Skip to the content
123456

SN6505BDBV

Texas InstrumentsExtended

-55℃~+125℃ 1.56mA 160mΩ 16V 1A 2.25V~5.5V SOT-23-6 Transformer Drivers ROHS

Part id
ti/SN6505BDBV
Category
Power Management, Specialized
Package
SOT-23-6
Pins
6
In stock
1,379 at JLCPCB (C74518)
Used on
13 open-source boards

Overview

The SN6505BDBV is a power Management, Specialized made by Texas Instruments in a SOT-23-6 package with 6 pins. -55℃~+125℃ 1.56mA 160mΩ 16V 1A 2.25V~5.5V SOT-23-6 Transformer Drivers ROHS.

PCBKit's library has its KiCad symbol (Power_Management:SN6505BDBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-6, from KiCad's library), ready for a KiCad board. 1,379 are in stock at JLCPCB (part C74518). 13 open-source boards in 11 repositories on GitHub use it.

Symbol

1D12VCC3D24GND5EN6CLK
Power_Management:SN6505BDBVFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-23-6From KiCad's library

From the datasheet

17
Supply, least
2.25 V · VCC, recommended operating min · p. 4
Supply, most
5.5 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
6 V · VCC, absolute maximum · p. 4
Works from
-55 °C · Ambient temperature min · p. 4
Works up to
125 °C · Ambient temperature max · p. 4
Junction, hottest
150 °C · Junction temperature absolute max · p. 4
Takes working
1.56 mA · VCC supply current typical, RL = 50 Ω, 2.8 V < VCC < 5.5 V · p. 5
Takes at most
2.3 mA · VCC supply current max, RL = 50 Ω, 2.8 V < VCC < 5.5 V · p. 5
Takes asleep
100 nA · VCC current typical, EN = 0 · p. 5
Gives
750 mA · Output switch current max per output, 2.25 V < VCC < 2.8 V · p. 4
Gives
1 A · Output switch current max per output, 2.8 V < VCC < 5.5 V · p. 4
Current limit
1.75 A · Current clamp limit typical, 2.8 V < VCC < 5.5 V · p. 5
Current limit
650 mA · Current clamp limit min, 2.25 V < VCC < 2.8 V · p. 5
Switches at
424 kHz · D1, D2 average switching frequency typical, RL = 50 Ω to VCC · p. 5
Junction to air (DBV (SOT-23))
137.7 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (DBV (SOT-23))
57.7 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (DBV (SOT-23))
46 K/W · Junction-to-board thermal resistance · p. 4

What it is and has

6
Driver topology
Push-pull transformer driver · p. 1
Spread spectrum clocking
Integrated · p. 1
Slew-rate control
Integrated · p. 1
Protection
Thermal shutdown · p. 1
Soft-start
Reduces inrush current · p. 1
Package
6-pin SOT23 (DBV) · p. 1

Around it

4
cap 4.7 μF or greater
between VCC and GND; Low-ESR supply bypass capacitor. · p. 3
cap 10 nF to 100 nF
between VCC and GND; Device bypass capacitor; converter capacitors are MLCC. · p. 25
cap 1 μF to 10 μF
between Rectifier output and Secondary ground; Bulk capacitor to smooth the rectifier output voltage. · p. 25
cap 4.7 μF to 10 μF
between LDO output and Secondary ground; Low-ESR ceramic capacitor; select according to the LDO stability requirements. · p. 25

Specifications

40
ParameterConditionsAs printedPage
Supply voltage VCCmin -0.5 · max 6 V4
VoltageEN, CLK; maximum VCC + 0.5 V, limited to 6 V by footnote (3)min -0.5 V4
Output switch voltageD1, D2max 16 V4
Peak output switch current I(D1)Pk, I(D2)Pkmax 2.4 A4
Junction temperature TJmin -55 · max 150 °C4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±6000 Vmax 6000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±1500 Vmax 1500 V4
Supply voltage VCCmin 2.25 · max 5.5 V4
Output switch current - Primary side ID1, ID22.25 V < VCC < 2.8 Vmax 0.75 A4
Output switch current - Primary side ID1, ID22.8 V < VCC < 5.5 Vmax 1 A4
Ambient temperature TAmin -55 · max 125 °C4
Junction-to-ambient thermal resistance RθJADBV (SOT-23), 6 pinstyp 137.7 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)DBV (SOT-23), 6 pinstyp 57.7 °C/W4
Junction-to-board thermal resistance RθJBDBV (SOT-23), 6 pinstyp 46 °C/W4
Junction-to-top characterization parameter ψJTDBV (SOT-23), 6 pinstyp 13.4 °C/W4
Junction-to-board characterization parameter ψJBDBV (SOT-23), 6 pinstyp 44.9 °C/W4
Supply Current (2.8 V < VC C < 5.5) I(Vcc)SN6505B; RL = 50 Ωtyp 1.56 · max 2.3 mA5
Leakage Current on EN and CLK pin IIHEN / CLK = VCCtyp 10 · max 20 uA5
VCC current for EN = 0 IDIStyp 0.1 uA5
Leakage Current on D1,D2 for EN=0 ILKG(D1), ILKG(D2)Voltage of D1,D2 = VCCtyp 0.1 uA5
Positive-going UVLO threshold VCC+ (UVLO)max 2.25 V5
Negative-going UVLO threshold VCC- (UVLO)min 1.7 V5
UVLO threshold hysteresis VHYS (UVLO1)typ 0.3 V5
EN, CLK pin logic high threshold VIN(ON)max 0.7 VCC5
EN, CLK pin logic low threshold VIN(OFF)min 0.3 VCC5
EN, CLK pin threshold hysteresis VIN(HYS)typ 0.2 VCC5
D1, D2 average switching Frequency FSWSN6505B; RL = 50 Ω to VCC; Refer to Figure 7-3.min 363 · typ 424 · max 517 kHz5
External clock frequency on CLK pin F(EXT)SN6505Bmin 100 · max 1600 kHz5
Average ON time mismatch between D1 and D2 DMMRL = 50 Ωtyp 0 %5
Output switch on resistance R(ON)VCC = 4.5 V, ID1,ID2 = 1 Atyp 0.16 · max 0.25 Ω5
Output switch on resistance R(ON)VCC = 2.8 V, ID1,ID2 = 1 Atyp 0.19 · max 0.31 Ω5
Output switch on resistance R(ON)VCC = 2.25 V, ID1,ID2 = 0.5 Atyp 0.21 · max 0.45 Ω5
Voltage slew rates on D1 and D2 for SN6505B V(SLEWHF)RL = 50 Ω to VCC; Refer to Figure 7-3typ 152 V/us5
Current slew rates at D1 and D2 for SN6505B I(SLEWHF)RL = 5 Ω through transformer; Refer to Figure 7-4typ 41 A/us5
Current clamp limit (2.8 V < VCC < 5.5V ) ILIMmin 1.42 · typ 1.75 · max 2.15 A5
Current clamp limit (2.25 V < VCC < 2.8 V) ILIMmin 0.65 · max 1.85 A5
TSD turn on temperature TSD+min 154 · typ 168 · max 181 °C5
TSD turn off temperature TSD-min 135 · typ 150 · max 166 °C5
TSD hysteresis TSD-min 13 · typ 17 °C5

