THVD2450VDRC
Texas InstrumentsExtended
-40℃~+125℃ 1 1 256 3V~5.5V 5.3mA 50Mbps Half-Duplex Transceiver ±15kV VSON-10(3x3) RS-485 / RS-422 ICs ROHS
- Part id
- ti/THVD2450VDRC
- Category
- RS 485, RS 422 ICs
- Package
- VSON-10(3x3)
- Pins
- 11
- In stock
- 247 at JLCPCB (C5960705)
Overview
The THVD2450VDRC is a RS 485, RS 422 IC made by Texas Instruments in a VSON-10(3x3) package with 11 pins. -40℃~+125℃ 1 1 256 3V~5.5V 5.3mA 50Mbps Half-Duplex Transceiver ±15kV VSON-10(3x3) RS-485 / RS-422 ICs ROHS.
PCBKit's library has its footprint (EasyEDA_Cloud:VSON-10_L3.0-W3.0-P0.50-TL-EP, from EasyEDA), ready for a KiCad board. 247 are in stock at JLCPCB (part C5960705).
Symbol
The library has no symbol for this part yet.
Footprint
From the datasheet
15- Supply, least
- 3 V · VCC, recommended operating min · p. 6
- Supply, most
- 5.5 V · VCC, recommended operating max · p. 6
- Supply, least
- 1.65 V · VIO, recommended operating min · p. 6
- Supply, absolute maximum
- 6.5 V · VCC, absolute max · p. 5
- Works from
- -40 °C · Operating ambient temperature min · p. 6
- Works up to
- 125 °C · Operating ambient temperature max · p. 6
- Junction, hottest
- 150 °C · Recommended junction temperature max · p. 6
- Takes working
- 1.804 mA · sum of VCC and VIO typical receiver-enabled quiescent currents; VCC = 5 V, VIO = 3.3 V, SLR = GND, no load · p. 9
- Takes asleep
- 200 nA · sum of VCC and VIO typical disabled quiescent currents; VCC = 5 V, VIO = 3.3 V, SLR = GND, no load · p. 9
- A pin gives at most
- 24 mA · Receiver output source or sink current absolute max · p. 5
- Data rate, most
- 50 Mbit/s · Signaling rate max, SLR = GND or floating · p. 6
- Junction to air (DRC)
- 46.7 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to case (DRC)
- 47.7 K/W · Junction-to-case top thermal resistance · p. 6
- Junction to board (DRC)
- 19.1 K/W · Junction-to-board thermal resistance · p. 6
- Edge
- 1.5 ns · typical receiver output rise/fall time, CL = 15 pF · p. 12
What it is and has
13- Interface
- Half-duplex RS-485 / RS-422 · p. 1
- Logic interface supply
- 1.65 V to 5.5 V · p. 1
- Bus fault protection
- ±70-V DC · p. 1
- HBM ESD protection
- ±16 kV · p. 1
- Fast transient burst protection
- ±4-kV IEC 61000-4-4 · p. 1
- Operational common-mode range
- ±25 V · p. 1
- Receiver noise immunity
- Enhanced receiver hysteresis · p. 1
- Hot plug-in
- Glitch-free power-up/down · p. 1
- Receiver failsafe
- Open, short, and idle bus · p. 1
- Protection
- Thermal shutdown · p. 1
- Package
- 10-pin DRC VSON · p. 3
- Logic interface supply voltage
- 1.65 V to 5.5 V · p. 1
- Bus fault protection
- ±70 V · p. 19
Around it
2- res ≥ 50 Ω
- between Logic input signal and D / DE / SLR / RE; Series resistor on each logic input recommended for optimised IEC ESD performance to minimize transient currents. · p. 5
- cap 100-nF to 220-nF
- between VCC and GND; Ceramic; place as close as possible to the supply pin. · p. 28
Specifications
117| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Logic supply voltage VIO | Over operating free-air temperature range; maximum = VCC + 0.2 V | min -0.5 V | 5 |
