TCAN3414DDF
Texas InstrumentsExtended
-40℃~+150℃ 1 17uA 3.3V 55mA 8Mbps CAN FD Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection TSOT-23-8 CAN Transceivers ROHS
- Part id
- ti/TCAN3414DDF
- Category
- CAN Transceivers
- Package
- TSOT-23-8
- Pins
- 8
- In stock
- 0 at JLCPCB (C24836183)
Overview
The TCAN3414DDF is a CAN Transceiver made by Texas Instruments in a TSOT-23-8 package with 8 pins. -40℃~+150℃ 1 17uA 3.3V 55mA 8Mbps CAN FD Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection TSOT-23-8 CAN Transceivers ROHS.
PCBKit's library has its footprint (Package_TO_SOT_SMD:TSOT-23-8, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C24836183).
Symbol
The library has no symbol for this part yet.
Footprint
From the datasheet
12- Supply, least
- 3 V · VCC, recommended operating min · p. 4
- Supply, most
- 3.6 V · VCC, recommended operating max · p. 4
- Supply, absolute maximum
- 6 V · VCC, absolute max · p. 4
- Junction, hottest
- 165 °C · Junction temperature absolute max · p. 4
- A pin gives at most
- 8 mA · RXD source or sink absolute max · p. 4
- Takes working
- 42 mA · VCC normal mode dominant typical, RL = 60 Ω · p. 5
- Takes at most
- 60 mA · VCC normal mode dominant max, RL = 50 Ω · p. 5
- Junction to air (DDF (SOT))
- 122.9 K/W · Junction-to-ambient thermal resistance · p. 4
- Junction to case (DDF (SOT))
- 51.7 K/W · Junction-to-case top thermal resistance · p. 4
- Junction to board (DDF (SOT))
- 45.7 K/W · Junction-to-board thermal resistance · p. 4
- Data rate, most
- 8 Mbit/s · CAN FD networks, max · p. 16
- Edge
- 10 ns · RXD output rise time, typical; STB, SHDN = 0 V, CL(RXD) = 15 pF · p. 10
What it is and has
12- Supply
- 3.3 V single supply operation · p. 1
- Receiver common mode input voltage
- ±30 V · p. 1
- Bus fault protection
- ±58 V · p. 1
- IEC ESD protection on bus pins
- ±10 kV · p. 1
- Protection
- TXD-dominant time-out (DTO) · p. 1
- Protection
- Thermal-shutdown protection (TSD) · p. 1
- Supply
- 3.3 V single supply · p. 1
- Shutdown mode
- Ultra-low power; most internal blocks disabled · p. 16
- Standby wake-up
- CAN bus wake-up indicated through RXD · p. 21
- Protection
- CAN bus short-circuit current limiting · p. 19
- Protection
- Undervoltage detection · p. 20
- Protection
- Thermal shutdown with hysteresis · p. 20
Specifications
106| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | min -0.3 · max 6 V | 4 | |
| CAN bus I/O voltage range on CANH and CANL VBUS | min -58 · max 58 V | 4 | |
| Max differential voltage between CANH and CANL VDIFF | VDIFF = (CANH - CANL) | min -58 · max 58 V | 4 |
| Logic pin input voltage (TXD, STB, SHDN) VLogic_Input | min -0.3 · max 6 V | 4 | |
| Logic output voltage range (RXD) VRXD | min -0.3 · max 6 V | 4 | |
| RXD output current IO(RXD) | min -8 · max 8 mA | 4 | |
| Junction temperature TJ | min -40 · max 165 °C | 4 | |
| Storage temperature TSTG | min -65 · max 150 °C | 4 | |
| Electrostatic discharge VESD | Human-body model (HBM), HBM classification level 3A for all pins; value ±4000 V | max 4000 V | 4 |
| Electrostatic discharge VESD | Human-body model (HBM), HBM classification level 3B for global pins CANH and CANL with respect to GND; value ±10000 V | max 10000 V | 4 |
| Electrostatic discharge VESD | Charged-device model (CDM), CDM classification level C5 for all pins; value ±750 V | max 750 V | 4 |
| System level electrostatic discharge VESD | CAN bus terminals (CANH, CANL) to GND, IEC61000-4-2; value ±10000 V | max 10000 V | 4 |
| Supply voltage VCC | 3.3 V nominal | min 3 · max 3.6 V | 4 |
| RXD terminal high-level output current IOH(RXD) | TCAN3414 | min -2 mA | 4 |
| RXD terminal low-level output current IOL(RXD) | TCAN3414 | max 2 mA | 4 |
