
TLC59283DBQ
Texas InstrumentsExtended
-40℃~+85℃ 0V~10V 16 3% 35MHz 35mA、45mA 3V~5.5V Buck Built-in PWM SSOP-24-150mil LED Drivers ROHS
- Part id
- ti/TLC59283DBQ
- Category
- LED Drivers
- Package
- SSOP-24-150mil
- Pins
- 24
- In stock
- 648 at JLCPCB (C702075)
- Used on
- 7 open-source boards
Overview
The TLC59283DBQ is a LED Driver made by Texas Instruments in a SSOP-24-150mil package with 24 pins. -40℃~+85℃ 0V~10V 16 3% 35MHz 35mA、45mA 3V~5.5V Buck Built-in PWM SSOP-24-150mil LED Drivers ROHS.
PCBKit's library has its KiCad symbol (4ms-ic:TLC59283DBQR, from 4ms) and its footprint (EasyEDA_Cloud:SSOP-24_L8.7-W3.9-P0.64-LS6.0-BL, from EasyEDA), ready for a KiCad board. 648 are in stock at JLCPCB (part C702075). 7 open-source boards in 6 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
13- Supply, least
- 3 V · VCC, recommended operating min · p. 3
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 3
- Supply, absolute maximum
- 6 V · VCC, absolute max · p. 2
- Works from
- -40 °C · Operating free-air temperature min · p. 3
- Works up to
- 85 °C · Operating free-air temperature max · p. 3
- Junction, hottest
- 150 °C · Operating junction temperature absolute max · p. 2
- Takes working
- 8 mA · VCC supply current typical, all outputs on, RIREF = 1.5 kΩ · p. 4
- Takes at most
- 11 mA · VCC supply current max, all outputs on, RIREF = 1.5 kΩ · p. 4
- Gives
- 35 mA · Per-channel sink current max, 3 V ≤ VCC ≤ 3.6 V · p. 3
- Gives
- 45 mA · Per-channel sink current max, 3.6 V < VCC ≤ 5.5 V · p. 3
- A pin gives at most
- 50 mA · OUT0 to OUT15 dc output current absolute max per pin · p. 2
- Data rate, most
- 35 Mbit/s · Serial data shift clock max · p. 3
- Edge
- 3 ns · SOUT rise and fall time typical · p. 5
What it is and has
5- LED channels
- 16, constant-current sink, on/off control · p. 1
- Logic interface
- CMOS logic-level I/O · p. 1
- Ghost reduction
- Pre-charge FET · p. 1
- Noise reduction
- Grouped switching delay · p. 1
- LED supply voltage
- Up to 10 V · p. 1
Around it
10- res 1.18 kΩ
- between IREF and GND; RIREF, typical; 45 mA output, VCC > 3.6 V only · p. 14
- res 1.32 kΩ
- between IREF and GND; RIREF, typical; 40 mA output, VCC > 3.6 V only · p. 14
- res 1.51 kΩ
- between IREF and GND; RIREF, typical; 35 mA output · p. 14
- res 1.76 kΩ
- between IREF and GND; RIREF, typical; 30 mA output · p. 14
- res 2.12 kΩ
- between IREF and GND; RIREF, typical; 25 mA output · p. 14
- res 2.65 kΩ
- between IREF and GND; RIREF, typical; 20 mA output · p. 14
- res 3.53 kΩ
- between IREF and GND; RIREF, typical; 15 mA output · p. 14
- res 5.29 kΩ
- between IREF and GND; RIREF, typical; 10 mA output · p. 14
- res 10.6 kΩ
- between IREF and GND; RIREF, typical; 5 mA output · p. 14
- res 26.5 kΩ
- between IREF and GND; RIREF, typical; 2 mA output · p. 14
Specifications
53| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply VCC | Over operating free-air temperature range | min -0.3 · max 6 V | 2 |
| Input range, SIN, SCLK, LAT, BLANK, IREF VIN | Maximum VCC + 0.3 V | min -0.3 V | 2 |
| Output range, SOUT VOUT | Maximum VCC + 0.3 V | min -0.3 V | 2 |
| Output range, OUT0 to OUT15 VOUT | min -0.3 · max 11 V | 2 | |
| Output (dc), OUT0 to OUT15 IOUT | max 50 mA | 2 | |
| Operating junction TJ(MAX) | max 150 °C | 2 | |
| Storage range Tstg | min -55 · max 150 °C | 2 | |
| Human body model (HBM) ESD | max 3000 V | 2 | |
| Charged device model (CDM) ESD | max 2000 V | 2 | |
| Supply voltage VCC | TA = –40°C to +85°C | min 3 · max 5.5 V | 3 |
| Voltage applied to output VO | OUT0 to OUT15 | max 10 V | 3 |
| Output current High IOH | SOUT | max -2 mA | 3 |
| Output current Low IOL | SOUT | max 2 mA | 3 |
| Constant output sink current IOLC | OUT0 to OUT15, 3 V ≤ VCC ≤ 3.6 V | min 2 · max 35 mA | 3 |
| Constant output sink current IOLC | OUT0 to OUT15, 3.6 V < VCC ≤ 5.5 V | min 2 · max 45 mA | 3 |
| Temperature range Operating free-air TA | min -40 · max 85 °C | 3 | |
