TCAN337DCN
Texas InstrumentsExtended
-40℃~+125℃ 1Mbps 20uA 3V~3.6V 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHS
- Part id
- ti/TCAN337DCN
- Category
- CAN Transceivers
- Package
- SOT-23-8
- Pins
- 8
- In stock
- 28 at JLCPCB (C2671619)
Overview
The TCAN337DCN is a CAN Transceiver made by Texas Instruments in a SOT-23-8 package with 8 pins. -40℃~+125℃ 1Mbps 20uA 3V~3.6V 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHS.
PCBKit's library has its KiCad symbol (Interface_CAN_LIN:TCAN337, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-8, from KiCad's library), ready for a KiCad board. 28 are in stock at JLCPCB (part C2671619).
Symbol
Footprint
From the datasheet
14- Supply, least
- 3 V · VCC, recommended operating min · p. 5
- Supply, most
- 3.6 V · VCC, recommended operating max · p. 5
- Supply, absolute maximum
- 5 V · VCC, absolute max · p. 5
- Works from
- -40 °C · Operational free-air temperature min · p. 5
- Works up to
- 125 °C · Operational free-air temperature max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature max · p. 5
- Takes working
- 55 mA · Normal mode dominant, typical bus load RL = 60Ω, max · p. 6
- Takes at most
- 60 mA · Normal mode dominant, high bus load RL = 50Ω, max · p. 6
- A pin gives at most
- 8 mA · Logic output current absolute max · p. 5
- Junction to air (DCN (SOT-23))
- 154.4 K/W · Junction-to-ambient thermal resistance · p. 6
- Junction to case (DCN (SOT-23))
- 76.6 K/W · Junction-to-case top thermal resistance · p. 6
- Junction to board (DCN (SOT-23))
- 49.2 K/W · Junction-to-board thermal resistance · p. 6
- Data rate, most
- 1 Mbit/s · TCAN337 data rate max · p. 3
- Edge
- 6 ns · RXD output fall time typical · p. 9
What it is and has
13- Supply
- 3.3V single supply operation · p. 1
- CAN compatibility
- ISO 11898-2 · p. 1
- Package options
- SOIC-8 and SOT-23 · p. 1
- Operating modes
- Normal mode · p. 1
- Operating modes
- Silent mode · p. 1
- Common mode range
- ±12V · p. 1
- Bus pin fault protection
- ±14V · p. 1
- Protection
- Driver dominant time out (TXD DTO) · p. 1
- Protection
- Receiver dominant time out (RXD DTO) · p. 1
- Fault output
- Fault output pin · p. 1
- Protection
- Undervoltage protection on VCC · p. 1
- Protection
- Thermal shutdown protection · p. 1
- Protection
- Current limiting on bus pins · p. 1
Specifications
82| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply Voltage range VCC | Over operating free-air temperature range | min -0.3 · max 5 V | 5 |
| Voltage at any bus terminal (CANH or CANL) V(BUS) | Over operating free-air temperature range | min -14 · max 14 V | 5 |
| Logic input terminal voltage range V(Logic_Input) | Over operating free-air temperature range | min -0.3 · max 5 V | 5 |
| Logic output terminal voltage range V(Logic_Output) | Over operating free-air temperature range | min -0.3 · max 5 V | 5 |
| Logic output current IO(LOGIC) | Over operating free-air temperature range | max 8 mA | 5 |
| Operating junction temperature range TJ | min -40 · max 150 °C | 5 | |
| Storage temperature Tstg | max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; all pins except CANH and CANL; ±4000 V | max 4000 V | 5 |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; pins CANH and CANL; ±25000 V | max 25000 V | 5 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; all pins; ±1500 V | max 1500 V | 5 |
| Electrostatic discharge V(ESD) | IEC 61400-4-2 Contact Discharge; CANH and CANL terminals to GND; ±12000 V | max 12000 V | 5 |
| Supply voltage VCC | Over operating free-air temperature range | min 3 · max 3.6 V | 5 |
