SN65HVD35D
Texas InstrumentsExtended
-40℃~+85℃ 1 1 22nA 256 3V~3.6V 5Mbps Full-Duplex Transceiver ±16kV SOIC-14 RS-485 / RS-422 ICs ROHS
- Part id
- ti/SN65HVD35D
- Category
- RS 485, RS 422 ICs
- Package
- SOIC-14
- Pins
- 14
- In stock
- 76 at JLCPCB (C411877)
Overview
The SN65HVD35D is a RS 485, RS 422 IC made by Texas Instruments in a SOIC-14 package with 14 pins. -40℃~+85℃ 1 1 22nA 256 3V~3.6V 5Mbps Full-Duplex Transceiver ±16kV SOIC-14 RS-485 / RS-422 ICs ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TPT482-SO2R, from EasyEDA) and its footprint (Package_SO:SOIC-14_3.9x8.7mm_P1.27mm, from KiCad's library), ready for a KiCad board. 76 are in stock at JLCPCB (part C411877).
Symbol
Footprint
From the datasheet
14- Supply, least
- 3 V · VCC, recommended operating min · p. 8
- Supply, most
- 3.6 V · VCC, recommended operating max · p. 8
- Supply, absolute maximum
- 6 V · VCC, absolute max · p. 7
- Works from
- -40 °C · Ambient characterization min · p. 1
- Works up to
- 85 °C · Ambient characterization max · p. 1
- Junction, hottest
- 150 °C · Junction temperature, recommended operating max · p. 8
- A pin gives at most
- 11 mA · R receiver output, absolute max · p. 7
- Takes working
- 6.5 mA · VCC, receiver and driver enabled, no load, max · p. 11
- Takes asleep
- 22 nA · VCC, receiver and driver disabled, no load, typical · p. 11
- Data rate, most
- 1 Mbit/s · SN65HVD35 signaling rate max · p. 4
- Edge
- 180 ns · Driver differential output fall time, RL = 54 Ω, CL = 50 pF, typical · p. 11
- Junction to air (D (SOIC), 14 PINS)
- 93.2 K/W · Junction-to-ambient thermal resistance · p. 8
- Junction to case (D (SOIC), 14 PINS)
- 47.5 K/W · Junction-to-case top thermal resistance · p. 8
- Junction to board (D (SOIC), 14 PINS)
- 49.4 K/W · Junction-to-board thermal resistance · p. 8
What it is and has
11- Signaling rate
- 1 Mbps · p. 4
- Bus loading
- 1/8 unit load · p. 4
- Enables
- Driver and receiver enables · p. 4
- Input tolerance
- 5 V · p. 1
- Failsafe
- Bus idle, open, and short-circuit · p. 1
- Protection
- Driver current limiting and thermal shutdown · p. 1
- Standards
- Designed for RS-422 and RS-485 networks · p. 1
- Interface
- 3.3-V full-duplex RS-485 driver and receiver · p. 1
- Bus-pin ESD protection
- Exceeds 15-kV HBM · p. 1
- Receiver failsafe
- Open, shorted and idle bus conditions · p. 22
- Bus-pin ESD protection
- exceeds 15-kV HBM · p. 1
Specifications
92| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply voltage VCC | Over operating free-air temperature range | min -0.3 · max 6 V | 7 |
| Voltage at any bus terminal (A, B, Y, Z) V(A), V(B), V(Y), V(Z) | Over operating free-air temperature range | min -9 · max 14 V | 7 |
| Voltage input, transient pulse through 100 Ω. See Figure 8-13 (A, B, Y, Z) V(TRANS) | Survivability only; receiver output state not specified | min -50 · max 50 V | 7 |
| Input voltage (D, DE, RE) VI | Over operating free-air temperature range | min -0.5 · max 7 V | 7 |
