Skip to the content
12345678910111213141516

TCA9546APW

Texas InstrumentsExtended

-40℃~+85℃ 1.65V~5.5V 1ns@5.5V,50pF 2uA 7mA Bus Switch Level shifting、Hot-swap protection Single Supply TSSOP-16 Signal Switches, Multiplexers, Decoders ROHS

Part id
ti/TCA9546APW
Category
Signal Switches, Multiplexers, Decoders
Package
TSSOP-16
Pins
16
In stock
15,476 at JLCPCB (C201653)
Used on
5 open-source boards

Overview

The TCA9546APW is a signal Switches, Multiplexers, Decoder made by Texas Instruments in a TSSOP-16 package with 16 pins. -40℃~+85℃ 1.65V~5.5V 1ns@5.5V,50pF 2uA 7mA Bus Switch Level shifting、Hot-swap protection Single Supply TSSOP-16 Signal Switches, Multiplexers, Decoders ROHS.

PCBKit's library has its KiCad symbol (Interface_Expansion:TCA9546APW, from KiCad's library) and its footprint (Package_SO:TSSOP-16_4.4x5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 15,476 are in stock at JLCPCB (part C201653). 5 open-source boards in 4 repositories on GitHub use it.

Symbol

1A02A13RESET4SD05SC06SD17SC18GND9SD210SC211SD312SC313A214SCL15SDA16VCC
Interface_Expansion:TCA9546APWFrom KiCad's library

Footprint

12345678910111213141516
Package_SO:TSSOP-16_4.4x5mm_P0.65mmFrom KiCad's library

From the datasheet

12
Supply, least
1.65 V · VCC, recommended operating min · p. 4
Supply, most
5.5 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
7 V · VCC, absolute max · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
85 °C · Operating free-air temperature max · p. 4
Takes working
50 µA · VCC operating current typical, 5.5 V, fSCL = 400 kHz, IO = 0 · p. 5
Takes asleep
1.6 µA · VCC standby current typical, 5.5 V, IO = 0 · p. 5
A pin gives at most
25 mA · Output current absolute max magnitude · p. 4
Junction to air (PW)
122.3 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (PW)
56.6 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (PW)
57.4 K/W · Junction-to-board thermal resistance · p. 4
Data rate, most
400 kbit/s · Fast mode I2C clock frequency max · p. 6

What it is and has

9
Channels
4-channel bidirectional translating I2C switch · p. 10
Interface
I2C Bus and SMBus compatible · p. 1
Reset
Active-low reset input · p. 1
Channel selection
Any combination via I2C bus · p. 1
Power-up state
All switch channels deselected · p. 1
Hot insertion
Supported · p. 1
Clock frequency
0 to 400 kHz · p. 1
Bus compatibility
I2C Bus and SMBus · p. 1
Channel selection
Via I2C Bus, in any combination · p. 1

Around it

11
res not specified
between RESET and VCC or VDPUM; Pull-up resistor if RESET is not used. · p. 3
res not specified
between SD0 and VDPU0; Serial data pull-up resistor. · p. 3
res not specified
between SC0 and VDPU0; Serial clock pull-up resistor. · p. 3
res not specified
between SD1 and VDPU1; Serial data pull-up resistor. · p. 3
res not specified
between SC1 and VDPU1; Serial clock pull-up resistor. · p. 3
res not specified
between SD2 and VDPU2; Serial data pull-up resistor. · p. 3
res not specified
between SC2 and VDPU2; Serial clock pull-up resistor. · p. 3
res not specified
between SD3 and VDPU3; Serial data pull-up resistor. · p. 3
res not specified
between SC3 and VDPU3; Serial clock pull-up resistor. · p. 3
res not specified
between SCL and VDPUM; Master serial clock pull-up resistor. · p. 3
res not specified
between SDA and VDPUM; Master serial data pull-up resistor. · p. 3