| Junction temperature TJ | min -40 · max 150 °C | 4 | |
| Junction-to-ambient thermal resistance RΘJA | DDF (SOT), TCAN3413/3414 | typ 122.9 ℃/W | 4 |
| Junction-to-case (top) thermal resistance RΘJC(top) | DDF (SOT), TCAN3413/3414 | typ 51.7 ℃/W | 4 |
| Junction-to-board thermal resistance RΘJB | DDF (SOT), TCAN3413/3414 | typ 45.7 ℃/W | 4 |
| Junction-to-top characterization parameter ΨJT | DDF (SOT), TCAN3413/3414 | typ 1.3 ℃/W | 5 |
| Junction-to-board characterization parameter ΨJB | DDF (SOT), TCAN3413/3414 | typ 45.4 ℃/W | 5 |
| Supply current normal mode ICC | Dominant; TXD = 0 V, STB = 0 V, RL = 60 Ω, CL = open; See Figure 6-1 | typ 42 · max 55 mA | 5 |
| Supply current normal mode ICC | Dominant; TXD = 0 V, STB = 0 V, RL = 50 Ω, CL = open; See Figure 6-1 | typ 50 · max 60 mA | 5 |
| Supply current normal mode ICC | Recessive; TXD = VCC, STB = 0 V, RL = 50 Ω, CL = open; See Figure 6-1 | typ 7 · max 8.2 mA | 5 |
| Supply current normal mode ICC | Dominant with bus fault; TXD = 0 V, STB = 0 V, CANH = CANL = ±25 V, RL = open, CL = open; See Figure 6-1 | max 130 mA | 5 |
| Supply current standby mode (TCAN3414) ICC | TXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 85 °C; See Figure 6-1 | typ 10 · max 15 uA | 5 |
| Supply current standby mode (TCAN3414) ICC | TXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 125 °C; See Figure 6-1 | typ 10 · max 16 uA | 5 |
| Supply current standby mode (TCAN3414) ICC | TXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 150 °C; See Figure 6-1 | typ 10 · max 17 uA | 5 |
| Undervoltage detection VCC rising UVCC(R) | Ramp up | typ 2.75 · max 2.9 V | 5 |
| Undervoltage detection on VCC falling UVCC(F) | Ramp down | min 2.5 · typ 2.65 V | 5 |
| Hysteresis voltage on UVCC VHYS(UVCC) | typ 120 mV | 6 | |
| Average power dissipation Normal mode PD | VCC = 3.3 V, TJ = 27°C, RL = 60Ω, CL_RXD = 15 pF; TXD input = 250 kHz 50% duty cycle square wave | typ 50 mW | 6 |
| Average power dissipation Normal mode PD | VCC = 3.6 V, TJ = 150°C, RL = 50Ω, CL_RXD = 15 pF; TXD input = 2.5 MHz 50% duty cycle square wave | typ 60 mW | 6 |
| Thermal shutdown temperature TTSD | typ 192 °C | 6 | |
| Thermal shutdown hysteresis TTSD_HYS | typ 10 °C | 6 | |
| Dominant output voltage normal mode VO(DOM) | CANH; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open; See Figure 6-2 and Figure 7-3; maximum = VCC | min 2.25 V | 6 |
| Dominant output voltage normal mode VO(DOM) | CANL; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min 0.5 · max 1.25 V | 6 |
| Recessive output voltage normal mode VO(REC) | CANH and CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open (no load), CL = open; See Figure 6-2 and Figure 7-3 | min 1.5 · typ 1.9 · max 2.25 V | 6 |
| Driver symmetry {(VO(CANH) + VO(CANL))/(VO(REC_CANH) + VO(REC_CANL)} VSYM | TXD = 250 kHz, 1 MHz, 2.5 MHz, STB, SHDN = 0 V; RL = 60, CSPLIT = 4.7 nF, CL = open; See Figure 6-2 and Figure 8-2 | min 0.9 · max 1.1 V/V | 6 |
| DC output symmetry (CANHREC + CANLREC - CANHDOM - CANLDOM) VSYM_DC | STB, SHDN = 0 V; RL = 60 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min -400 · max 400 mV | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB. SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min 1.5 · max 3 V | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; 45 Ω ≤ RL ≤ 70 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min 1.4 · max 3 V | 6 |
| Differential output voltage normal mode Dominant VOD(DOM) | CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; RL = 2240 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min 1.5 · max 3.4 V | 6 |