| Output current (receiver output only, R) IO | Over operating free-air temperature range | max 11 mA | 7 |
| Storage Temperature Tstg | max 125 °C | 7 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; bus pins and GND; ± value | max 16000 V | 7 |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001; all pins; ± value | max 4000 V | 7 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101; ± value | max 1000 V | 7 |
| Supply voltage VCC | Over operating free-air temperature range | min 3 · max 3.6 V | 8 |
| Voltage at any bus pin (separately or common mode) VI or VIC | min -7 · max 12 V | 8 | |
| Signaling rate 1/tUI | SN65HVD35 | max 1 Mbps | 8 |
| Differential load resistance RL | 60 Ω is nominal | min 54 · typ 60 Ω | 8 |
| High-level input voltage VIH | D, DE, RE; maximum VCC | min 2 V | 8 |
| Low-level input voltage VIL | D, DE, RE | min 0 · max 0.8 V | 8 |
| Differential input voltage VID | min -12 · max 12 V | 8 | |
| High-level output current IOH | Driver | min -60 mA | 8 |
| High-level output current IOH | Receiver | min -8 mA | 8 |
| Low-level output current IOL | Driver | max 60 mA | 8 |
| Low-level output current IOL | Receiver | max 8 mA | 8 |
| Junction temperature TJ | min -40 · max 150 °C | 8 | |
| Junction-to-ambient thermal resistance RθJA | SN65HVD35; D (SOIC), 14 PINS | typ 93.2 °C/W | 8 |
| Junction-to-case (top) thermal resistance RθJC(top) | SN65HVD35; D (SOIC), 14 PINS | typ 47.5 °C/W | 8 |
| Junction-to-board thermal resistance RθJB | SN65HVD35; D (SOIC), 14 PINS | typ 49.4 °C/W | 8 |
| Junction-to-top characterization parameter ψJT | SN65HVD35; D (SOIC), 14 PINS | typ 11.2 °C/W | 8 |
| Junction-to-board characterization parameter ψJB | SN65HVD35; D (SOIC), 14 PINS | typ 48.9 °C/W | 8 |
| Input clamp voltage VI(K) | II = –18 mA | min -1.5 V | 9 |
| Steady-state differential output voltage |VOD(SS)| | IO = 0; maximum VCC | min 2.5 V | 9 |
| Steady-state differential output voltage |VOD(SS)| | RL = 54 Ω, See Figure 8-2 (RS-485) | min 1.5 · typ 2 V | 9 |
| Steady-state differential output voltage |VOD(SS)| | RL = 100 Ω, See Figure 8-2 (RS-422); VCC is 3.3 VDC ± 5% | min 2 · typ 2.3 V | 9 |
| Steady-state differential output voltage |VOD(SS)| | Vtest = –7 V to 12 V, See Figure 8-3 | min 1.5 V | 9 |
| Change in magnitude of steady-state differential output voltage between states Δ|VOD(SS)| | RL = 54 Ω, See Figure 8-2 and Figure 8-3 | min -0.2 · max 0.2 V | 9 |
| Peak-to-peak common-mode output voltage VOC(PP) | SN65HVD35; See Figure 8-5 | typ 0.25 V | 9 |
| Steady-state common-mode output voltage VOC(SS) | See Figure 8-5 | min 1.6 · max 2.3 V | 9 |
| Change in steady-state common-mode output voltage ΔVOC(SS) | See Figure 8-5 | min -0.05 · max 0.05 V | 9 |
| High-impedance state output current IZ(Z) or IY(Z) | SN65HVD35; VCC = 3 V or 0 V, DE = 0 V, VZ or VY = 12 V, other input at 0 V | max 90 uA | 9 |
| High-impedance state output current IZ(Z) or IY(Z) | SN65HVD35; VCC = 3 V or 0 V, DE = 0 V, VZ or VY = –7 V, other input at 0 V | min -10 uA | 9 |
