OPA376AIDBV
Texas InstrumentsExtended
-40℃~+125℃ 0.2pA 0.2pA 1 2.2V~5.5V 260nV/℃ 2V/us 30mA 5.5MHz 5uV 7.5nV/√Hz@1kHz 760uA 76dB Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5 Precision Op Amps ROHS
- Part id
- ti/OPA376AIDBV
- Category
- Precision OpAmps
- Package
- SOT-23-5
- Pins
- 5
- In stock
- 1,478 at JLCPCB (C42134)
Overview
The OPA376AIDBV is a precision OpAmp made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃ 0.2pA 0.2pA 1 2.2V~5.5V 260nV/℃ 2V/us 30mA 5.5MHz 5uV 7.5nV/√Hz@1kHz 760uA 76dB Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5 Precision Op Amps ROHS.
PCBKit's library has its KiCad symbol (Amplifier_Operational:OPA376xxDBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 1,478 are in stock at JLCPCB (part C42134).
Symbol
Footprint
From the datasheet
10- Supply, least
- 2.2 V · V+ – V–, recommended operating min · p. 6
- Supply, most
- 5.5 V · V+ – V–, recommended operating max · p. 6
- Supply, absolute maximum
- 7 V · V+ – V–, absolute max · p. 6
- Works from
- -40 °C · Operating free-air temperature min · p. 6
- Works up to
- 150 °C · Operating free-air temperature max · p. 6
- Junction, hottest
- 150 °C · Junction temperature absolute max · p. 6
- Takes working
- 760 µA · Quiescent current typical, 25°C, IO = 0, VS = 5.5 V · p. 9
- Junction to air (DBV (SOT-23))
- 273.8 K/W · Junction-to-ambient thermal resistance · p. 7
- Junction to case (DBV (SOT-23))
- 126.8 K/W · Junction-to-case top thermal resistance · p. 7
- Junction to board (DBV (SOT-23))
- 85.9 K/W · Junction-to-board thermal resistance · p. 7
What it is and has
6- Input voltage noise density
- 7.5 nV/√Hz at 1 kHz · p. 1
- Low-frequency noise
- 0.8 μVPP, 0.1 Hz to 10 Hz · p. 1
- Input offset voltage
- 5 μV typical · p. 1
- Gain bandwidth product
- 5.5 MHz · p. 1
- Input and output
- Rail-to-rail · p. 1
- Supply operation
- Single supply · p. 1
Around it
1- cap 0.1 µF
- between V+ and ground; Low-ESR ceramic bypass capacitor placed as close to the device as possible; bypass each supply pin to ground. · p. 21
Specifications
49| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Supply VS | VS = (V+) – (V–); over operating free-air temperature range | max 7 V | 6 |
| Signal input pin | Current; input terminals diode-clamped to supply rails | min -10 · max 10 mA | 6 |
| Operating range TA | min -40 · max 150 °C | 6 | |
| Junction TJ | max 150 °C | 6 | |
| Storage Tstg | min -65 · max 150 °C | 6 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±4000 V | max 4000 V | 6 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±1000 V | max 1000 V | 6 |
| Electrostatic discharge V(ESD) | Machine model; ±200 V | max 200 V | 6 |
| Supply voltage (V+) – (V–) | Over operating free-air temperature range; equivalent split supply ±1.1 V to ±2.75 V | min 2.2 · max 5.5 V | 6 |
| Operating temperature TA | Free-air temperature | min -40 · max 150 °C | 6 |
| Junction-to-ambient thermal resistance RθJA | OPA376, DBV (SOT-23), 5 pins | typ 273.8 °C/W | 7 |
| Junction-to-case (top) thermal resistance RθJC(top) | OPA376, DBV (SOT-23), 5 pins | typ 126.8 °C/W | 7 |
