Skip to the content
12345678

TCAN3414D

Texas InstrumentsExtended

-40℃~+125℃ 1 17uA 3V~3.6V 42mA 5Mbps CAN FD Transceiver SOIC-8 CAN Transceivers ROHS

Part id
ti/TCAN3414D
Category
CAN Transceivers
Package
SOIC-8
Pins
8
In stock
6,065 at JLCPCB (C22396693)
Used on
12 open-source boards

Overview

The TCAN3414D is a CAN Transceiver made by Texas Instruments in a SOIC-8 package with 8 pins. -40℃~+125℃ 1 17uA 3V~3.6V 42mA 5Mbps CAN FD Transceiver SOIC-8 CAN Transceivers ROHS.

PCBKit's library has its KiCad symbol (TCAN3414DR:TCAN3414DR, from Antmicro) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 6,065 are in stock at JLCPCB (part C22396693). 12 open-source boards in 6 repositories on GitHub use it.

Symbol

1TXD2GND3VCC4RXD5SHDN6CAN_L7CAN_H8STB
TCAN3414DR:TCAN3414DRFrom Antmicro

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

13
Supply, least
3 V · VCC, recommended operating min · p. 4
Supply, most
3.6 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
6 V · VCC, absolute maximum · p. 4
Junction, hottest
165 °C · Junction temperature, absolute maximum · p. 4
A pin gives at most
8 mA · RXD output current, absolute maximum source or sink · p. 4
Takes working
50 mA · VCC normal mode dominant, RL = 50 Ω, typical · p. 5
Takes at most
60 mA · VCC normal mode dominant, RL = 50 Ω, max · p. 5
Takes asleep
10 µA · VCC standby mode, TJ <= 125 °C, typical · p. 5
Junction to air (D (SOIC))
114.4 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (D (SOIC))
49 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (D (SOIC))
58 K/W · Junction-to-board thermal resistance · p. 4
Data rate, most
8 Mbit/s · CAN FD networks, max · p. 16
Edge
10 ns · RXD output rise time, typical; CL(RXD) = 15 pF · p. 10

What it is and has

11
Supply
3.3 V single supply · p. 1
Bus fault protection
±58 V · p. 1
Bus pin IEC ESD protection
±10 kV · p. 1
Protection
Undervoltage protection · p. 1
Protection
TXD-dominant time-out (DTO) · p. 1
Protection
Thermal-shutdown protection (TSD) · p. 1
Supply
3.3 V single supply operation · p. 1
Shutdown mode
Ultra-low power shutdown · p. 16
Protection
CAN bus short-circuit current limiting · p. 19
Protection
Thermal shutdown · p. 19
Wake-up
Remote wake-up request via CAN bus in standby mode · p. 21