Specifications

102
ParameterConditionsAs printedPage
Supply voltage range VCCOver operating free-air temperature rangemin -0.5 · max 7 V4
Input voltage range VIOver operating free-air temperature rangemin -0.5 · max 7 V4
Input current IIMagnitude; rating printed as ±20max 20 mA4
Output current IOMagnitude; rating printed as ±25max 25 mA4
Continuous current through VCCMagnitude; rating printed as ±100max 100 mA4
Continuous current through GNDMagnitude; rating printed as ±100max 100 mA4
Total power dissipation PtotOver operating free-air temperature rangemax 400 mW4
Operating free-air temperature range TAmin -40 · max 85 °C4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; magnitude, printed as ±4000max 4000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; magnitude, printed as ±1500max 1500 V4
Supply voltage VCCmin 1.65 · max 5.5 V4
High-level input voltage VIHSCL, SDA; minimum 0.7 × VCCmax 6 V4
Low-level input voltage VILSCL, SDA; maximum 0.3 × VCCmin -0.5 V4
Low-level input voltage VILA2–A0, RESET; maximum 0.3 × VCCmin -0.5 V4
Operating free-air temperature TAmin -40 · max 85 °C4
Junction-to-ambient thermal resistance RθJAPW, 16 PINStyp 122.3 °C/W4
Junction-to-case (top) thermal resistance RθJCtopPW, 16 PINStyp 56.6 °C/W4
Junction-to-board thermal resistance RθJBPW, 16 PINStyp 57.4 °C/W4
Junction-to-top characterization parameter ψJTPW, 16 PINStyp 10.9 °C/W4
Junction-to-board characterization parameter ψJBPW, 16 PINStyp 66.8 °C/W4
Power-on reset voltage, VCC rising VPORRNo load, VI = VCC or GND; RESET = VCC when other inputs are GNDtyp 1.2 · max 1.5 V5
Power-on reset voltage, VCC falling VPORFNo load, VI = VCC or GND; RESET = VCC when other inputs are GNDmin 0.8 · typ 1 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 5 Vtyp 3.6 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 4.5 V to 5.5 Vmin 2.6 · max 4.5 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 3.3 Vtyp 1.9 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 3 V to 3.6 Vmin 1.6 · max 2.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 2.5 Vtyp 1.4 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 2.3 V to 2.7 Vmin 1 · max 1.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 1.8 Vtyp 0.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA; VCC = 1.65 V to 1.95 Vmin 0.5 · max 1.1 V5
SDA IOLVOL = 0.4 V; VCC = 1.65 V to 5.5 Vmin 3 · typ 7 mA5
SDA IOLVOL = 0.6 V; VCC = 1.65 V to 5.5 Vmin 6 · typ 10 mA5
SCL, SDA IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; magnitude, printed as ±1max 1 uA5
SC3–SC0, SD3–SD0 IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; magnitude, printed as ±1max 1 uA5
A2–A0 IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; magnitude, printed as ±1max 1 uA5
RESET IIVI = VCC or GND; VCC = 1.65 V to 5.5 V; magnitude, printed as ±1max 1 uA5