| Differential output voltage normal mode Recessive VOD(REC) | CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = 60 Ω, CL = open; See Figure 6-2 and Figure 7-3 | min -120 · max 12 mV | 6 |
| Differential output voltage normal mode Recessive VOD(REC) | CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open, CL = open; See Figure 6-2 and Figure 7-3 | min -50 · max 50 mV | 6 |
| Bus output voltage standby mode VO(STB) | CANH; TXD = STB = VIO or VCC, RL = open, CL = open; See Figure 6-2 and Figure 7-3 | min -0.1 · max 0.1 V | 7 |
| Bus output voltage standby mode VO(STB) | CANL; TXD = STB = VIO or VCC, RL = open, CL = open; See Figure 6-2 and Figure 7-3 | min -0.1 · max 0.1 V | 7 |
| Bus output voltage standby mode VO(STB) | CANH - CANL; TXD = STB = VIO or VCC, RL = open, CL = open; See Figure 6-2 and Figure 7-3 | min -0.2 · max 0.2 V | 7 |
| Short-circuit bus output current, dominant, normal mode IOS(DOM) | See Figure 6-7 and Figure 7-3, V(CANH) = -15 V to 40 V, CANL = open, TXD = 0 V | min -115 · max 115 mA | 7 |
| Short-circuit bus output current, dominant, normal mode IOS(DOM) | See Figure 6-7 and Figure 7-3, V(CAN_L) = -15 V to 40 V, CANH = open, TXD = 0 V | min -115 · max 115 mA | 7 |
| Short-circuit steady-state output current, recessive, normal mode IOS(REC) | See Figure 6-7 and Figure 7-3, V(CANH) = -27 V to 32 V, CANL = open, STB=0, TXD = VIO or VCC | min -7 · max 7 mA | 7 |
| Short-circuit steady-state output current, recessive, normal mode IOS(REC) | See Figure 6-7 and Figure 7-3, V(CANL) = -27 V to 32 V, CANH = open, STB = 0, TXD = VIO or VCC | min -7 · max 7 mA | 7 |
| Input threshold voltage normal mode VIT | See Figure 6-3 and Table 7-6; -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min 500 · max 900 mV | 7 |
| Input threshold standby mode, TCAN3414 VIT(STB) | See Figure 6-3 and Table 7-6; -30 V ≤ VCM ≤ 30 V, SHDN= 0 V, STB= VCC | min 400 · max 1150 mV | 7 |
| Normal mode dominant state differential input voltage range VDOM | See Figure 6-3 and Table 7-6; -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min 0.9 · max 9 V | 7 |
| Normal mode recessive state differential input voltage range VREC | See Figure 6-3 and Table 7-6; -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | min -4 · max 0.5 V | 7 |
| Standby mode dominant state differential input voltage range VDOM(STB) | See Figure 6-3 and Table 7-6; SHDN= 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 V | min 1.15 · max 9 V | 7 |
| Standby mode recessive state differential input voltage range VREC(STB) | See Figure 6-3 and Table 7-6; SHDN = 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 V | min -4 · max 0.4 V | 7 |
| Hysteresis voltage for input threshold normal mode VHYS | See Figure 6-3 and Table 7-6; -30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 V | typ 50 mV | 7 |
| Common mode range normal and standby modes VCM | See Figure 6-3 and Table 7-6 | min -30 · max 30 V | 7 |
| Unpowered bus input leakage current ILKG(IOFF) | CANH = CANL = 5 V, VCC = VIO = GND | max 5 uA | 7 |
| Input capacitance to ground (CANH or CANL) CI | TXD = VIO | max 40 pF | 7 |
| Differential input capacitance CID | TXD = VIO | max 20 pF | 7 |
| Differential input resistance RID | TXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 V | min 25 · max 50 kΩ | 7 |
| Single ended input resistance (CANH or CANL) RIN | TXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 V | min 13 · max 25 kΩ | 7 |
| Input resistance matching [1 – (RIN(CANH) / RIN(CANL))] × 100 % RIN(M) | V(CAN_H) = V(CAN_L) = 5 V | min -3 · max 3 % | 7 |
| High-level input leakage current IIH | TXD = VCC = VIO = 3.6 V | min -2.5 · typ 0 · max 1 uA | 7 |
| Low-level input leakage current IIL | TXD = 0 V, VCC = VIO = 3.6 V | min -200 · typ -100 · max -20 uA | 7 |