| Bus supply voltage VCC | Over operating free-air temperature range | min -0.5 · max 6.5 V | 5 |
| Bus voltage | Range at any bus pin as differential or common-mode with respect to GND | min -70 · max 70 V | 5 |
| Input voltage | Range at any logic pin (D, DE, SLR or RE); maximum = VIO + 0.2 V | min -0.3 V | 5 |
| Receiver output current IO | Over operating free-air temperature range | min -24 · max 24 mA | 5 |
| Storage temperature Tstg | min -65 · max 170 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; bus terminals and GND; ±16,000 V | min -16000 · max 16000 V | 5 |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; all pins except bus terminals and GND; ±4,000 V | min -4000 · max 4000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1,500 V | min -1500 · max 1500 V | 5 |
| Electrostatic discharge, Half duplex devices THVD2410V/2450V V(ESD) | THVD2450V; contact discharge, per IEC 61000-4-2; bus terminals and GND; ±15,000 V | min -15000 · max 15000 V | 5 |
| Electrostatic discharge, Half duplex devices THVD2410V/2450V V(ESD) | THVD2450V; air-gap discharge, per IEC 61000-4-2; bus terminals and GND; ±15,000 V | min -15000 · max 15000 V | 5 |
| Electrical fast transient V(EFT) | Per IEC 61000-4-4; bus terminals; ±4,000 V | min -4000 · max 4000 V | 5 |
| Supply voltage VCC | Over operating free-air temperature range | min 3 · max 5.5 V | 6 |
| I/O supply voltage VIO | Maximum = VCC | min 1.65 V | 6 |
| Input voltage at any bus terminal (separately or common mode) VI | min -25 · max 25 V | 6 | |
| Low-level input voltage (driver, driver enable, receiver enable and slew rate select inputs) VIL | Maximum = 0.3*VIO | min 0 V | 6 |
| Differential input voltage bus pins VID | min -25 · max 25 V | 6 | |
| Output current, driver IO | min -60 · max 60 mA | 6 | |
| Output current, receiver IOR | VIO = 1.8 V or 2.5 V | min -4 · max 4 mA | 6 |
| Output current, receiver IOR | VIO = 3.3 V or 5 V | min -8 · max 8 mA | 6 |
| Differential load resistance RL | 60 Ω is the nominal value | min 54 · typ 60 Ω | 6 |
| Signaling rate 1/tUI | THVD2450V with SLR = VIO | max 20 Mbps | 6 |
| Signaling rate 1/tUI | THVD2450V with SLR = GND or floating | max 50 Mbps | 6 |
| Operating ambient temperature TA | min -40 · max 125 °C | 6 | |
| Junction temperature TJ | min -40 · max 150 °C | 6 | |
| Junction-to-ambient thermal resistance RθJA | THVD2450V; DRC (VSON), 10 PINS | typ 46.7 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | THVD2450V; DRC (VSON), 10 PINS | typ 47.7 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | THVD2450V; DRC (VSON), 10 PINS | typ 19.1 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | THVD2450V; DRC (VSON), 10 PINS | typ 0.7 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | THVD2450V; DRC (VSON), 10 PINS | typ 19.1 °C/W | 6 |
| Junction-to-case (bottom) thermal resistance RθJC(bot) | THVD2450V; DRC (VSON), 10 PINS | typ 4.6 °C/W | 6 |
| Driver differential output voltage magnitude |VOD| | RL = 60 Ω, –25 V ≤ Vtest ≤ 25 V; Figure 7-1 | min 1.5 · typ 3.3 V | 8 |