| Temperature range Operating junction TJ | min -40 · max 125 °C | 3 | |
| Data shift clock frequency fCLK (SCLK) | SCLK; VCC = 3 V to 5.5 V | max 35 MHz | 3 |
| Pulse duration tWH0 | SCLK | min 10 ns | 3 |
| Pulse duration tWL0 | SCLK | min 10 ns | 3 |
| Pulse duration tWH1 | LAT | min 20 ns | 3 |
| Pulse duration tWH2 | BLANK | min 100 ns | 3 |
| Pulse duration tWL2 | BLANK | min 50 ns | 3 |
| Setup time tSU0 | SIN↑↓ – SCLK↑ | min 4 ns | 3 |
| Setup time tSU1 | LAT↓ – SCLK↑ | min 10 ns | 3 |
| Hold time tH0 | SIN↑↓ – SCLK↑ | min 4 ns | 3 |
| Hold time tH1 | LAT↓ – SCLK↑ | min 10 ns | 3 |
| Output voltage Low VOL | IOL = 2 mA at SOUT | max 0.4 V | 4 |
| Reference voltage output VIREF | RIREF = 1.5 kΩ, TA = +25°C | typ 1.208 V | 4 |
| Input current IIN | VIN = VCC or GND at SIN and SCLK | min -1 · max 1 uA | 4 |
| Supply current (VCC) ICC0 | SIN, SCLK, LAT = GND, BLANK = VOUTn = VCC, RIREF = open | typ 1 · max 2 mA | 4 |
| Supply current (VCC) ICC1 | SIN, SCLK, LAT = GND, BLANK = VOUTn = VCC, RIREF = 3 kΩ (IOUT = 17.6 mA target) | typ 3 · max 4 mA | 4 |
| Supply current (VCC) ICC2 | All OUTn = ON, SIN, SCLK, LAT, BLANK = GND, VOUTn = 0.8 V, RIREF = 3 kΩ | typ 7 · max 9 mA | 4 |
| Supply current (VCC) ICC3 | All OUTn = ON, SIN, SCLK, LAT, BLANK = GND, VOUTn = 0.8 V, RIREF = 1.5 kΩ (IOUT = 35.3 mA target) | typ 8 · max 11 mA | 4 |
| Constant output current IOLC | All OUTn = ON, VOUTn = VOUTfix = 0.8 V, RIREF = 1.5 kΩ, TA = +25°C (see Figure 8) | min 32.9 · typ 35.3 · max 37.7 mA | 4 |
| Output leakage current IOLKG0 | All OUTn = OFF, VOUTn = VOUTfix = 10 V, BLANK = VCC, RIREF = 1.5 kΩ (see Figure 8); TJ = +25°C | max 0.1 uA | 4 |
| Output leakage current IOLKG0 | All OUTn = OFF, VOUTn = VOUTfix = 10 V, BLANK = VCC, RIREF = 1.5 kΩ (see Figure 8); TJ = +85°C | max 0.2 uA | 4 |
| Output leakage current IOLKG0 | All OUTn = OFF, VOUTn = VOUTfix = 10 V, BLANK = VCC, RIREF = 1.5 kΩ (see Figure 8); TJ = +125°C | typ 0.07 · max 0.5 uA | 4 |
| Constant-current error Channel-to-channel (1) ΔIOLC0 | All OUTn = ON, VOUTn = VOUTfix = 0.8 V, RIREF = 1.5 kΩ, TA = +25°C (see Figure 8); values are ± | typ 1.4 · max 3 % | 4 |
| Constant-current error Device-to-device (2) ΔIOLC1 | All OUTn = ON, VOUTn = VOUTfix = 0.8 V, RIREF = 1.5 kΩ, TA = +25°C (see Figure 8); values are ± | typ 2 · max 4 % | 4 |
| Line regulation (3) ΔIOLC2 | All OUTn = ON, VOUTn = VOUTfix = 0.8 V, RIREF = 1.5 kΩ, VCC = 3 V to 5.5 V; values are ± | typ 0.05 · max 1 %/V | 4 |
| Load regulation (4) ΔIOLC3 | All OUTn = ON, VOUTn = 0.8 V to 3 V, VOUTfix = 0.8 V, RIREF = 1.5 kΩ; values are ± | typ 0.5 · max 1 %/V | 4 |
| Resistor Pull-up RPUP | BLANK | min 250 · typ 500 · max 750 kΩ | 4 |
| Resistor Pull-down RPDWN | LAT | min 250 · typ 500 · max 750 kΩ | 4 |
| Pre-charge FET on-resistance RPCHG | VCC = 5.0 V, VOUTn = 0 V, OUT0 to OUT15, BLANK = VCC, TA = +25°C | typ 3 · max 6 kΩ | 4 |
| Rise time tR0 | SOUT (see Figure 7) | typ 3 · max 10 ns | 5 |
| Rise time tR1 | OUTn (see Figure 6) | typ 44 ns | 5 |
| Fall time tF0 | SOUT (see Figure 7) | typ 3 · max 10 ns | 5 |
| Fall time tF1 | OUTn (see Figure 6) | typ 44 ns | 5 |
| Propagation delay time tD0 | SCLK↑ to SOUT↑↓ | typ 11 · max 20 ns | 5 |
| Propagation delay time tD1 | LAT↑ or BLANK↑↓ to OUT0 on or off, TA = +25°C | typ 60 · max 100 ns | 5 |
| Propagation delay time tD2 | Grouped OUTn on or off to next group on or off, TA = +25°C | typ 2 ns | 5 |
| Output on-time error (1) tON_ERR | Output on or off latch data = all '1', 50-ns BLANK GND level pulse, VCC = 3.3 V, TA = +25°C | min -45 · max 45 ns | 5 |
Ordering codes, by the datasheet
5- TLC59283DBQR
- SSOP-24 and QSOP-24 · Tape and Reel, 2500 · p. 2
- TLC59283DBQ
- SSOP-24 and QSOP-24 · Tube, 50 · p. 2
- TLC59283RGER
- QFN-24 · Tape and Reel, 3000 · p. 2
- TLC59283RGE
- QFN-24 · Tape and Reel, 250 · p. 2
- TLC59283RGET
- VQFN · RGE, 24 pins, package quantity 250, operating temperature -40 to 85 °C · p. 20
Open-source boards using it
7- 2 layers250 × 250 mm