| Short Circuit output current IZ(S) or IY(S) | VZ or VY = –7 V, other input at 0 V | min -250 · max 250 mA | 9 |
| Short Circuit output current IZ(S) or IY(S) | VZ or VY = 12 V, other input at 0 V | min -250 · max 250 mA | 9 |
| Input current II | D, DE | min 0 · max 100 uA | 9 |
| Differential output capacitance C(OD) | VOD = 0.4 sin (4E6πt) + 0.5 V, DE at 0 V | typ 16 pF | 9 |
| Positive-going differential input threshold voltage VIT+ | IO = –8 mA | max -0.02 V | 10 |
| Negative-going differential input threshold voltage VIT- | IO = 8 mA | min -0.2 V | 10 |
| Hysteresis voltage (VIT+ – VIT–) Vhys | typ 50 mV | 10 | |
| Enable-input clamp voltage VIK | II = –18 mA | min -1.5 V | 10 |
| Output voltage VO | VID = 200 mV, IO = –8 mA, See Figure 8-9 | min 2.4 V | 10 |
| Output voltage VO | VID = –200 mV, IO = 8 mA, See Figure 8-9 | max 0.4 V | 10 |
| High-impedance-state output current IO(Z) | VO = 0 or VCC, RE at VCC | min -1 · max 1 uA | 10 |
| Bus input current IA or IB | SN65HVD35; VA or VB = 12 V, other input at 0 V | typ 0.05 · max 0.1 mA | 10 |
| Bus input current IA or IB | SN65HVD35; VA or VB = 12 V, VCC = 0 V, other input at 0 V | typ 0.06 · max 0.1 mA | 10 |
| Bus input current IA or IB | SN65HVD35; VA or VB = –7 V, other input at 0 V | min -0.1 · typ -0.04 mA | 10 |
| Bus input current IA or IB | SN65HVD35; VA or VB = –7 V, VCC = 0 V, other input at 0 V | min -0.1 · typ -0.03 mA | 10 |
| Input current, RE IIH | VIH = 0.8 V or 2 V | min -60 uA | 10 |
| Differential input capacitance CID | VID = 0.4 sin (4E6πt) + 0.5 V, DE at 0 V | typ 15 pF | 10 |
| Power Dissipation (worst case) PD | SN65HVD35; driver and receiver enabled, 50% duty cycle square-wave signal at 1 Mbps; VCC = 3.6 V, TJ = 140°C, RL = 54 Ω, CL = 50 pF (driver), CL = 15 pF (receiver) | max 248 mW | 10 |
| Thermal Shut-down Junction Temperature TSD | typ 170 °C | 10 | |
| Supply current ICC | SN65HVD35; RE at 0 V, D at 0 V or VCC, DE at 0 V, no load (receiver enabled and driver disabled) | max 2.2 mA | 11 |
| Supply current ICC | SN65HVD35; RE at VCC, D at VCC, DE at 0 V, no load (receiver disabled and driver disabled) | typ 0.022 · max 1 uA | 11 |
| Supply current ICC | SN65HVD35; RE at 0 V, D at 0 V or VCC, DE at VCC, no load (receiver enabled and driver enabled) | max 6.5 mA | 11 |
| Supply current ICC | SN65HVD35; RE at VCC, D at 0 V or VCC, DE at VCC, no load (receiver disabled and driver enabled) | max 6.2 mA | 11 |
| Propagation delay time, low-to-high-level output tPLH | SN65HVD35; RL = 54 Ω, CL = 50 pF, See Figure 8-6 | min 120 · typ 175 · max 305 ns | 11 |
| Propagation delay time, high-to-low-level output tPHL | SN65HVD35; RL = 54 Ω, CL = 50 pF, See Figure 8-6 | min 120 · typ 175 · max 305 ns | 11 |
| Differential output signal rise time tr | SN65HVD35; RL = 54 Ω, CL = 50 pF, See Figure 8-6 | min 120 · typ 185 · max 300 ns | 11 |