| Driver differential output voltage magnitude |VOD| | RL = 60 Ω, –25 V ≤ Vtest ≤ 25 V, 4.5 V ≤ VCC ≤ 5.5 V; Figure 7-1 | min 2.1 · typ 3.3 V | 8 |
| Driver differential output voltage magnitude |VOD| | RL = 100 Ω; Figure 7-2 | min 2 · typ 4 V | 8 |
| Driver differential output voltage magnitude |VOD| | RL = 54 Ω; Figure 7-2 | min 1.5 · typ 3.5 V | 8 |
| Change in differential output voltage Δ|VOD| | RL = 54 Ω or 100 Ω; Figure 7-2 | min -50 · max 50 mV | 8 |
| Common-mode output voltage VOC | RL = 54 Ω or 100 Ω; Figure 7-2; typical = VCC/2 | min 1 · max 3 V | 8 |
| Change in steady-state common-mode output voltage ΔVOC(SS) | RL = 54 Ω or 100 Ω; Figure 7-2 | min -50 · max 50 mV | 8 |
| Short-circuit output current IOS | THVD2450V; DE = VIO, -70 V ≤ (VA or VB) ≤ 70 V, or A shorted to B | min -250 · max 250 mA | 8 |
| Bus input current II | DE = 0 V, VCC and VIO = 0 V or 5.5 V; VI = 12 V | typ 90 · max 125 uA | 8 |
| Bus input current II | DE = 0 V, VCC and VIO = 0 V or 5.5 V; VI = 25 V | typ 200 · max 250 uA | 8 |
| Bus input current II | DE = 0 V, VCC and VIO = 0 V or 5.5 V; VI = –7 V | min -100 · typ -80 uA | 8 |
| Bus input current II | DE = 0 V, VCC and VIO = 0 V or 5.5 V; VI = –25 V | min -350 · typ -220 uA | 8 |
| Positive-going input threshold voltage VTH+ | Over common-mode range of ± 25 V | min 40 · typ 125 · max 200 mV | 8 |
| Negative-going input threshold voltage VTH- | Over common-mode range of ± 25 V | min -200 · typ -125 · max -40 mV | 8 |
| Input hysteresis VHYS | Over common-mode range of ± 25 V | typ 250 mV | 8 |
| Input fail-safe threshold VTH_FSH | Over common-mode range of ± 25 V | min -40 · max 40 mV | 8 |
| Input differential capacitance CA,B | Measured between A and B, f = 1 MHz | typ 50 pF | 8 |
| Output low voltage VOL | IOL = 8 mA, VIO = 3 to 3.6 V or 4.5 V to 5.5 V | typ 0.2 · max 0.4 V | 8 |
| Output low voltage VOL | IOL = 4 mA, VIO = 1.65 to 1.95 V or 2.25 V to 2.75 V | typ 0.2 · max 0.4 V | 8 |
| Output high-impedance current, R pin IOZ | VO = 0 V or VIO, RE = VIO | min -1 · max 1 uA | 8 |
| Input current (DE , SLR) IIN | 1.65 V ≤ VIO ≤ 5.5 V, 0 V ≤ VIN ≤ VIO | max 5 uA | 8 |
| Input current (D, RE) IIN | 1.65 V ≤ VIO ≤ 5.5 V, 0 V ≤ VIN ≤ VIO | min -5 uA | 8 |
| Thermal shutdown threshold TSHDN | Temperature rising | min 150 · typ 180 °C | 8 |
| Thermal shutdown hysteresis THYS | typ 10 °C | 8 | |
| Rising under-voltage threshold on VCC UVVCC (rising) | typ 2.3 · max 2.6 V | 8 | |
| Falling under-voltage threshold on VCC UVVCC (falling) | min 1.95 · typ 2.2 V | 8 | |
| Hysteresis on under-voltage of VCC UVVCC(hys) | typ 170 mV | 8 | |
| Rising under-voltage threshold on VIO UVVIO (rising) | typ 1.4 · max 1.6 V | 8 | |
| Falling under-voltage threshold on VIO UVVIO (falling) | min 1.2 · typ 1.3 V | 8 | |
| Hysteresis on under-voltage of VIO UVVIO(hys) | typ 120 mV | 9 | |
| Supply current (quiescent), VCC = 4.5 V to 5.5 V ICC | Driver and receiver enabled; RE = 0 V, DE = VIO, No load | typ 3.5 · max 5.3 mA | 9 |
| Supply current (quiescent), VCC = 4.5 V to 5.5 V ICC | Driver enabled, receiver disabled; RE = VIO, DE = VIO, No load | typ 2.5 · max 4.2 mA | 9 |