- 2 layers250 × 250 mm

RocSync testing
BAL-ORX/RocSync
Millisecond-Accurate Temporal Synchronization for Heterogeneous Camera Systems
336 parts3MPL-2.0 - 2 layers14 × 1 mm

Vectorscope
shabaz123/Vectorscope_GuyFawkes
A reimplementation of the Vectorscope from https://github.com/Hack-a-Day/Vectorscope
81 parts3GPL-3.0 - 4 layers256 × 32 mm

Ledmat8x16tiledriver blade
burbschat/ledmat8x16
LTP-12188M-08 Based Two Color 8x16 LEDs in 8x8 Slots LED Matrix Display Module
136 parts1CERN-OHL-S-2.0 - 2 layers105 × 85 mm

Soundboard
chill389cc/Soundboard
Code and schematics for a macropad soundboard system for the office bullpen
53 parts - 4 layers256.9 × 96.2 mm

- 4 layers31.9 × 31.9 mm

Ledmat8x16tiledriver
burbschat/ledmat8x16
LTP-12188M-08 Based Two Color 8x16 LEDs in 8x8 Slots LED Matrix Display Module
17 parts1CERN-OHL-S-2.0
Parts like it
4TLC59282DBQ
SSOP-24-150mil-40℃~+85℃ 16 17V 2% 35MHz 3V~5.5V 45mA Built-in SSOP-24-150mil LED Drivers ROHSTexas InstrumentsLED DriversTLC59284DBQ
SSOP-24-150mil-40℃~+85℃ 10V 16 35MHz 3V~5.5V 4% 45mA Buck Built-in SSOP-24-150mil LED Drivers ROHSTexas InstrumentsLED DriversTLC5948ADBQ
SSOP-24-150mil-40℃~+85℃ 10V 16 2% 33MHz 3V~5.5V 60mA Built-in Over-Temperature Protection (OTP) PWM SSOP-24-150mil LED Drivers ROHSTexas InstrumentsLED DriversAS1113-BSSU
SSOP-24-150mil-40℃~+85℃ 0V~15V 16 3% 30MHz~50MHz 3V~5.5V 50mA PWM SSOP-24-150mil LED Drivers ROHSAdvanced Monolithic SystemsLED Drivers
Questions
Is there a KiCad symbol and footprint for the TLC59283DBQ?
Yes. The symbol is 4ms-ic:TLC59283DBQR and the footprint EasyEDA_Cloud:SSOP-24_L8.7-W3.9-P0.64-LS6.0-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TLC59283DBQ?
SSOP-24-150mil, with 24 pins. Its footprint is drawn on this page.
Where is the TLC59283DBQ datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TLC59283DBQ?
JLCPCB lists it as part C702075, with 648 in stock; the sellers' links on this page open their listings.
What can replace the TLC59283DBQ?
Parts like it in the library: the TLC59282DBQ by Texas Instruments, the TLC59284DBQ by Texas Instruments, the TLC5948ADBQ by Texas Instruments and the AS1113-BSSU by Advanced Monolithic Systems. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TLC59283DBQ?
7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.