| Differential output signal fall time tf | SN65HVD35; RL = 54 Ω, CL = 50 pF, See Figure 8-6 | min 120 · typ 180 · max 300 ns | 11 |
| Pulse skew (|tPHL – tPLH|) tsk(p) | SN65HVD35; RL = 54 Ω, CL = 50 pF, See Figure 8-6 | typ 5.1 ns | 11 |
| Propagation delay time, high-impedance-to-high-level output tPZH1 | SN65HVD35; RL = 110 Ω, RE at 0 V, D = 3 V and S1 = Y, or D = 0 V and S1 = Z; See Figure 8-7 | max 490 ns | 12 |
| Propagation delay time, high-level-to-high-impedance output tPHZ | SN65HVD35; RL = 110 Ω, RE at 0 V, D = 3 V and S1 = Y, or D = 0 V and S1 = Z; See Figure 8-7 | max 165 ns | 12 |
| Propagation delay time, high-impedance-to-low-level output tPZL1 | SN65HVD35; RL = 110 Ω, RE at 0 V, D = 3 V and S1 = Z, or D = 0 V and S1 = Y; See Figure 8-8 | max 490 ns | 12 |
| Propagation delay time, low-level-to-high-impedance output tPLZ | SN65HVD35; RL = 110 Ω, RE at 0 V, D = 3 V and S1 = Z, or D = 0 V and S1 = Y; See Figure 8-8 | max 290 ns | 12 |
| Driver enable delay with bus voltage offset tPZH1, tPZL1 | VO= 2 V (Typ); typical at 25°C and 3.3-V supply | typ 500 · max 900 ns | 12 |
| Propagation delay time, standby-to-high-level output tPZH2 | RL = 110 Ω, RE at 3 V, D = 3 V and S1 = Y, or D = 0 V and S1 = Z; See Figure 8-7 | max 4000 ns | 12 |
| Propagation delay time, standby-to-low-level output tPZL2 | RL = 110 Ω, RE at 3 V, D = 3 V and S1 = Z, or D = 0 V and S1 = Y; See Figure 8-8 | max 4000 ns | 12 |
| Propagation delay time, low-to-high-level output tPLH | SN65HVD35; VID = –1.5 V to 1.5 V, CL = 15 pF; See Figure 8-10; typical at 25°C and 3.3-V supply | typ 47 · max 70 ns | 12 |
| Propagation delay time, high-to-low-level output tPHL | SN65HVD35; VID = –1.5 V to 1.5 V, CL = 15 pF; See Figure 8-10; typical at 25°C and 3.3-V supply | typ 49 · max 70 ns | 12 |
| Pulse skew (|tPHL – tPLH|) tsk(p) | SN65HVD35; VID = –1.5 V to 1.5 V, CL = 15 pF; See Figure 8-10 | max 10 ns | 12 |
| Output signal rise time tr | VID = –1.5 V to 1.5 V, CL = 15 pF; See Figure 8-10 | max 5 ns | 12 |
| Output signal fall time tf | VID = –1.5 V to 1.5 V, CL = 15 pF; See Figure 8-10 | max 6 ns | 12 |
| Output disable time from high level tPHZ | DE at 3 V; CL = 15 pF; See Figure 8-11 | max 20 ns | 12 |
| Output enable time to high level tPZH1 | DE at 3 V; CL = 15 pF; See Figure 8-11 | max 20 ns | 12 |
| Propagation delay time, standby-to-high-level output tPZH2 | DE at 0 V; CL = 15 pF; See Figure 8-11 | max 4000 ns | 12 |
| Output disable time from low level tPLZ | DE at 3 V; CL = 15 pF; See Figure 8-12 | max 20 ns | 12 |
| Output enable time to low level tPZL1 | DE at 3 V; CL = 15 pF; See Figure 8-12 | max 20 ns | 12 |
| Propagation delay time, standby-to-low-level output tPZL2 | DE at 0 V; CL = 15 pF; See Figure 8-12 | max 4000 ns | 12 |
| TA < 25°C RATING | 14-pin D (SOIC); JEDEC thermal model Low k | max 765 mW | 13 |
| DERATING FACTOR ABOVE TA = 25°C | 14-pin D (SOIC); JEDEC thermal model Low k | typ 6.1 mW/°C | 13 |
| TA = 85°C RATING | 14-pin D (SOIC); JEDEC thermal model Low k | max 400 mW | 13 |