| Supply current (quiescent), VCC = 4.5 V to 5.5 V ICC | Driver disabled, receiver enabled; RE = 0 V, DE = 0 V, No load | typ 1.8 · max 2.4 mA | 9 |
| Supply current (quiescent), VCC = 4.5 V to 5.5 V ICC | Driver and receiver disabled; RE = VIO, DE = 0 V, D = open, No load | typ 0.1 · max 1.2 uA | 9 |
| Supply current (quiescent), VCC = 3 V to 3.6 V ICC | Driver and receiver enabled; RE = 0 V, DE = VIO, No load | typ 3 · max 4.1 mA | 9 |
| Supply current (quiescent), VCC = 3 V to 3.6 V ICC | Driver enabled, receiver disabled; RE = VIO, DE = VIO, No load | typ 2 · max 3 mA | 9 |
| Supply current (quiescent), VCC = 3 V to 3.6 V ICC | Driver disabled, receiver enabled; RE = 0 V, DE = 0 V, No load | typ 1.6 · max 2.2 mA | 9 |
| Supply current (quiescent), VCC = 3 V to 3.6 V ICC | Driver and receiver disabled; RE = VIO, DE = 0 V, D = open, No load | typ 0.1 · max 1 uA | 9 |
| Logic supply current (quiescent), VIO = 3 to 3.6 V IIO | Driver disabled, Receiver enabled, SLR = GND; DE = 0 V, RE = 0 V, No load | typ 4.5 · max 8.4 uA | 9 |
| Logic supply current (quiescent), VIO = 3 to 3.6 V IIO | Driver disabled, Receiver enabled, SLR = VIO; DE = 0 V, RE = 0 V, No load | typ 3.3 · max 8.4 uA | 9 |
| Logic supply current (quiescent), VIO = 3 to 3.6 V IIO | Driver disabled, Receiver disabled, SLR = GND; DE = 0 V, RE = VIO, No load | typ 0.1 · max 1 uA | 9 |
| Logic supply current (quiescent), VIO = 3 to 3.6 V IIO | Driver disabled, Receiver disabled, SLR = VIO; DE = 0 V, RE = VIO, No load | typ 1.8 · max 4 uA | 9 |
| Differential output rise/fall time tr, tf | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 3 to 3.6 V, typical at 3.3 V | min 4 · typ 8 · max 15 ns | 12 |
| Differential output rise/fall time tr, tf | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 4.5 to 5.5 V, typical at 5 V | min 4 · typ 7 · max 15 ns | 12 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 3 to 3.6 V, typical at 3.3 V; Figure 7-3 | min 6 · typ 12 · max 30 ns | 12 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 4.5 to 5.5 V, typical at 5 V; Figure 7-3 | min 4 · typ 9 · max 26 ns | 12 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 3 to 3.6 V, typical at 3.3 V | typ 1 · max 3 ns | 12 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Driver; THVD2450V; SLR = VIO; RL = 54 Ω, CL = 50 pF; VCC = 4.5 to 5.5 V, typical at 5 V | typ 1 · max 3 ns | 12 |
| Disable time tPHZ, tPLZ | Driver; THVD2450V; SLR = VIO; RE = X; Figures 7-4 and 7-5 | typ 17 · max 35 ns | 12 |
| Enable time tPZH, tPZL | Driver; THVD2450V; SLR = VIO; RE = 0 V; Figures 7-4 and 7-5 | typ 14 · max 39 ns | 12 |
| Enable time tPZH, tPZL | Driver; THVD2450V; SLR = VIO; RE = VIO; Figures 7-4 and 7-5 | typ 3 · max 4.5 us | 12 |
| Time to shutdown tSHDN | Driver; THVD2450V; SLR = VIO; RE = VIO | min 50 · max 500 ns | 12 |
| Output rise/fall time tr, tf | Receiver; THVD2450V; SLR = VIO; CL = 15 pF | typ 1.5 · max 6 ns | 12 |
| Propagation delay tPHL, tPLH | Receiver; THVD2450V; SLR = VIO; VIO = 3 V to 3.6 V; Figure 7-6 | min 25 · typ 33 · max 58 ns | 12 |