| Logic terminal HIGH level output current IOH(LOGIC) | Over operating free-air temperature range | min -2 mA | 5 |
| Logic terminal LOW level output current IOL(LOGIC) | Over operating free-air temperature range | max 2 mA | 5 |
| Operational free-air temperature TA | min -40 · max 125 °C | 5 | |
| Junction-to-ambient thermal resistance RθJA | TCAN33x, DCN (SOT-23), 8 PINS | typ 154.4 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | TCAN33x, DCN (SOT-23), 8 PINS | typ 76.6 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | TCAN33x, DCN (SOT-23), 8 PINS | typ 49.2 °C/W | 6 |
| Junction-to-top characterization parameter ψJT | TCAN33x, DCN (SOT-23), 8 PINS | typ 11.9 °C/W | 6 |
| Junction-to-board characterization parameter ψJB | TCAN33x, DCN (SOT-23), 8 PINS | typ 49.2 °C/W | 6 |
| Average power dissipation PD | DCN (SOT-23); VCC = 3.3 V, TJ = 27°C, RL = 60 Ω, SHDN, S and STB at 0 V, Input to TXD at 500 kHz, 50% duty cycle square wave, CL(RXD) = 15 pF | typ 65 mW | 6 |
| Thermal shutdown temperature TSD | TCAN33x, DCN (SOT-23), 8 PINS | typ 175 °C | 6 |
| Thermal shutdown hysteresis THYS | TCAN33x, DCN (SOT-23), 8 PINS | typ 5 °C | 6 |
| Supply current Normal Mode ICC | Dominant; See Figure 6-1. TXD = 0V, RL = 60Ω, CL = open, S, STB and SHDN = 0V. Typical Bus Load. | max 55 mA | 6 |
| Supply current Normal Mode ICC | Dominant; See Figure 6-1. TXD = 0V, RL = 50Ω, CL = open, S, STB and SHDN = 0V. High Bus Load. | max 60 mA | 6 |
| Supply current Normal Mode ICC | Dominant with bus fault; See Figure 6-1. TXD = 0V, S, STB and SHDN = 0V, CANH = -12V, RL = open, CL = open | max 180 mA | 6 |
| Supply current Normal Mode ICC | Recessive; See Figure 6-1. TXD = VCC, RL = 50Ω, CL = open, S, STB and SHDN = 0V | max 3.5 mA | 6 |
| Supply Current: Silent Mode ICC | See Figure 6-1. TXD = VCC, RL = 50Ω, CL = open, S = VCC | max 2.5 mA | 6 |
| Rising under voltage detection on VCC for protected mode UV(VCC) | typ 2.2 · max 2.6 V | 6 | |
| Falling under voltage detection on VCC for protected mode UV(VCC) | min 1.65 · typ 2 · max 2.5 V | 6 | |
| Hysteresis voltage on UV(VCC) VHYS(UVVCC) | typ 200 mV | 6 | |
| Bus output voltage (dominant) VO(D) | CANH; See Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, RL = 60Ω, CL = open; maximum VCC | min 2.45 V | 6 |
| Bus output voltage (dominant) VO(D) | CANL; See Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, RL = 60Ω, CL = open | min 0.5 · max 1.25 V | 6 |
| Bus output voltage (recessive) VO(R) | See Figure 6-3 and Figure 6-2, TXD = VCC, STB, SHDN = 0V, S = 0V or VCC, RL = open (no load) | typ 1.85 V | 6 |
| Differential output voltage (dominant) VOD(D) | See Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, 50Ω ≤ RL ≤ 65Ω, CL = open | min 1.6 · max 3 V | 7 |
| Differential output voltage (dominant) VOD(D) | See Figure 6-3 and Figure 6-2, TXD = 0V, S, STB and SHDN = 0V, 45Ω ≤ RL < 50Ω, CL = open | min 1.5 · max 3 V | 7 |
| Differential output voltage (recessive) VOD(R) | See Figure 6-3 and Figure 6-2, TXD = VCC, S, STB and SHDN = 0V, RL = 60Ω, CL = open | min -120 · max 12 mV | 7 |
| Differential output voltage (recessive) VOD(R) | TA < 85°C, See Figure 6-3 and Figure 6-2, TXD = VCC, S, STB and SHDN = 0V, RL = open (no load), CL = open | min -50 · max 50 mV | 7 |
| Differential output voltage (recessive) VOD(R) | See Figure 6-3 and Figure 6-2, TXD = VCC, S, STB and SHDN = 0V, RL = open (no load), CL = open | min -50 · max 100 mV | 7 |
| Output symmetry (dominant and recessive) (CANHREC + CANLREC – CANHDOM – CANLDOM) V(SYM) | See Figure 6-3 and Figure 6-2, S, STB and SHDN = 0V, RL = 60Ω, CL = open | min -400 · max 400 mV | 7 |
