepted toolchain until an explicit migration.

    203 parts3MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TLV70018DDC?

Yes. The symbol is Pinmap_Generic:Regulator_Linear_1IN_2GND_3EN_4NC_5OUT and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TLV70018DDC?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the TLV70018DDC datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TLV70018DDC?

JLCPCB lists it as part C79924, with 2,860 in stock; the sellers' links on this page open their listings.

What can replace the TLV70018DDC?

Parts like it in the library: the AP2112K-1.8TRG1 by Diodes Incorporated, the ME6211C18M5G-N by MICRONE, the RT9078-18GJ5 by RICHTEK and the LP5907MFX-1.8 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TLV70018DDC?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.