Operating mode ICCfSCL = 400 kHz; VI = VCC or GND; IO = 0; tr,max = 300 ns; VCC = 5.5 Vtyp 50 uA5
Operating mode ICCfSCL = 400 kHz; VI = VCC or GND; IO = 0; tr,max = 300 ns; VCC = 3.6 Vtyp 20 uA5
Operating mode ICCfSCL = 400 kHz; VI = VCC or GND; IO = 0; tr,max = 300 ns; VCC = 2.7 Vtyp 11 uA5
Operating mode ICCfSCL = 400 kHz; VI = VCC or GND; IO = 0; tr,max = 300 ns; VCC = 1.65 Vtyp 6 uA5
Operating mode ICCfSCL = 100 kHz; VI = VCC or GND; IO = 0; tr,max = 1 us; VCC = 5.5 Vtyp 35 uA5
Operating mode ICCfSCL = 100 kHz; VI = VCC or GND; IO = 0; tr,max = 1 us; VCC = 3.6 Vtyp 14 uA5
Operating mode ICCfSCL = 100 kHz; VI = VCC or GND; IO = 0; tr,max = 1 us; VCC = 2.7 Vtyp 5 uA5
Operating mode ICCfSCL = 100 kHz; VI = VCC or GND; IO = 0; tr,max = 1 us; VCC = 1.65 Vtyp 2 uA5
Standby mode ICCLow inputs; VI = GND; RESET = VCC; IO = 0; VCC = 5.5 Vtyp 1.6 · max 2 uA5
Standby mode ICCLow inputs; VI = GND; RESET = VCC; IO = 0; VCC = 3.6 Vtyp 1 · max 1.3 uA5
Standby mode ICCLow inputs; VI = GND; RESET = VCC; IO = 0; VCC = 2.7 Vtyp 0.7 · max 1.1 uA5
Standby mode ICCLow inputs; VI = GND; RESET = VCC; IO = 0; VCC = 1.65 Vtyp 0.4 · max 0.55 uA5
Standby mode ICCHigh inputs; VI = VCC; IO = 0; VCC = 5.5 Vtyp 1.6 · max 2 uA5
Standby mode ICCHigh inputs; VI = VCC; IO = 0; VCC = 3.6 Vtyp 1 · max 1.3 uA5
Standby mode ICCHigh inputs; VI = VCC; IO = 0; VCC = 2.7 Vtyp 0.7 · max 1.1 uA5
Standby mode ICCHigh inputs; VI = VCC; IO = 0; VCC = 1.65 Vtyp 0.4 · max 0.55 uA5
Supply-current change ΔICCSCL, SDA; SCL or SDA input at 0.6 V; other inputs at VCC or GND; VCC = 1.65 V to 5.5 Vtyp 2 · max 15 uA5
Supply-current change ΔICCSCL, SDA; SCL or SDA input at VCC – 0.6 V; other inputs at VCC or GND; VCC = 1.65 V to 5.5 Vtyp 2 · max 15 uA5
A2–A0 CiVI = VCC or GND; VCC = 1.65 V to 5.5 Vtyp 4.5 · max 6 pF5
RESET CiVI = VCC or GND; VCC = 1.65 V to 5.5 Vtyp 4.5 · max 5.5 pF5
SCL, SDA Cio(OFF)VI = VCC or GND; Switch OFF; VCC = 1.65 V to 5.5 Vtyp 15 · max 19 pF5
SC3–SC0, SD3–SD0 Cio(OFF)VI = VCC or GND; Switch OFF; VCC = 1.65 V to 5.5 Vtyp 6 · max 8 pF5
Switch on-state resistance RONVO = 0.4 V; IO = 15 mA; VCC = 4.5 V to 5.5 Vmin 4 · typ 10 · max 16 Ω6
Switch on-state resistance RONVO = 0.4 V; IO = 15 mA; VCC = 3 V to 3.6 Vmin 5 · typ 13 · max 20 Ω6
Switch on-state resistance RONVO = 0.4 V; IO = 10 mA; VCC = 2.3 V to 2.7 Vmin 7 · typ 16 · max 45 Ω6
Switch on-state resistance RONVO = 0.4 V; IO = 10 mA; VCC = 1.65 V to 1.95 Vmin 10 · typ 25 · max 70 Ω6
I2C clock frequency fsclSTANDARD MODE I2C BUSmin 0 · max 100 kHz6
I2C clock frequency fsclFAST MODE I2C BUSmin 0 · max 400 kHz6
I2C clock high time tschSTANDARD MODE I2C BUSmin 4 us6
I2C clock high time tschFAST MODE I2C BUSmin 0.6 us6
I2C clock low time tsclSTANDARD MODE I2C BUSmin 4.7 us6
I2C clock low time tsclFAST MODE I2C BUSmin 1.3 us6