| Propagation delay tPHL, tPLH | Receiver; THVD2450V; SLR = VIO; VIO = 1.65 V to 1.95 V; Figure 7-6 | min 25 · typ 35 · max 60 ns | 12 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Receiver; THVD2450V; SLR = VIO; CL = 15 pF | typ 0.5 · max 5 ns | 12 |
| Disable time tPHZ, tPLZ | Receiver; THVD2450V; SLR = VIO; DE = X; Figure 7-7 | typ 12 · max 25 ns | 12 |
| Enable time tPZH(1), tPZL(1) | Receiver; THVD2450V; SLR = VIO; DE = VIO; Figure 7-7 | typ 50 · max 82 ns | 12 |
| Enable time tPZH(2), tPZL(2) | Receiver; THVD2450V; SLR = VIO; DE = 0 V; Figure 7-8 | typ 2.8 · max 5 us | 12 |
| Delay to enter fail-safe operation tD(OFS) | Receiver; THVD2450V; SLR = VIO; CL = 15 pF; Figure 7-9 | min 7 · typ 10 · max 18 us | 12 |
| Delay to exit fail-safe operation tD(FSO) | Receiver; THVD2450V; SLR = VIO; CL = 15 pF; Figure 7-9 | min 19 · typ 32 · max 50 ns | 12 |
| Time to shutdown tSHDN | Receiver; THVD2450V; SLR = VIO; DE = 0 V; Figure 7-8 | min 50 · max 500 ns | 12 |
| Differential output rise/fall time tr, tf | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VCC = 3 to 3.6 V, typical at 3.3 V | min 1 · typ 5 · max 7 ns | 13 |
| Differential output rise/fall time tr, tf | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VCC = 4.5 to 5.5 V, typical at 5 V | min 1 · typ 5 · max 6 ns | 13 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VIO = 3 V to 3.6 V; VCC = 3 to 3.6 V, typical at 3.3 V; Figure 7-3 | min 5 · typ 11 · max 19 ns | 13 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VIO = 1.65 V to 1.95 V; VCC = 3 to 3.6 V, typical at 3.3 V; Figure 7-3 | min 7 · typ 12 · max 22 ns | 13 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VIO = 3 V to 3.6 V; VCC = 4.5 to 5.5 V, typical at 5 V; Figure 7-3 | min 4 · typ 8 · max 15 ns | 13 |
| Propagation delay tPHL, tPLH | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VIO = 1.65 V to 1.95 V; VCC = 4.5 to 5.5 V, typical at 5 V; Figure 7-3 | min 6 · typ 10 · max 19 ns | 13 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VCC = 3 to 3.6 V, typical at 3.3 V | typ 1 · max 3 ns | 13 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Driver; THVD2450V; SLR = 0; RL = 54 Ω, CL = 50 pF; VCC = 4.5 to 5.5 V, typical at 5 V | typ 1 · max 3 ns | 13 |
| Disable time tPHZ, tPLZ | Driver; THVD2450V; SLR = 0; RE = X; Figures 7-4 and 7-5 | typ 14 · max 30 ns | 13 |
| Enable time tPZH, tPZL | Driver; THVD2450V; SLR = 0; RE = 0 V; VIO = 1.65 V to 1.95 V, 2.25 V to 2.75 V; Figures 7-4 and 7-5 | typ 20 · max 35 ns | 13 |
| Enable time tPZH, tPZL | Driver; THVD2450V; SLR = 0; RE = 0 V; VIO = 3 V to VCC V; Figures 7-4 and 7-5 | typ 15 · max 32 ns | 13 |
| Enable time tPZH, tPZL | Driver; THVD2450V; SLR = 0; RE = VIO; Figures 7-4 and 7-5 | typ 2.5 · max 4.5 us | 13 |
| Time to shutdown tSHDN | Driver; THVD2450V; SLR = 0; RE = VIO | min 50 · max 500 ns | 13 |
| Output rise/fall time tr, tf | Receiver; THVD2450V; SLR = 0; CL = 15 pF; Figure 7-6 | typ 1.5 · max 6 ns | 13 |
| Propagation delay tPHL, tPLH | Receiver; THVD2450V; SLR = 0; CL = 15 pF; VIO = 3 V to 3.6 V; Figure 7-6 | min 25 · typ 33 · max 58 ns | 13 |