Specifications

106
ParameterConditionsAs printedPage
Supply voltage VCCmin -0.3 · max 6 V4
CAN bus I/O voltage range on CANH and CANL VBUSmin -58 · max 58 V4
Max differential voltage between CANH and CANL VDIFFVDIFF = (CANH - CANL)min -58 · max 58 V4
Logic pin input voltage (TXD, STB, SHDN) VLogic_Inputmin -0.3 · max 6 V4
Logic output voltage range (RXD) VRXDmin -0.3 · max 6 V4
RXD output current IO(RXD)min -8 · max 8 mA4
Junction temperature TJmin -40 · max 165 °C4
Storage temperature TSTGmin -65 · max 150 °C4
Electrostatic discharge VESDHuman-body model (HBM), HBM classification level 3A for all pins; ±4000 Vmax 4000 V4
Electrostatic discharge VESDHuman-body model (HBM), HBM classification level 3B for global pins CANH and CANL with respect to GND; ±10000 Vmax 10000 V4
Electrostatic discharge VESDCharged-device model (CDM), CDM classification level C5 for all pins; ±750 Vmax 750 V4
System level electrostatic discharge VESDCAN bus terminals (CANH, CANL) to GND, IEC61000-4-2; ±10000 Vmax 10000 V4
Supply voltage VCCNominal 3.3 Vmin 3 · typ 3.3 · max 3.6 V4
RXD terminal high-level output current IOH(RXD)TCAN3414min -2 mA4
RXD terminal low-level output current IOL(RXD)TCAN3414max 2 mA4
Junction temperature TJmin -40 · max 150 °C4
Junction-to-ambient thermal resistance RΘJAD (SOIC)typ 114.4 ℃/W4
Junction-to-case (top) thermal resistance RΘJC(top)D (SOIC)typ 49 ℃/W4
Junction-to-board thermal resistance RΘJBD (SOIC)typ 58 ℃/W4
Junction-to-top characterization parameter ΨJTD (SOIC)typ 7 ℃/W5
Junction-to-board characterization parameter ΨJBD (SOIC)typ 57.1 ℃/W5
Supply current normal mode ICCDominant; TXD = 0 V, STB = 0 V, RL = 60 Ω, CL = opentyp 42 · max 55 mA5
Supply current normal mode ICCDominant; TXD = 0 V, STB = 0 V, RL = 50 Ω, CL = opentyp 50 · max 60 mA5
Supply current normal mode ICCRecessive; TXD = VCC, STB = 0 V, RL = 50 Ω, CL = opentyp 7 · max 8.2 mA5
Supply current normal mode ICCDominant with bus fault; TXD = 0 V, STB = 0 V, CANH = CANL = ±25 V, RL = open, CL = openmax 130 mA5
Supply current standby mode (TCAN3414) ICCTXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 85 °Ctyp 10 · max 15 uA5
Supply current standby mode (TCAN3414) ICCTXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 125 °Ctyp 10 · max 16 uA5
Supply current standby mode (TCAN3414) ICCTXD = STB = VCC, RL = 50 Ω, CL = open, TJ <= 150 °Ctyp 10 · max 17 uA5
Undervoltage detection VCC rising UVCC(R)Ramp uptyp 2.75 · max 2.9 V5
Undervoltage detection on VCC falling UVCC(F)Ramp downmin 2.5 · typ 2.65 V5
Hysteresis voltage on UVCC VHYS(UVCC)typ 120 mV6
Average power dissipation Normal mode PDVCC = 3.3 V, TJ = 27°C, RL = 60Ω, CL_RXD = 15 pF; TXD input = 250 kHz 50% duty cycle square wavetyp 50 mW6
Average power dissipation Normal mode PDVCC = 3.6 V, TJ = 150°C, RL = 50Ω, CL_RXD = 15 pF; TXD input = 2.5 MHz 50% duty cycle square wavetyp 60 mW6
Thermal shutdown temperature TTSDtyp 192 °C6
Thermal shutdown hysteresis TTSD_HYStyp 10 °C6
Dominant output voltage normal mode VO(DOM)CANH; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = open; maximum VCCmin 2.25 V6
Dominant output voltage normal mode VO(DOM)CANL; TXD = 0 V, STB, SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = openmin 0.5 · max 1.25 V6
Recessive output voltage normal mode VO(REC)CANH and CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open (no load), CL = openmin 1.5 · typ 1.9 · max 2.25 V6
Driver symmetry {(VO(CANH) + VO(CANL))/(VO(REC_CANH) + VO(REC_CANL)} VSYMTXD = 250 kHz, 1 MHz, 2.5 MHz, STB, SHDN = 0 V; RL = 60, CSPLIT = 4.7 nF, CL = openmin 0.9 · max 1.1 V/V6
DC output symmetry (CANHREC + CANLREC - CANHDOM - CANLDOM) VSYM_DCSTB, SHDN = 0 V; RL = 60 Ω, CL = openmin -400 · max 400 mV6
Differential output voltage normal mode Dominant VOD(DOM)CANH - CANL; TXD = 0 V, STB. SHDN = 0 V; 50 Ω ≤ RL ≤ 65 Ω, CL = openmin 1.5 · max 3 V6
Differential output voltage normal mode Dominant VOD(DOM)CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; 45 Ω ≤ RL ≤ 70 Ω, CL = openmin 1.4 · max 3 V6