I2C spike time tspSTANDARD MODE I2C BUSmax 50 ns6
I2C spike time tspFAST MODE I2C BUSmax 50 ns6
I2C serial-data setup time tsdsSTANDARD MODE I2C BUSmin 250 ns6
I2C serial-data setup time tsdsFAST MODE I2C BUSmin 100 ns6
I2C serial-data hold time tsdhSTANDARD MODE I2C BUS; see footnote (1)min 0 us6
I2C serial-data hold time tsdhFAST MODE I2C BUS; see footnote (1)min 0 us6
I2C input rise time ticrSTANDARD MODE I2C BUSmax 1000 ns6
I2C input rise time ticrFAST MODE I2C BUS; minimum 20 + 0.1Cb, Cb in pFmax 300 ns6
I2C input fall time ticfSTANDARD MODE I2C BUSmax 300 ns6
I2C input fall time ticfFAST MODE I2C BUS; minimum 20 + 0.1Cb, Cb in pFmax 300 ns6
I2C output fall time tocfSTANDARD MODE I2C BUS; 10-pF to 400-pF busmax 300 ns6
I2C output fall time tocfFAST MODE I2C BUS; 10-pF to 400-pF bus; minimum 20 + 0.1Cb, Cb in pFmax 300 ns6
I2C bus free time between stop and start tbufSTANDARD MODE I2C BUSmin 4.7 us6
I2C bus free time between stop and start tbufFAST MODE I2C BUSmin 1.3 us6
I2C start or repeated start condition setup tstsSTANDARD MODE I2C BUSmin 4.7 us6
I2C start or repeated start condition setup tstsFAST MODE I2C BUSmin 0.6 us6
I2C start or repeated start condition hold tsthSTANDARD MODE I2C BUSmin 4 us6
I2C start or repeated start condition hold tsthFAST MODE I2C BUSmin 0.6 us6
I2C stop condition setup tspsSTANDARD MODE I2C BUSmin 4 us6
I2C stop condition setup tspsFAST MODE I2C BUSmin 0.6 us6
Valid-data time (high to low) tvdL(Data)STANDARD MODE I2C BUS; SCL low to SDA output low valid; 1-kΩ pullup resistor and 50-pF loadmax 1 us6
Valid-data time (high to low) tvdL(Data)FAST MODE I2C BUS; SCL low to SDA output low valid; 1-kΩ pullup resistor and 50-pF loadmax 1 us6
Valid-data time (low to high) tvdH(Data)STANDARD MODE I2C BUS; SCL low to SDA output high valid; 1-kΩ pullup resistor and 50-pF loadmax 0.6 us6
Valid-data time (low to high) tvdH(Data)FAST MODE I2C BUS; SCL low to SDA output high valid; 1-kΩ pullup resistor and 50-pF loadmax 0.6 us6
Valid-data time of ACK condition tvd(ack)STANDARD MODE I2C BUS; ACK signal from SCL low to SDA output lowmax 1 us6
Valid-data time of ACK condition tvd(ack)FAST MODE I2C BUS; ACK signal from SCL low to SDA output lowmax 1 us6
I2C bus capacitive load CbSTANDARD MODE I2C BUSmax 400 pF6
I2C bus capacitive load CbFAST MODE I2C BUSmax 400 pF6
Propagation delay time tpdRON = 20 Ω, CL = 15 pF; SDA or SCL to SDn or SCnmax 0.3 ns6
Propagation delay time tpdRON = 20 Ω, CL = 50 pF; SDA or SCL to SDn or SCnmax 1 ns6
Pulse duration, RESET low tWLOver recommended operating free-air temperature rangemin 6 ns7
RESET time (SDA clear) trstOver recommended operating free-air temperature rangemax 500 ns7
Recovery time from RESET to start tREC(STA)Over recommended operating free-air temperature rangemin 0 ns7