| Junction-to-board thermal resistance RθJB | OPA376, DBV (SOT-23), 5 pins | typ 85.9 °C/W | 7 |
| Junction-to-top characterization parameter ψJT | OPA376, DBV (SOT-23), 5 pins | typ 10.9 °C/W | 7 |
| Junction-to-board characterization parameter ψJB | OPA376, DBV (SOT-23), 5 pins | typ 84.9 °C/W | 7 |
| Input offset voltage VOS | TA = 25°C, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, VOUT = VS / 2 | typ 5 · max 25 uV | 8 |
| Input offset voltage versus temperature dVOS/dT | TA = –40°C to +85°C | typ 0.26 · max 1 uV/°C | 8 |
| Input offset voltage versus temperature dVOS/dT | TA = –40°C to +125°C | typ 0.32 · max 2 uV/°C | 8 |
| Input offset voltage versus power supply PSRR | TA = 25°C, VS = 2.2 V to 5.5 V, VCM < (V+) – 1.3 V | typ 5 · max 20 uV/V | 8 |
| Input offset voltage versus power supply PSRR | TA = –40°C to +125°C, VS = 2.2 V to 5.5 V, VCM < (V+) – 1.3 V | typ 5 uV/V | 8 |
| Input bias current IB | TA = 25°C | typ 0.2 · max 10 pA | 8 |
| Input offset current IOS | TA = 25°C | typ 0.2 · max 10 pA | 8 |
| Input voltage noise | f = 0.1 Hz to 10 Hz | typ 0.8 uVPP | 8 |
| Input voltage noise density en | f = 1 kHz | typ 7.5 nV/√Hz | 8 |
| Input current noise in | f = 1 kHz | typ 2 fA/√Hz | 8 |
| Common-mode rejection ratio CMRR | (V–) < VCM < (V+) – 1.3 V | min 76 · typ 90 dB | 8 |
| Differential | Input capacitance | typ 6.5 pF | 8 |
| Common-mode | Input capacitance | typ 13 pF | 8 |
| Open-loop voltage gain AOL | 50 mV < VO < (V+) – 50 mV, RL = 10 kΩ | min 120 · typ 134 dB | 8 |
| Open-loop voltage gain AOL | 100 mV < VO < (V+) – 100 mV, RL = 2 kΩ | min 120 · typ 126 dB | 8 |
| Gain-bandwidth product GBW | CL = 100 pF, VS = 5.5 V | typ 5.5 MHz | 8 |
| Slew rate SR | G=1; CL = 100 pF, VS = 5.5 V | typ 2 V/us | 8 |
| Settling time tS | To 0.1%, 2-V step , G = 1; CL = 100 pF, VS = 5.5 V | typ 1.6 us | 8 |
| Settling time tS | To 0.01%, 2-V step , G = 1; CL = 100 pF, VS = 5.5 V | typ 2 us | 8 |
| Overload recovery time | VIN × gain > VS; CL = 100 pF, VS = 5.5 V | typ 0.33 us | 8 |
| Total harmonic distortion + noise THD+N | VO = 1 VRMS, G = 1, f = 1 kHz, RL = 10 kΩ; CL = 100 pF, VS = 5.5 V | typ 0.00027 % | 8 |
| Voltage output swing from rail | SOT23-5; TA = 25°C, RL = 10 kΩ | typ 10 · max 20 mV | 9 |
| Voltage output swing from rail | TA = –40°C to +125°C, RL = 10 kΩ | max 40 mV | 9 |
| Voltage output swing from rail | SOT23-5; TA = 25°C, RL = 2 kΩ | typ 40 · max 50 mV | 9 |
| Voltage output swing from rail | TA = –40°C to +125°C, RL = 2 kΩ | max 80 mV | 9 |
| Short-circuit current ISC | Positive output current | typ 30 mA | 9 |
| Short-circuit current ISC | Negative output current | typ -50 mA | 9 |
| Open-loop output impedance RO | TA = 25°C, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, VOUT = VS / 2 | typ 150 Ω | 9 |
| Specified voltage range VS | min 2.2 · max 5.5 V | 9 | |
| Operating voltage range | min 2 · max 5.5 V | 9 | |
| Quiescent current per amplifier IQ | TA = 25°C, IO = 0, VS = 5.5 V, VCM < (V+) – 1.3 V | typ 760 · max 950 uA | 9 |
