Skip to the content
9

THVD2450DRB

Texas InstrumentsExtended

-40℃~+125℃ 1 1 256 3V~5.5V 5.6mA 50Mbps Half-Duplex Transceiver ±16kV SON-8-EP(3x3) RS-485 / RS-422 ICs ROHS

Part id
ti/THVD2450DRB
Category
RS 485, RS 422 ICs
Package
SON-8-EP(3x3)
Pins
9
In stock
4,832 at JLCPCB (C2878080)
Used on
7 open-source boards

Overview

The THVD2450DRB is a RS 485, RS 422 IC made by Texas Instruments in a SON-8-EP(3x3) package with 9 pins. -40℃~+125℃ 1 1 256 3V~5.5V 5.6mA 50Mbps Half-Duplex Transceiver ±16kV SON-8-EP(3x3) RS-485 / RS-422 ICs ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:ST4E1240IQT, from EasyEDA) and its footprint (EasyEDA_Cloud:SON-8_L3.0-W3.0-P0.65-TL-EP, from EasyEDA), ready for a KiCad board. 4,832 are in stock at JLCPCB (part C2878080). 7 open-source boards in 4 repositories on GitHub use it.

Symbol

9EP8VCC5GND3DE2RE#1R4D6A7B
EasyEDA_Cloud:ST4E1240IQTFrom EasyEDA

Footprint

9
EasyEDA_Cloud:SON-8_L3.0-W3.0-P0.65-TL-EPFrom EasyEDA

From the datasheet

14
Supply, least
3 V · VCC, recommended operating min · p. 5
Supply, most
5.5 V · VCC, recommended operating max · p. 5
Supply, absolute maximum
7 V · VCC, absolute max · p. 4
Works from
-40 °C · Operating ambient temperature min · p. 5
Works up to
125 °C · Operating ambient temperature max · p. 5
Junction, hottest
150 °C · Junction temperature max · p. 5
Takes working
3.5 mA · VCC, driver and receiver enabled, no load, typical · p. 6
Takes asleep
100 nA · VCC, driver and receiver disabled, no load, typical · p. 6
A pin gives at most
24 mA · Receiver output current, absolute max magnitude · p. 4
Junction to air (DRB)
47.6 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (DRB)
49.4 K/W · Junction-to-case top thermal resistance · p. 5
Junction to board (DRB)
20.3 K/W · Junction-to-board thermal resistance · p. 5
Data rate, most
50 Mbit/s · THVD2450 signaling rate max · p. 5
Edge
2 ns · Receiver output rise/fall time, typical · p. 7

What it is and has

14
Interface
Half-duplex RS-422/RS-485 transceiver · p. 1
Functional safety
Functional Safety-Capable · p. 1
Signaling rate
50 Mbps · p. 1
Bus fault protection
±70-V DC · p. 1
HBM ESD protection
±16 kV · p. 1
IEC ESD contact discharge protection
±12 kV, IEC 61000-4-2 · p. 1
IEC ESD air-gap discharge protection
±12 kV, IEC 61000-4-2 · p. 1
Fast transient burst protection
±4 kV, IEC 61000-4-4 · p. 1
Hot plug-in capability
Glitch-free power-up/down · p. 1
Failsafe
Open, short, and idle bus · p. 1
Protection
Thermal shutdown · p. 1
Bus loading
1/8 unit load, up to 256 bus nodes · p. 1
Bus fault protection
±70 V · p. 12
Receiver hysteresis
250 mV typical · p. 12

Around it

2
cap 100-nF to 220-nF
between VCC and GND; Place as close as possible to the transceiver VCC pin. · p. 21
res 1-kΩ to 10-kΩ
between enable lines and VCC or GND; Pull-up and pull-down resistors to limit noise currents during transient events. · p. 21