| Short-circuit steady-state output current, Dominant IOS(DOM) | See Figure 6-9, V(CANH) = –12V, CANL = open, TXD = 0V | min -200 mA | 7 |
| Short-circuit steady-state output current, Dominant IOS(DOM) | See Figure 6-9, V(CANL) = 12V, CANH = open, TXD = 0V | max 200 mA | 7 |
| Short-circuit steady-state output current, Recessive IOS(REC) | See Figure 6-9, –12V ≤ VBUS ≤ 12V, VBUS = CANH = CANL, TXD = VCC | min -5 · max 5 mA | 7 |
| Input threshold voltage, normal modes and selective wake modes VIT | Receiver; See Figure 6-3 and Table 6-7 | min 500 · max 900 mV | 8 |
| Hysteresis voltage for input threshold, normal modes and selective wake modes VHYS | Receiver; See Figure 6-3 and Table 6-7 | typ 120 mV | 8 |
| Common Mode Range: normal and silent modes VCM | Receiver | min -12 · max 12 V | 8 |
| Power-off (unpowered) bus input leakage current IIOFF(LKG) | CANH = CANL = 3.3V, VCC to GND via 0Ω and 47kΩ resistor | max 12 uA | 8 |
| Input capacitance to ground (CANH or CANL) CI | Receiver | max 20 pF | 8 |
| Differential input capacitance CID | Receiver | max 10 pF | 8 |
| Differential input resistance RID | TXD = VCC, Normal Mode | min 30 · max 80 kΩ | 8 |
| Input resistance (CANH or CANL) RIN | TXD = VCC, Normal mode | min 15 · max 40 kΩ | 8 |
| Input resistance matching: [1 – (RIN(CANH) / RIN(CANL))] × 100 % RIN(M) | V(CANH) = V(CANL) | min -3 · max 3 % | 8 |
| HIGH level input voltage VIH | TXD Terminal (CAN Transmit Data Input) | min 2 V | 8 |
| LOW level input voltage VIL | TXD Terminal (CAN Transmit Data Input) | max 0.8 V | 8 |
| HIGH level input leakage current IIH | TXD = VCC = 3.6V | min -2.5 · typ 0 · max 3 uA | 8 |
| LOW level input leakage current IIL | TXD = 0V, VCC = 3.6V | min -4 · typ 0 · max 0 uA | 8 |
| Unpowered leakage current ILKG(OFF) | TXD = 3.6V, VCC = 0V | min -2 · typ 0 · max 2.5 uA | 8 |
| Input Capacitance I(CAP) | TXD Terminal (CAN Transmit Data Input) | typ 2.5 pF | 8 |
| LOW level output voltage VOL | RXD Terminal; See Figure 6-3, IO = 2mA | typ 0.2 · max 0.4 V | 8 |
| Unpowered leakage current ILKG(OFF) | RXD = 3.6V, VCC = 0V | min -1 · typ 0 · max 1 uA | 8 |
| HIGH level input voltage VIH | S terminal | min 2 V | 8 |
| LOW level input voltage VIL | S terminal | max 0.8 V | 8 |
| HIGH level input leakage current IIH | S terminal; STB, S, SHDN = VCC = 3.6V | min -3 · typ 0 · max 10 uA | 8 |
| LOW level input leakage current IIL | S terminal; STB, S, SHDN = 0V, VCC = 3.6V | min -4 · typ 0 · max 1 uA | 8 |
| Unpowered leakage current ILKG(OFF) | S terminal; STB, S, SHDN = 3.6V, VCC = 0V | min -3 · typ 0 · max 5 uA | 8 |
| Output current high level ICH | FAULT Pin (Fault Output), TCAN337 only; FAULT = VCC, See Figure 6-11 | min -10 uA | 8 |
| Output current low level ICL | FAULT Pin (Fault Output), TCAN337 only; FAULT = 0.4V, See Figure 6-11 | min 4 · typ 12 mA | 8 |
| Total loop delay, driver input (TXD) to receiver output (RXD), recessive to dominant and dominant to recessive tPROP(LOOP) | See Figure 6-6, S, STB and SHDN = 0V, RL = 60Ω, CL = 100pF, CL(RXD) = 15pF | typ 100 · max 135 ns | 9 |
| Total Loop delay in highly loaded network tPROP(LOOP) | See Figure 6-6, S, STB and SHDN = 0V, RL = 120Ω, CL = 200pF, CL(RXD) = 15pF | typ 120 · max 180 ns | 9 |
| Mode change time tMODE | See Figure 6-4 and Figure 6-5. RL = 60Ω, CL = 100pF, CL(RXD) = 15pF | typ 5 · max 10 us | 9 |
| Re-enable time after UV event tUV_RE-ENABLE | Time for device to return to normal operation from UV(VCC) under voltage event | max 1000 us | 9 |
| Propagation delay time, HIGH TXD to Driver Recessive tpHR | See Figure 6-2, S, STB and SHDN = 0V. RL = 60Ω, CL = 100pF | typ 25 ns | 9 |