| Propagation delay tPHL, tPLH | Receiver; THVD2450V; SLR = 0; CL = 15 pF; VIO = 1.65 V to 1.95 V; Figure 7-6 | min 25 · typ 35 · max 60 ns | 13 |
| Pulse skew, |tPHL – tPLH| tSK(P) | Receiver; THVD2450V; SLR = 0; CL = 15 pF; Figure 7-6 | typ 0.5 · max 5 ns | 13 |
| Disable time tPHZ, tPLZ | Receiver; THVD2450V; SLR = 0; DE = X | typ 12 · max 25 ns | 13 |
| Enable time tPZH(1), tPZL(1) | Receiver; THVD2450V; SLR = 0; DE = VIO; VIO = 1.65 V to 1.95 V; Figure 7-7 | typ 50 · max 82 ns | 13 |
| Enable time tPZH(1), tPZL(1) | Receiver; THVD2450V; SLR = 0; DE = VIO; VIO = 3 V to 3.6 V; Figure 7-7 | typ 50 · max 75 ns | 13 |
| Enable time tPZH(2), tPZL(2) | Receiver; THVD2450V; SLR = 0; DE = 0 V; Figure 7-8 | typ 2.8 · max 5 us | 13 |
| Delay to enter fail-safe operation tD(OFS) | Receiver; THVD2450V; SLR = 0; CL = 15 pF; Figure 7-9 | min 7 · typ 10 · max 18 us | 13 |
| Delay to exit fail-safe operation tD(FSO) | Receiver; THVD2450V; SLR = 0; CL = 15 pF; Figure 7-9 | min 19 · typ 32 · max 50 ns | 13 |
| Time to shutdown tSHDN | Receiver; THVD2450V; SLR = 0; DE = 0 V; Figure 7-8 | min 50 · max 500 ns | 13 |
Pins, by the datasheet
11- 1 VIO
- Supply for logic I/O signals R, RE, D, DE, and SLR. · p. 3
- 2 R
- Receive data output. · p. 3
- 3 DE
- Driver enable input; integrated pull-down. · p. 3
- 4 RE
- Receiver enable input; integrated pull-up. · p. 3
- 5 D
- Transmission data input; integrated pull-up. · p. 3
- 6 GND
- Local device ground. · p. 3
- 7 SLR
- Slew rate select: Low = 50 Mbps, High = 20 Mbps; defaults to 50 Mbps if left floating. · p. 3
- 8 A
- RS 485 bus I/O, A. · p. 3
- 9 B
- RS 485 bus I/O, B. · p. 3
- 10 VCC
- Bus supply. · p. 3
- Thermal Pad Thermal Pad
- Connect to GND for optimal thermal performance. · p. 3
Ordering codes, by the datasheet
1- THVD2450VDRCR
- VSON · DRC drawing, 10 pins, package quantity 5000, operating temperature -40 to 125 °C, marking 2450 · p. 30
Parts like it
3THVD2419DRC
VSON-10-EP(3x3)VSON-10-EP(3x3) RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsSN65HVD01DRCT
VSON-10-EP(3x3)-40℃~+125℃ 1 1 20Mbps 256 3V~3.6V 750uA Enable shutdown、Thermal shutdown protection、Tx/Rx enable、Fail-safe Half-Duplex Transceiver ±15kV VSON-10-EP(3x3) RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsTHVD2442DRC
VSON-10-EP(3x3)-40℃~+125℃ 1 1 20Mbps 256 3V~5.5V 7uA Full-Duplex Transceiver ±8kV VSON-10-EP(3x3) RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICs
Questions
Is there a KiCad symbol and footprint for the THVD2450VDRC?
Yes. the footprint EasyEDA_Cloud:VSON-10_L3.0-W3.0-P0.50-TL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the THVD2450VDRC?
VSON-10(3x3), with 11 pins. Its footprint is drawn on this page.
Where is the THVD2450VDRC datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the THVD2450VDRC?
JLCPCB lists it as part C5960705, with 247 in stock; the sellers' links on this page open their listings.
What can replace the THVD2450VDRC?
Parts like it in the library: the THVD2419DRC by Texas Instruments, the SN65HVD01DRCT by Texas Instruments and the THVD2442DRC by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.