Differential output voltage normal mode Dominant VOD(DOM)CANH - CANL; TXD = 0 V, STB, SHDN = 0 V; RL = 2240 Ω, CL = openmin 1.5 · max 3.4 V6
Differential output voltage normal mode Recessive VOD(REC)CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = 60 Ω, CL = openmin -120 · max 12 mV6
Differential output voltage normal mode Recessive VOD(REC)CANH - CANL; TXD = VIO or VCC, STB, SHDN = 0 V; RL = open, CL = openmin -50 · max 50 mV6
Bus output voltage standby mode VO(STB)CANH; TXD = STB = VIO or VCC, RL = open, CL = openmin -0.1 · max 0.1 V7
Bus output voltage standby mode VO(STB)CANL; TXD = STB = VIO or VCC, RL = open, CL = openmin -0.1 · max 0.1 V7
Bus output voltage standby mode VO(STB)CANH - CANL; TXD = STB = VIO or VCC, RL = open, CL = openmin -0.2 · max 0.2 V7
Short-circuit bus output current, dominant, normal mode IOS(DOM)V(CANH) = -15 V to 40 V, CANL = open, TXD = 0 Vmin -115 · max 115 mA7
Short-circuit bus output current, dominant, normal mode IOS(DOM)V(CAN_L) = -15 V to 40 V, CANH = open, TXD = 0 Vmin -115 · max 115 mA7
Short-circuit steady-state output current, recessive, normal mode IOS(REC)V(CANH) = -27 V to 32 V, CANL = open, STB=0, TXD = VIO or VCCmin -7 · max 7 mA7
Short-circuit steady-state output current, recessive, normal mode IOS(REC)V(CANL) = -27 V to 32 V, CANH = open, STB = 0, TXD = VIO or VCCmin -7 · max 7 mA7
Input threshold voltage normal mode VIT-30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 Vmin 500 · max 900 mV7
Input threshold standby mode, TCAN3414 VIT(STB)-30 V ≤ VCM ≤ 30 V, SHDN= 0 V, STB= VCCmin 400 · max 1150 mV7
Normal mode dominant state differential input voltage range VDOM-30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 Vmin 0.9 · max 9 V7
Normal mode recessive state differential input voltage range VREC-30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 Vmin -4 · max 0.5 V7
Standby mode dominant state differential input voltage range VDOM(STB)SHDN= 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 Vmin 1.15 · max 9 V7
Standby mode recessive state differential input voltage range VREC(STB)SHDN = 0 V, STB = VIO, -30 V ≤ VCM ≤ 30 Vmin -4 · max 0.4 V7
Hysteresis voltage for input threshold normal mode VHYS-30 V ≤ VCM ≤ 30 V, STB, SHDN= 0 Vtyp 50 mV7
Common mode range normal and standby modes VCMSee Figure 6-3 and Table 7-6min -30 · max 30 V7
Unpowered bus input leakage current ILKG(IOFF)CANH = CANL = 5 V, VCC = VIO = GNDmax 5 uA7
Input capacitance to ground (CANH or CANL) CITXD = VIOmax 40 pF7
Differential input capacitance CIDTXD = VIOmax 20 pF7
Differential input resistance RIDTXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 Vmin 25 · max 50 kΩ7
Single ended input resistance (CANH or CANL) RINTXD = VIO, STB = 0 V -30 V ≤ VCM ≤ 30 Vmin 13 · max 25 kΩ7
Input resistance matching [1 – (RIN(CANH) / RIN(CANL))] × 100 % RIN(M)V(CAN_H) = V(CAN_L) = 5 Vmin -3 · max 3 %7
High-level input leakage current IIHTXD = VCC = VIO = 3.6 Vmin -2.5 · typ 0 · max 1 uA7
Low-level input leakage current IILTXD = 0 V, VCC = VIO = 3.6 Vmin -200 · typ -100 · max -20 uA7
Unpowered leakage current ILKG(OFF)TXD = 3.6 V, VCC = VIO = 0 Vmin -1 · typ 0 · max 1 uA7
Input capacitance CItyp 4 pF8
Unpowered leakage current ILKG(OFF)RXD Terminal; RXD = 3.6 V, VCC = VIO = 0 Vmin -1 · typ 0 · max 1 uA8
High-level input leakage current IIHSTB Terminal; VCC = VIO = STB = 3.6 Vmin -2 · max 2 uA8
Low-level input leakage current IILSTB Terminal; VCC = VIO = 3.6 V, STB = 0 Vmin -20 · max -2 uA8
Unpowered leakage current ILKG(OFF)STB Terminal; STB = 3.6V, VCC= VIO = 0 Vmin -1 · typ 0 · max 1 uA8
High-level input leakage current IIHSHDN Terminal; VCC = VIO = SHDN = 3.6 Vmin 2 · max 5.5 uA8
Low-level input leakage current IILSHDN Terminal; VCC = VIO = 3.6 V, SHDN = 0 Vmin -2 · max 2 uA8
Unpowered leakage current ILKG(OFF)SHDN Terminal; SHDN = 3.6 V, VCC= VIO = 0 Vmin -1 · typ 0 · max 1 uA8
Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant tPROP(LOOP1)TCAN3414; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFtyp 95 · max 180 ns8