Specifications

74
ParameterConditionsAs printedPage
Supply voltage VCCOver operating free-air temperature rangemin -0.5 · max 7 V4
Bus voltageRange at any bus pin (A or B) as differential or common-mode with respect to GNDmin -70 · max 70 V4
Input voltageRange at any logic pin (D, DE, or RE)min -0.3 · max 5.7 V4
Receiver output current IOOver operating free-air temperature rangemin -24 · max 24 mA4
Storage temperature Tstgmin -65 · max 170 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; bus terminals and GND; ±16,000 Vmin -16000 · max 16000 V4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; all pins except bus terminals and GND; ±8,000 Vmin -8000 · max 8000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per ANSI/ESDA/JEDEC JS-002; ±1,500 Vmin -1500 · max 1500 V4
Electrostatic discharge V(ESD)Contact discharge, per IEC 61000-4-2; bus terminals and GND; ±12,000 Vmin -12000 · max 12000 V4
Electrostatic discharge V(ESD)Air-gap discharge, per IEC 61000-4-2; bus terminals and GND; ±12,000 Vmin -12000 · max 12000 V4
Electrical fast transient V(EFT)Per IEC 61000-4-4; bus terminals; ±4,000 Vmin -4000 · max 4000 V4
Supply voltage VCCOver operating free-air temperature rangemin 3 · max 5.5 V5
Input voltage at any bus terminal (separately or common mode)(1) VIOver operating free-air temperature rangemin -25 · max 25 V5
High-level input voltage (driver, driver enable, and receiver enable inputs) VIHmin 2 V5
Low-level input voltage (driver, driver enable, and receiver enable inputs) VILmax 0.8 V5
Differential input voltage VIDmin -25 · max 25 V5
Output current, driver IOmin -60 · max 60 mA5
Output current, receiver IORmin -8 · max 8 mA5
Differential load resistance RLNOM = 60 Ωmin 54 · typ 60 Ω5
Signaling rate 1/tUITHVD2450max 50 Mbps5
Operating ambient temperature TAmin -40 · max 125 °C5
Junction temperature TJmin -40 · max 150 °C5
Junction-to-ambient thermal resistance RθJATHVD2450, DRB (VSON), 8 PINStyp 47.6 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)THVD2450, DRB (VSON), 8 PINStyp 49.4 °C/W5
Junction-to-board thermal resistance RθJBTHVD2450, DRB (VSON), 8 PINStyp 20.3 °C/W5
Junction-to-top characterization parameter ψJTTHVD2450, DRB (VSON), 8 PINStyp 0.9 °C/W5
Junction-to-board characterization parameter ψJBTHVD2450, DRB (VSON), 8 PINStyp 20.2 °C/W5
Junction-to-case (bottom) thermal resistance RθJC(bot)THVD2450, DRB (VSON), 8 PINStyp 5.6 °C/W5
Driver and receiver enabled, VCC = 5.5 V, TA = 125 °C, random data (PRBS7) at signaling rate PDTHVD2450; 50 Mbps; unterminated; RL = 300 Ω, CL = 50 pF (driver); VALUE columntyp 340 mW5
Driver and receiver enabled, VCC = 5.5 V, TA = 125 °C, random data (PRBS7) at signaling rate PDTHVD2450; 50 Mbps; RS-422 load; RL = 100 Ω, CL = 50 pF (driver); VALUE columntyp 340 mW5
Driver and receiver enabled, VCC = 5.5 V, TA = 125 °C, random data (PRBS7) at signaling rate PDTHVD2450; 50 Mbps; RS-485 load; RL = 54 Ω, CL = 50 pF (driver); VALUE columntyp 370 mW5
Driver differential output voltage magnitude |VOD|RL = 60 Ω, –25 V ≤ Vtest ≤ 25 V (See Figure 7-1)min 1.5 · typ 3.3 V6
Driver differential output voltage magnitude |VOD|RL = 60 Ω, –25 V ≤ Vtest ≤ 25 V, 4.5 V ≤ VCC ≤ 5.5 V (See Figure 7-1)min 2.1 · typ 3.3 V6
Driver differential output voltage magnitude |VOD|RL = 100 Ω (See Figure 7-2)min 2 · typ 4 V6
Driver differential output voltage magnitude |VOD|RL = 54 Ω (See Figure 7-2)min 1.5 · typ 3.3 V6