| Unpowered leakage current ILKG(OFF) | TXD = 3.6 V, VCC = VIO = 0 V | min -1 · typ 0 · max 1 uA | 7 |
| Input capacitance CI | typ 4 pF | 8 | |
| Unpowered leakage current ILKG(OFF) | RXD = 3.6 V, VCC = VIO = 0 V | min -1 · typ 0 · max 1 uA | 8 |
| High-level input leakage current IIH | VCC = VIO = STB = 3.6 V | min -2 · max 2 uA | 8 |
| Low-level input leakage current IIL | VCC = VIO = 3.6 V, STB = 0 V | min -20 · max -2 uA | 8 |
| Unpowered leakage current ILKG(OFF) | STB = 3.6V, VCC= VIO = 0 V | min -1 · typ 0 · max 1 uA | 8 |
| High-level input leakage current IIH | VCC = VIO = SHDN = 3.6 V | min 2 · max 5.5 uA | 8 |
| Low-level input leakage current IIL | VCC = VIO = 3.6 V, SHDN = 0 V | min -2 · max 2 uA | 8 |
| Unpowered leakage current ILKG(OFF) | SHDN = 3.6 V, VCC= VIO = 0 V | min -1 · typ 0 · max 1 uA | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant tPROP(LOOP1) | TCAN3414; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 95 · max 180 ns | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), dominant to recessive tPROP(LOOP2) | TCAN3414; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | typ 120 · max 180 ns | 8 |
| Mode change time, from normal to standby or from standby to normal tMODE | See Figure 6-5 | max 30 us | 9 |
| Mode change time from normal mode to shutdown mode tSHDN1 | With TXD = High, Time from SHDN pin (low to high edge 50%) to CANH going from recessive level Vo(rec) to 0.5V | max 40 us | 9 |
| Mode change time from shutdown mode to normal mode tSHDN2 | With TXD high, time from SHDN pin (high to low edge 50%) to CANH going from 0.5V to Vo(rec) | max 200 us | 9 |
| Filter time for a valid wake-up pattern tWK_FILTER | See Figure 7-5 | min 0.5 · max 1.8 us | 9 |
| Bus wake-up timeout value tWK_TIMEOUT | See Figure 7-5 | min 0.8 · max 6 ms | 9 |
| Time duration after VCC or VIO hass cleared UV+, and device can resume normal operation Tstartup | max 1.5 ms | 9 | |
| Filter on STB pin to filter out any glitches Tfilter(STB) | min 0.5 · typ 1 · max 2 us | 9 | |
| Filter on SHDN pin to filter out any glitches Tfilter(SHDN) | min 0.5 · typ 1 · max 2 us | 9 | |
| Propagation delay time, low-to-high TXD edge to driver recessive (dominant to recessive) tprop(TxD-busrec) | TCAN3414; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 V | typ 65 · max 100 ns | 9 |
| Propagation delay time, high-to-low TXD edge to driver dominant (recessive to dominant) tprop(TxD-busdom) | TCAN3414; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 V | typ 46 · max 100 ns | 9 |
| Pulse skew (|tprop(TxD-busrec) - tprop(TxD-busdom)|) tsk(p) | STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, See Figure 6-2 | typ 18 · max 28 ns | 9 |
| Differential output signal rise time tR | See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | typ 32 · max 57 ns | 9 |
| Differential output signal fall time tF | See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | typ 30 · max 50 ns | 9 |
| Dominant timeout tTXD_DTO | See Figure 6-6, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF | min 1.2 · max 4 ms | 9 |
| Propagation delay time, bus recessive input to RXD high output (dominant to recessive) tprop(busrec-RXD) | TCAN3414; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 V | typ 55 · max 90 ns | 9 |
| Propagation delay time, bus dominant input to RXD low output (recessive to dominant) tprop(busdom-RXD) | TCAN3414; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 V | typ 45 · max 90 ns | 10 |
| RXD output signal rise time tR | See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF | typ 10 · max 25 ns | 10 |