| Propagation delay time, LOW TXD to Driver Dominant tpLD | See Figure 6-2, S, STB and SHDN = 0V. RL = 60Ω, CL = 100pF | typ 20 ns | 9 |
| Pulse skew (|tpHR - tpLD|) tsk(p) | See Figure 6-2, S, STB and SHDN = 0V. RL = 60Ω, CL = 100pF | typ 5 ns | 9 |
| Differential output signal rise time tr | See Figure 6-2, S, STB and SHDN = 0V. RL = 60Ω, CL = 100pF | typ 17 ns | 9 |
| Differential output signal fall time tf | See Figure 6-2, S, STB and SHDN = 0V. RL = 60Ω, CL = 100pF | typ 9 ns | 9 |
| Driver dominant time out tTXD_DTO | See Figure 6-8, RL = 60Ω, CL = 100pF | min 1.2 · typ 2.6 · max 3.8 ms | 9 |
| Propagation delay time, bus recessive input to high RXD output tpRH | See Figure 6-3, CL(RXD) = 15pF CANL = 1.5V, CANH = 3.5V | typ 62 ns | 9 |
| Propagation delay time, bus dominant input to RXD low output tpDL | See Figure 6-3, CL(RXD) = 15pF CANL = 1.5V, CANH = 3.5V | typ 56 ns | 9 |
| Output signal rise time (RXD) tr | See Figure 6-3, CL(RXD) = 15pF CANL = 1.5V, CANH = 3.5V | typ 7 ns | 9 |
| Output signal fall time (RXD) tf | See Figure 6-3, CL(RXD) = 15pF CANL = 1.5V, CANH = 3.5V | typ 6 ns | 9 |
| Receiver dominant time out tRXD_DTO | See Figure 6-10, CL(RXD) = 15pF | min 1.6 · typ 3 · max 5 ms | 9 |
Pins, by the datasheet
8- 1 TXD
- CAN transmit data input; LOW for dominant and HIGH for recessive bus states; integrated pull up. · p. 4
- 2 GND
- Ground connection. · p. 4
- 3 VCC
- 3.3-V supply voltage. · p. 4
- 4 RXD
- CAN receive data output; LOW for dominant and HIGH for recessive bus states; tri-state. · p. 4
- 5 FAULT
- Open drain fault output pin. · p. 4
- 6 CANL
- Low level CAN bus line. · p. 4
- 7 CANH
- High level CAN bus line. · p. 4
- 8 S
- Drive high for silent mode; integrated pull down. · p. 4
Parts like it
8MAX3051EKA+T
SOT-23-8-40℃~+85℃ 15uA 1Mbps 3.3V 70mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSMaxim Integrated (Analog Devices)CAN TransceiversTCAN332GDCN
SOT-23-8-40℃~+125℃ 20uA 3V~3.6V 5Mbps 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN330GDCN
SOT-23-8-40℃~+125℃ 1 2.5uA 3V~3.6V 55mA 5Mbps CAN FD Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Silent mode SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN334GDCN
SOT-23-8-40℃~+125℃ 20uA 3.3V 55mA 5Mbps CAN FD Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN337GDCN
SOT-23-8-40℃~+125℃ 20uA 3V~3.6V 5Mbps 60mA CAN Transceiver SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN1044VDDFRQ1
TSOT-23-8-40℃~+125℃ 1 1uA 4.5V~5.5V 70mA 8Mbps CAN FD Transceiver TSOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN1044AVDDFRQ1
TSOT-23-8-40℃~+150℃ 1.5uA 4.5V~5.5V 5Mbps 70mA CAN FD Transceiver TSOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversTCAN330DCN
SOT-23-8-40℃~+125℃ 1 1Mbps 2.5mA 3V~3.6V 60mA CAN Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Short-Circuit Protection、Silent mode SOT-23-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
Questions
Is there a KiCad symbol and footprint for the TCAN337DCN?
Yes. The symbol is Interface_CAN_LIN:TCAN337 and the footprint Package_TO_SOT_SMD:SOT-23-8, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TCAN337DCN?
SOT-23-8, with 8 pins. Its footprint is drawn on this page.
Where is the TCAN337DCN datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TCAN337DCN?
JLCPCB lists it as part C2671619, with 28 in stock; the sellers' links on this page open their listings.
What can replace the TCAN337DCN?
Parts like it in the library: the MAX3051EKA+T by Maxim Integrated (Analog Devices), the TCAN332GDCN by Texas Instruments, the TCAN330GDCN by Texas Instruments and the TCAN334GDCN by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.