| Quiescent current per amplifier IQ | TA = –40°C to +125°C | max 1 mA | 9 |
| Specified range | Temperature | min -40 · max 125 °C | 9 |
| Operating range | Temperature | min -40 · max 150 °C | 9 |
Pins, by the datasheet
5- 1 OUT
- Output signal. · p. 3
- 2 V–
- Supply voltage–. · p. 3
- 3 +IN
- Input signal +. · p. 3
- 4 –IN
- Input signal –. · p. 3
- 5 V+
- Supply voltage+. · p. 3
Parts like it
8LTC321AXT5/R6
SOT-23-5L-40℃~+125℃ 1 1.8V~5.5V 150pA 1MHz 1V/us 1uV/℃ 29nV/√Hz@1kHz 45mA 500uV 5pA 85uA 96dB EMI filtering/RF suppression、ESD protection、Built-in compensation、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsOPA335AIDBV
SOT-23-5-2.75V~-1.35V、1.35V~2.75V -40℃~+125℃ 1 1.6V/us 120pA 130dB 1uV 1uV/℃ 2.7V~5.5V 285uA 2MHz 50mA 70pA Rail-to-rail output Zero drift / auto-zero SOT-23-5 Precision Op Amps ROHSTexas InstrumentsPrecision OpAmpsLTC8551XT5/R6
SOT-23-5L-2.75V~-1V、1V~2.75V -40℃~+125℃ 1.2V/us 1.5MHz 1.8V~5.5V 112dB 125uA 19nV/√Hz@1kHz 2uV 40mA 5nV/℃ 700pA EMI filtering/RF suppression、Zero drift / auto-zero、ESD protection、Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsLTC725XT5/R6
SOT-23-5L-40℃~+125℃ 1 1.8V~5.5V 11MHz 11V/us 1pA 2.3uV/℃ 350uV 500pA 750uA 75mA 8nV/√Hz@10kHz 96dB EMI filtering/RF suppression、ESD protection、Built-in compensation、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsLTC8331XT5/R6
SOT-23-5L-2.75V~-900mV、900mV~2.75V -40℃~+125℃ 0.22V/us 1 1.8V~5.5V 100pA 10nV/℃ 112dB 15uV 26uA 350kHz 40mA 57nV/√Hz@1kHz 70pA EMI filtering/RF suppression、Zero drift / auto-zero、ESD protection、Built-in compensation、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsLTC8841XT5/R6
SOT-23-5L-2.75V~-900mV、900mV~2.75V -40℃~+125℃ 1 1.2V/us 1.5MHz 1.8V~5.5V 1pA 25nV/√Hz@1kHz 350uV 45mA 500pA 800nV/℃ 85uA 96dB EMI filtering/RF suppression、ESD protection、Built-in compensation、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsLTA8091XT5/R6
SOT-23-5L-24V~-2.25V、2.25V~24V -40℃~+125℃ 1 1.5uV/℃ 100uV 10pA 116dB 20V/us 22MHz 4.5V~48V 45mA 4nV/√Hz@10kHz 5pA 7.1mA EMI filtering/RF suppression、ESD protection、Reverse-phase input protection SOT-23-5L Precision Op Amps ROHSLinearinPrecision OpAmpsHPA00141AIDBV
SOT-23-5Zero drift / auto-zero、ESD Protection、Built-in compensation、Reverse-phase input protection SOT-23-5 Precision Op Amps ROHSTexas InstrumentsPrecision OpAmps
Questions
Is there a KiCad symbol and footprint for the OPA376AIDBV?
Yes. The symbol is Amplifier_Operational:OPA376xxDBV and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the OPA376AIDBV?
SOT-23-5, with 5 pins. Its footprint is drawn on this page.
Where is the OPA376AIDBV datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the OPA376AIDBV?
JLCPCB lists it as part C42134, with 1,478 in stock; the sellers' links on this page open their listings.
What can replace the OPA376AIDBV?
Parts like it in the library: the LTC321AXT5/R6 by Linearin, the OPA335AIDBV by Texas Instruments, the LTC8551XT5/R6 by Linearin and the LTC725XT5/R6 by Linearin. Check their datasheets: a part that fits the footprint may still differ in its ratings.