| RXD output signal fall time tF | See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF | typ 10 · max 28 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 500 ns tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 450 · max 525 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 200 ns tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 160 · max 205 ns | 10 |
| Bit time on CAN bus output pins with tBIT(TXD) = 125 ns(1) tBIT(BUS) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterization | min 85 · max 130 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 500 ns tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 410 · max 540 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 200 ns tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF | min 130 · max 210 ns | 10 |
| Bit time on RXD output pins with tBIT(TXD) = 125 ns(1) tBIT(RXD) | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterization | min 75 · max 135 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 500 ns ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS) | min -50 · max 20 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 200 ns ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS) | min -40 · max 10 ns | 10 |
| Receiver timing symmetry with tBIT(TXD) = 125 ns(1) ΔtREC | See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS); Min/Max limits based on characterization | min -40 · max 10 ns | 10 |
Pins, by the datasheet
8- 1 TXD
- CAN transmit data input; integrated pull-up. · p. 3
- 2 GND
- Ground connection. · p. 3
- 3 VCC
- 3.3 V supply voltage. · p. 3
- 4 RXD
- CAN receive data output, tri-stated when device powered off. · p. 3
- 5 SHDN
- High selects ultra-low power shutdown mode; integrated pull-down. · p. 3
- 6 CANL
- Low-level CAN bus input/output line. · p. 3
- 7 CANH
- High-level CAN bus input/output line. · p. 3
- 8 STB
- Standby input for mode control; integrated pull-up. · p. 3
Parts like it
8MAX3051EKA+T
SOT-23-8-40℃~+85℃ 15uA 1Mbps 3.3V 70mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSMaxim Integrated (Analog Devices)CAN TransceiversTCAN332GDCN
SOT-23-8-40℃~+125℃ 20uA 3V~3.6V 5Mbps 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN330GDCN
SOT-23-8-40℃~+125℃ 1 2.5uA 3V~3.6V 55mA 5Mbps CAN FD Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Silent mode SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN334GDCN
SOT-23-8-40℃~+125℃ 20uA 3.3V 55mA 5Mbps CAN FD Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN337GDCN
SOT-23-8-40℃~+125℃ 20uA 3V~3.6V 5Mbps 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN1044VDDFRQ1
TSOT-23-8-40℃~+125℃ 1 1uA 4.5V~5.5V 70mA 8Mbps CAN FD Transceiver TSOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN1044AVDDFRQ1
TSOT-23-8-40℃~+150℃ 1.5uA 4.5V~5.5V 5Mbps 70mA CAN FD Transceiver TSOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN330DCN
SOT-23-8-40℃~+125℃ 1 1Mbps 2.5mA 3V~3.6V 60mA CAN Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Short-Circuit Protection、Silent mode SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
Questions
Is there a KiCad symbol and footprint for the TCAN3414DDF?
Yes. the footprint Package_TO_SOT_SMD:TSOT-23-8, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TCAN3414DDF?
TSOT-23-8, with 8 pins. Its footprint is drawn on this page.
Where is the TCAN3414DDF datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TCAN3414DDF?
JLCPCB lists it as part C24836183, with 0 in stock; the sellers' links on this page open their listings.
What can replace the TCAN3414DDF?
Parts like it in the library: the MAX3051EKA+T by Maxim Integrated (Analog Devices), the TCAN332GDCN by Texas Instruments, the TCAN330GDCN by Texas Instruments and the TCAN334GDCN by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.