Pins, by the datasheet

6
1 D1
First power MOSFET open-drain output; connect to an outer transformer primary terminal and keep traces short. · p. 3
2 VCC
Device supply; bypass with a low-ESR capacitor of 4.7 uF or greater. Undervoltage lockout turns both outputs off when VCC ≤ 2.25 V. · p. 3
3 D2
Second power MOSFET open-drain output; connect to an outer transformer primary terminal and keep traces short. · p. 3
4 GND
Power MOSFET source return through an internal sense circuit; connect to a low-inductance ground plane. · p. 3
5 EN
Enable input; grounding or floating disables internal circuitry. Tie directly to VCC if unused. · p. 3
6 CLK
External clock input with internal pull-down; automatically uses the internal clock when no valid external clock is detected. · p. 3

Open-source boards using it

13See all 13
  • 4 layers70 × 70 mmFreeEEG32-alpha131, the printed circuit board in 3D

    FreeEEG32-alpha131

    neuroidss/FreeEEG32-alpha131

    https://hackaday.io/project/181683-freeeeg32-alpha131

    124 parts4AGPL-3.0
  • 4 layers70 × 70 mmFreeEEG128-alpha, the printed circuit board in 3D

    FreeEEG128-alpha

    m9h/freeeeg128

    Open-hardware 128-channel EEG acquisition system — design audit, firmware rewrite roadmap, Pi Zero 2W host stack, and synthesis paper

    168 parts3
  • 4 layers100 × 100 mmThree Half Bridges, the printed circuit board in 3D

    Three Half Bridges

    powermax555/Three-Half-Bridges

    Half bridge module for use in larger power conversion and motor control systems

    156 parts3
  • 2 layers58.4 × 83.2 mmMiniFeedMaster, the printed circuit board in 3D

    MiniFeedMaster

    SG-O/MiniFeedMaster

    Mainboard for automated SMT Feeder system

    141 parts1CC-BY-4.0
  • 4 layers120 × 50 mmIsolator, the printed circuit board in 3D

    Isolator

    alxgmpr/adum4165-isolator

    73 parts
  • 2 layers74.9 × 55.9 mm6s 750mA, the printed circuit board in 3D

    6s 750mA

    jsarrett/StackedCharger

    Isolated stackable LiPo charger

    121 parts
  • 4 layers66 × 76.2 mmFreeEEG32-alpha2, the printed circuit board in 3D

    FreeEEG32-alpha2

    neuroidss/FreeEEG32-alpha2

    209 partsAGPL-3.0
  • 2 layersOpenmic, the printed circuit board in 3D

    Openmic

    oliverpaddock/OpenMic

    An open source audio interface

    432 partsCERN-OHL-S-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the SN6505BDBV?

Yes. The symbol is Power_Management:SN6505BDBV and the footprint Package_TO_SOT_SMD:SOT-23-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the SN6505BDBV?

SOT-23-6, with 6 pins. Its footprint is drawn on this page.

Where is the SN6505BDBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the SN6505BDBV?

JLCPCB lists it as part C74518, with 1,379 in stock; the sellers' links on this page open their listings.

What can replace the SN6505BDBV?

Parts like it in the library: the VPS8504B by VPSC, the VPS8505 by VPSC, the SN6505ADBV by Texas Instruments and the SN6505BQDBVRQ1 by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the SN6505BDBV?

13 boards in 11 repositories on GitHub; the most starred are listed on this page, with their KiCad files.