Skip to the content
12345678

SN65HVD230MDREP

Texas InstrumentsExtended

-55℃~+125℃ 1Mbps 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHS

Part id
ti/SN65HVD230MDREP
Category
CAN Transceivers
Package
SOIC-8
Pins
8
In stock
0 at JLCPCB (C2878159)
Used on
4 open-source boards

Overview

The SN65HVD230MDREP is a CAN Transceiver made by Texas Instruments in a SOIC-8 package with 8 pins. -55℃~+125℃ 1Mbps 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHS.

PCBKit's library has its KiCad symbol (Interface_CAN_LIN:SN65HVD230, from KiCad's library) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. JLCPCB lists it (part C2878159). 4 open-source boards in 3 repositories on GitHub use it.

Symbol

1D2GND3VCC4R5Vref6CANL7CANH8Rs
Interface_CAN_LIN:SN65HVD230From KiCad's library

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

11
Supply, least
3 V · VCC, recommended operating, min · p. 5
Supply, most
3.6 V · VCC, recommended operating, max · p. 5
Supply, absolute maximum
6 V · VCC, absolute maximum · p. 5
Works from
-55 °C · Operating free-air temperature, min · p. 5
Works up to
125 °C · Operating free-air temperature, max · p. 5
Takes working
10 mA · VCC, dominant, no load, 3.3 V, 25°C, typical · p. 6
Takes at most
17 mA · VCC, dominant, no load, max · p. 6
Takes asleep
370 µA · VCC, standby, V(RS) = VCC, 3.3 V, 25°C, typical · p. 6
A pin gives at most
48 mA · Driver low-level output current, recommended operating, max · p. 5
Data rate, most
1 Mbit/s · CAN signaling rate, max · p. 2
Edge
1.5 ns · Receiver output rise time, 25°C, typical · p. 7

Open-source boards using it

4
  • 4 layers111 × 79 mmIMU board, the printed circuit board in 3D

    IMU board

    Robsic/gps-imu-interface-board

    Hardware, firmware e documentação da placa GPS/IMU e interface de encoders do carrinho elétrico RobSIC.

    31 parts
  • 2 layers85.1 × 104.1 mmPGR-06 Wheel, the printed circuit board in 3D

    PGR-06 Wheel

    patwitt/PGRacingElectronics

    https://www.pgracingteam.pl/

    61 parts4
  • 4 layers111 × 79 mmIMU board, the printed circuit board in 3D

    IMU board

    Robsic/gps-imu-interface-board

    Hardware, firmware e documentação da placa GPS/IMU e interface de encoders do carrinho elétrico RobSIC.

    31 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the SN65HVD230MDREP?

Yes. The symbol is Interface_CAN_LIN:SN65HVD230 and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the SN65HVD230MDREP?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the SN65HVD230MDREP datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the SN65HVD230MDREP?

JLCPCB lists it as part C2878159, with 0 in stock; the sellers' links on this page open their listings.

What can replace the SN65HVD230MDREP?

Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the SN65HVD230MDREP?

4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.