Total loop delay, driver input (TXD) to receiver output (RXD), dominant to recessive tPROP(LOOP2)TCAN3414; See Figure 6-4, normal mode, VCC = VIO = 3 V to 3.6 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFtyp 120 · max 180 ns8
Mode change time, from normal to standby or from standby to normal tMODESee Figure 6-5max 30 us9
Mode change time from normal mode to shutdown mode tSHDN1With TXD = High, Time from SHDN pin (low to high edge 50%) to CANH going from recessive level Vo(rec) to 0.5Vmax 40 us9
Mode change time from shutdown mode to normal mode tSHDN2With TXD high, time from SHDN pin (high to low edge 50%) to CANH going from 0.5V to Vo(rec)max 200 us9
Filter time for a valid wake-up pattern tWK_FILTERSee Figure 7-5min 0.5 · max 1.8 us9
Bus wake-up timeout value tWK_TIMEOUTSee Figure 7-5min 0.8 · max 6 ms9
Time duration after VCC or VIO hass cleared UV+, and device can resume normal operation Tstartupmax 1.5 ms9
Filter on STB pin to filter out any glitches Tfilter(STB)min 0.5 · typ 1 · max 2 us9
Filter on SHDN pin to filter out any glitches Tfilter(SHDN)min 0.5 · typ 1 · max 2 us9
Propagation delay time, low-to-high TXD edge to driver recessive (dominant to recessive) tprop(TxD-busrec)TCAN3414; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 Vtyp 65 · max 100 ns9
Propagation delay time, high-to-low TXD edge to driver dominant (recessive to dominant) tprop(TxD-busdom)TCAN3414; See Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, VCC = VIO = 3 V to 3.6 Vtyp 46 · max 100 ns9
Pulse skew (|tprop(TxD-busrec) - tprop(TxD-busdom)|) tsk(p)STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, See Figure 6-2typ 18 · max 28 ns9
Differential output signal rise time tRSee Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pFtyp 32 · max 57 ns9
Differential output signal fall time tFSee Figure 6-2, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pFtyp 30 · max 50 ns9
Dominant timeout tTXD_DTOSee Figure 6-6, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pFmin 1.2 · max 4 ms9
Propagation delay time, bus recessive input to RXD high output (dominant to recessive) tprop(busrec-RXD)TCAN3414; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 Vtyp 55 · max 90 ns9
Propagation delay time, bus dominant input to RXD low output (recessive to dominant) tprop(busdom-RXD)TCAN3414; See Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pF, VCC = VIO = 3 V to 3.6 Vtyp 45 · max 90 ns10
RXD output signal rise time tRSee Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pFtyp 10 · max 25 ns10
RXD output signal fall time tFSee Figure 6-3, STB, SHDN = 0 V, CL(RXD) = 15 pFtyp 10 · max 28 ns10
Bit time on CAN bus output pins with tBIT(TXD) = 500 ns tBIT(BUS)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFmin 450 · max 525 ns10
Bit time on CAN bus output pins with tBIT(TXD) = 200 ns tBIT(BUS)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFmin 160 · max 205 ns10
Bit time on CAN bus output pins with tBIT(TXD) = 125 ns(1) tBIT(BUS)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterizationmin 85 · max 130 ns10
Bit time on RXD output pins with tBIT(TXD) = 500 ns tBIT(RXD)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFmin 410 · max 540 ns10
Bit time on RXD output pins with tBIT(TXD) = 200 ns tBIT(RXD)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pFmin 130 · max 210 ns10
Bit time on RXD output pins with tBIT(TXD) = 125 ns(1) tBIT(RXD)See Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; Min/Max limits based on characterizationmin 75 · max 135 ns10
Receiver timing symmetry with tBIT(TXD) = 500 ns ΔtRECSee Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS)min -50 · max 20 ns10
Receiver timing symmetry with tBIT(TXD) = 200 ns ΔtRECSee Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS)min -40 · max 10 ns10
Receiver timing symmetry with tBIT(TXD) = 125 ns(1) ΔtRECSee Figure 6-4, STB, SHDN = 0 V, RL = 60 Ω, CL = 100 pF, CL(RXD) = 15 pF; ΔtREC = tBIT(RXD) - tBIT(BUS); Min/Max limits based on characterizationmin -40 · max 10 ns10