Pins, by the datasheet

16
1 A0
Address input 0. Connect directly to VCC or ground. · p. 3
2 A1
Address input 1. Connect directly to VCC or ground. · p. 3
3 RESET
Active low reset input. Connect to VCC or VDPUM through a pull-up resistor if not used. · p. 3
4 SD0
Serial data 0. Connect to VDPU0 through a pull-up resistor. · p. 3
5 SC0
Serial clock 0. Connect to VDPU0 through a pull-up resistor. · p. 3
6 SD1
Serial data 1. Connect to VDPU1 through a pull-up resistor. · p. 3
7 SC1
Serial clock 1. Connect to VDPU1 through a pull-up resistor. · p. 3
8 GND
Ground. · p. 3
9 SD2
Serial data 2. Connect to VDPU2 through a pull-up resistor. · p. 3
10 SC2
Serial clock 2. Connect to VDPU2 through a pull-up resistor. · p. 3
11 SD3
Serial data 3. Connect to VDPU3 through a pull-up resistor. · p. 3
12 SC3
Serial clock 3. Connect to VDPU3 through a pull-up resistor. · p. 3
13 A2
Address input 2. Connect directly to VCC or ground. · p. 3
14 SCL
Serial clock line. Connect to VDPUM through a pull-up resistor. · p. 3
15 SDA
Serial data line. Connect to VDPUM through a pull-up resistor. · p. 3
16 VCC
Supply power. · p. 3

Ordering codes, by the datasheet

6
TCA9546ADR
SOIC (D), 16 pins · 2500-piece large tape and reel; NIPDAU lead finish · p. 23
TCA9546ADR.B
SOIC (D), 16 pins · 2500-piece large tape and reel; NIPDAU lead finish · p. 23
TCA9546APWR
TSSOP (PW), 16 pins · 2000-piece large tape and reel; NIPDAU or SN lead finish · p. 23
TCA9546APWR.B
TSSOP (PW), 16 pins · 2000-piece large tape and reel; NIPDAU lead finish · p. 23
TCA9546APWRG4
TSSOP (PW), 16 pins · 2000-piece large tape and reel; NIPDAU lead finish · p. 23
TCA9546APWRG4.B
TSSOP (PW), 16 pins · 2000-piece large tape and reel; NIPDAU lead finish · p. 23

Open-source boards using it

5
  • 4 layers100 × 90.1 mmMoBo V2-1, the printed circuit board in 3D

    MoBo V2-1

    robotique-udes/Exo_Electric

    This repo contains all the information about the PCB and electrical schematics of Biogenius.

    99 parts1GPL-2.0
  • 2 layers89 × 92.5 mmKabot, the printed circuit board in 3D

    Kabot

    kabot-io/kabot-hardware

    Hardware source and production files to recreate Kabot robot in physical world

    149 parts
  • 2 layers120 × 185 mm45lux, the printed circuit board in 3D

    45lux

    lachlanfysh/45lux

    4x5 large format camera light meter PCB — 16x TSL2591 HDR sensors, ESP32-S3 BLE, SSD1327 OLED, LIS2DH IMU

    70 parts
  • 4 layers50.7 × 52 mmGk oled pcb, the printed circuit board in 3D

    Gk oled pcb

    jncronin/gk

    This respository provides PCB schematics, firmware and debugging support for the gkv4 handheld game console and its operating system, gkos. For the original STM32H7S7-based gk, see README-v3.md.

    48 parts79
  • 2 layers120 × 185 mm45lux fixed, the printed circuit board in 3D

    45lux fixed

    lachlanfysh/45lux

    4x5 large format camera light meter PCB — 16x TSL2591 HDR sensors, ESP32-S3 BLE, SSD1327 OLED, LIS2DH IMU

    59 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCA9546APW?

Yes. The symbol is Interface_Expansion:TCA9546APW and the footprint Package_SO:TSSOP-16_4.4x5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCA9546APW?

TSSOP-16, with 16 pins. Its footprint is drawn on this page.

Where is the TCA9546APW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCA9546APW?

JLCPCB lists it as part C201653, with 15,476 in stock; the sellers' links on this page open their listings.

What can replace the TCA9546APW?

Parts like it in the library: the SN74HC138PW by Texas Instruments, the 74HC4851PW-Q100,11 by Nexperia, the SGM330A-YTS/TR by SG Micro and the SN74LVC257APW by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCA9546APW?

5 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.