| TA = 105°C RATING | 14-pin D (SOIC); JEDEC thermal model Low k | max 275 mW | 13 |
| TA < 25°C RATING | 14-pin D (SOIC); JEDEC thermal model High k | max 1350 mW | 13 |
| DERATING FACTOR ABOVE TA = 25°C | 14-pin D (SOIC); JEDEC thermal model High k | typ 10.8 mW/°C | 13 |
| TA = 85°C RATING | 14-pin D (SOIC); JEDEC thermal model High k | max 705 mW | 13 |
| TA = 105°C RATING | 14-pin D (SOIC); JEDEC thermal model High k | max 485 mW | 13 |
| TA = 125°C RATING | 14-pin D (SOIC); JEDEC thermal model High k | max 270 mW | 13 |
Ordering codes, by the datasheet
4- SN65HVD35D
- SOIC (D), 14 pins · Obsolete; operating temperature -40 to 85°C · p. 33
- SN65HVD35DR
- SOIC (D), 14 pins · Active; 2500, LARGE T&R; operating temperature -40 to 85°C · p. 33
- SN65HVD35DR.A
- SOIC (D), 14 pins · Active; 2500, LARGE T&R; operating temperature -40 to 85°C · p. 33
- SN65HVD35DRG4
- SOIC (D), 14 pins · Active; 2500, LARGE T&R; operating temperature -40 to 85°C · p. 33
Parts like it
8SP491EEN-L/TR
SOIC-14-40℃~+85℃ 1 1 10Mbps 32 4.75V~5.25V 900uA Full-Duplex Transceiver ±15kV SOIC-14 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsSP3070EEN-L/TR
SOIC-14-40℃~+85℃ 1 1 1.5mA 250Kbps 256 3.3V Full-Duplex Transceiver ±15kV SOIC-14 RS-485 / RS-422 ICs ROHSMaxLinearRS-485 / RS-422 ICsGB491
SOP-14-40℃~+125℃ 1 1 10Mbps 256 3.3V、5V 800uA Full-Duplex Transceiver ±15kV SOP-14 RS-485 / RS-422 ICs ROHSNJGWRS-485 / RS-422 ICsSIT3491EESD
SOP-14-40℃~+125℃ 1 1 12Mbps 240uA 256 3V~5.5V Enable shutdown、Overcurrent Protection、Low-power mode、Tx/Rx enable Full-Duplex Transceiver ±15kV SOP-14 RS-485 / RS-422 ICs ROHSSITRS-485 / RS-422 ICsSN65HVD34D
SOIC-14-40℃~+85℃ 1 1 1uA 256 3V~3.6V 5Mbps Full-Duplex Transceiver ±15kV SOIC-14 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsSN65HVD37D
SOIC-14-40℃~+85℃ 1 1 20Mbps 256 3V~3.6V 850uA Full-Duplex Transceiver ±16kV SOIC-14 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsADM3491ARZ-REEL7
SOIC-14-40℃~+85℃ 1 1 1.1mA 10Mbps 32 3V~3.6V Full-Duplex Transceiver SOIC-14 RS-485 / RS-422 ICs ROHSAnalog DevicesRS-485 / RS-422 ICsSN65HVD33D
SOIC-14-40℃~+85℃ 1 1 1uA 23Mbps 256 3V~3.6V Full-Duplex Transceiver ±15kV SOIC-14 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICs
Questions
Is there a KiCad symbol and footprint for the SN65HVD35D?
Yes. The symbol is EasyEDA_Cloud:TPT482-SO2R and the footprint Package_SO:SOIC-14_3.9x8.7mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the SN65HVD35D?
SOIC-14, with 14 pins. Its footprint is drawn on this page.
Where is the SN65HVD35D datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the SN65HVD35D?
JLCPCB lists it as part C411877, with 76 in stock; the sellers' links on this page open their listings.
What can replace the SN65HVD35D?
Parts like it in the library: the SP491EEN-L/TR by MaxLinear, the SP3070EEN-L/TR by MaxLinear, the GB491 by NJGW and the SIT3491EESD by SIT. Check their datasheets: a part that fits the footprint may still differ in its ratings.