Change in differential output voltage Δ|VOD|RL = 54 Ω or 100 Ω (See Figure 7-2)min -50 · max 50 mV6
Common-mode output voltage VOCRL = 54 Ω or 100 Ω (See Figure 7-2); typical = VCC/2min 1 · max 3 V6
Change in steady-state common-mode output voltage ΔVOC(SS)RL = 54 Ω or 100 Ω (See Figure 7-2)min -50 · max 50 mV6
Short-circuit output current IOSDE = VCC, -70 V ≤ (VA or VB) ≤ 70 Vmin -250 · max 250 mA6
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = 12 Vtyp 75 · max 125 uA6
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = 25 Vtyp 150 · max 250 uA6
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = –7 Vmin -100 · typ -40 uA6
Bus input current IIDE = 0 V, VCC = 0 V or 5.5 V, VI = –25 Vmin -250 · typ -150 uA6
Positive-going input threshold voltage(1) VTH+Over common-mode range of ± 25 Vmin 40 · typ 125 · max 200 mV6
Negative-going input threshold voltage(1) VTH-Over common-mode range of ± 25 Vmin -200 · typ -125 · max -40 mV6
Input hysteresis VHYSOver common-mode range of ± 25 Vtyp 250 mV6
Input fail-safe threshold VTH_FSHmin -40 · max 40 mV6
Input differential capacitance CA,BMeasured between A and B, f = 1 MHztyp 50 pF6
Output low voltage VOLIOL = 8 mAtyp 0.2 · max 0.4 V6
Output high-impedance current IOZVO = 0 V or VCC, RE = VCCmin -1 · max 1 uA6
Input current (DE) IIN3 V ≤ VCC ≤ 5.5 V, 0 V ≤ VIN ≤ VCCmax 5 uA6
Input current (D, RE) IIN3 V ≤ VCC ≤ 5.5 V, 0 V ≤ VIN ≤ VCCmin -5 uA6
Thermal shutdown threshold TSHDNTemperature risingmin 150 · typ 170 °C6
Thermal shutdown hysteresis THYStyp 10 °C6
Supply current (quiescent) ICCDriver and receiver enabled; RE = 0 V, DE = VCC, No loadtyp 3.5 · max 5.6 mA6
Supply current (quiescent) ICCDriver enabled, receiver disabled; RE = VCC, DE = VCC, No loadtyp 2.5 · max 4.4 mA6
Supply current (quiescent) ICCDriver disabled, receiver enabled; RE = 0 V, DE = 0 V, No loadtyp 1.8 · max 2.4 mA6
Supply current (quiescent) ICCDriver and receiver disabled; RE = VCC, DE = 0 V, D = open, No loadtyp 0.1 · max 1 uA6
Differential output rise/fall time tr, tfDriver; RL = 54 Ω, CL = 50 pF; See Figure 7-3typ 5 · max 7 ns7
Propagation delay tPHL, tPLHDriver; RL = 54 Ω, CL = 50 pF; See Figure 7-3min 5 · typ 10 · max 16 ns7
Pulse skew, |tPHL – tPLH| tSK(P)Driver; RL = 54 Ω, CL = 50 pF; See Figure 7-3max 3.5 ns7
Disable time tPHZ, tPLZDriver; See Figure 7-4 and Figure 7-5typ 11 · max 30 ns7
Enable time tPZH, tPZLDriver; RE = 0 V; See Figure 7-4 and Figure 7-5typ 8 · max 25 ns7
Enable time tPZH, tPZLDriver; RE = VCC; See Figure 7-4 and Figure 7-5typ 1.5 · max 4 us7
Time to shutdown tSHDNDriver; RE = VCCmin 50 · max 500 ns7
Output rise/fall time tr, tfReceiver; CL = 15 pF; See Figure 7-6typ 2 · max 6 ns7
Propagation delay tPHL, tPLHReceiver; CL = 15 pF; See Figure 7-6typ 40 · max 55 ns7
Pulse skew, |tPHL – tPLH| tSK(P)Receiver; CL = 15 pF; See Figure 7-6max 4 ns7
Disable time tPHZ, tPLZReceiver; See Figure 7-7typ 7 · max 15 ns7
Enable time tPZH(1), tPZL(1)Receiver; DE = VCC; See Figure 7-7typ 50 · max 70 ns7
Enable time tPZH(2), tPZL(2)Receiver; DE = 0 V; See Figure 7-8typ 2 · max 4 us7
Delay to enter fail-safe operation tD(OFS)Receiver; CL = 15 pF; See Figure 7-9min 7 · typ 10 · max 18 us7
Delay to exit fail-safe operation tD(FSO)Receiver; CL = 15 pF; See Figure 7-9min 25 · typ 35 · max 50 ns7
Time to shutdown tSHDNReceiver; DE = 0 V; See Figure 7-8min 50 · max 500 ns7