Pins, by the datasheet

8
1 TXD
CAN transmit data input; integrated pull-up. · p. 3
2 GND
Ground connection. · p. 3
3 VCC
3.3 V supply voltage. · p. 3
4 RXD
CAN receive data output, tri-stated when device powered off. · p. 3
5 SHDN
High selects ultra-low power shutdown mode; integrated pull-down. · p. 3
6 CANL
Low-level CAN bus input/output line. · p. 3
7 CANH
High-level CAN bus input/output line. · p. 3
8 STB
Standby input for mode control; integrated pull-up. · p. 3

Open-source boards using it

12See all 12
  • 8 layers50 × 50 mmOmodri laas, the printed circuit board in 3D

    Omodri laas

    open-dynamic-robot-initiative/open-motor-driver-initiative

    Open-source drive for brushless motors, following the open dynamic robot initiative

    265 parts122BSD-3-Clause
  • 4 layers80 × 80 mmEPS, the printed circuit board in 3D

    EPS

    4111Spyglass/Hardware_CSAT

    243 parts1
  • 4 layers120 × 120 mmDaq griffin, the printed circuit board in 3D

    Daq griffin

    cuspaceflight/white-giant-sensing-pcb

    This is the pcb used to read up to 12 4-20mA pressure transcievers that are used on the white giant engine

    223 partsGPL-3.0
  • 4 layers80 × 80 mmAuxio board, the printed circuit board in 3D

    Auxio board

    MatthiasGeorgImhof/Hardware_CSAT

    Hardware design files for Cubesat PCBs

    129 parts
  • 4 layers77 × 61.5 mmCAN IMU, the printed circuit board in 3D

    CAN IMU

    risingtideresearch/can-imu-pcb

    An IMU carrier PCB

    56 parts
  • 8 layers54.8 × 57.7 mmOmodri sa v2 laas, the printed circuit board in 3D

    Omodri sa v2 laas

    open-dynamic-robot-initiative/open-motor-driver-initiative

    Open-source drive for brushless motors, following the open dynamic robot initiative

    216 parts122BSD-3-Clause
  • 4 layers80 × 80 mmAux board, the printed circuit board in 3D

    Aux board

    4111Spyglass/Hardware_CSAT

    126 parts1
  • 4 layers80 × 80 mmAVIONICS BOARD, the printed circuit board in 3D

    AVIONICS BOARD

    4111Spyglass/Hardware_CSAT

    183 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCAN3414D?

Yes. The symbol is TCAN3414DR:TCAN3414DR and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCAN3414D?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the TCAN3414D datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCAN3414D?

JLCPCB lists it as part C22396693, with 6,065 in stock; the sellers' links on this page open their listings.

What can replace the TCAN3414D?

Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCAN3414D?

12 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.