Pins, by the datasheet

8
1 R
Receive data output. · p. 3
2 RE
Receiver enable, active low, with 2-MΩ internal pull-up. · p. 3
3 DE
Driver enable, active high, with 2-MΩ internal pull-down. · p. 3
4 D
Driver data input. · p. 3
5 GND
Device ground. · p. 3
6 A
Bus I/O port, A (complementary to B). · p. 3
7 B
Bus I/O port, B (complementary to A). · p. 3
8 VCC
3.3-V to 5-V supply. · p. 3

Open-source boards using it

7
  • 2 layers22 × 53.5 mmIsolated RS485 Bridge, the printed circuit board in 3D

    Isolated RS485 Bridge

    Anderman/tombask

    All message send Slave can send after a poll frame. Slave is ready sending when the last padding byte is 0x55 To write byte 0x08 must be 0x02

    22 parts
  • 2 layers149 × 141 mmFurnace Controller, the printed circuit board in 3D

    Furnace Controller

    veskotr/furnace-pcb

    The main PCB for the furnace project

    99 parts
  • 4 layers49.2 × 58.9 mmTemp transmitter pcb, the printed circuit board in 3D

    Temp transmitter pcb

    veskotr/temp-transmitter

    Temp Transmitter is a small STM32 bare-metal firmware project for a Modbus RTU temperature-transmitter node. It is currently a pilot application for the HSS STM32 framework: the application code lives in this…

    63 parts
  • 4 layers94 × 74 mmHigh speed, the printed circuit board in 3D

    High speed

    marmbrus/circuits

    94 parts
  • 4 layers73 × 12 mmReceiver, the printed circuit board in 3D

    Receiver

    marmbrus/circuits

    26 parts

Parts like it

3

Questions

Is there a KiCad symbol and footprint for the THVD2450DRB?

Yes. The symbol is EasyEDA_Cloud:ST4E1240IQT and the footprint EasyEDA_Cloud:SON-8_L3.0-W3.0-P0.65-TL-EP, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the THVD2450DRB?

SON-8-EP(3x3), with 9 pins. Its footprint is drawn on this page.

Where is the THVD2450DRB datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the THVD2450DRB?

JLCPCB lists it as part C2878080, with 4,832 in stock; the sellers' links on this page open their listings.

What can replace the THVD2450DRB?

Parts like it in the library: the SN65HVD78DRBR by Texas Instruments, the THVD1451DRBT by Texas Instruments and the SN55HVD75DRBREP by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the THVD2450DRB?

7 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.